Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods

This document specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates. Method A describes the determination of the modulus in shear. Method B describes the determination of the strength of the bonds. The methods are applicable primarily to test pieces prepared in the laboratory under standard conditions, such can be used to provide data for the development and control of rubber compounds and methods of manufacture of bonded shear units.

Caoutchouc vulcanisé ou thermoplastique — Détermination du module de cisaillement et de la force d'adhérence à des plaques rigides — Méthodes du quadruple cisaillement

Le présent document spécifie des méthodes de détermination du module de cisaillement et de la force d'adhérence du caoutchouc au métal ou à d'autres plaques rigides, lorsqu'il est collé entre quatre plaques parallèles. La méthode A décrit la détermination du module de cisaillement. La méthode B décrit la détermination de la force d'adhérence. Les méthodes sont applicables principalement aux éprouvettes préparées en laboratoire dans des conditions normalisées, de façon à pouvoir être utilisées pour fournir des données permettant d'élaborer et de contrôler les mélanges de caoutchouc et les méthodes de fabrication de pièces collées.

General Information

Status
Published
Publication Date
14-Aug-2022
Current Stage
6060 - International Standard published
Start Date
15-Aug-2022
Due Date
09-May-2023
Completion Date
15-Aug-2022
Ref Project

Relations

Buy Standard

Standard
ISO 1827:2022 - Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods Released:15. 08. 2022
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 1827:2022 - Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods Released:15. 08. 2022
French language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
REDLINE ISO/FDIS 1827 - Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods Released:5/12/2022
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 1827 - Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods Released:5/12/2022
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 1827 - Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods Released:5/19/2022
French language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 1827
Sixth edition
2022-08
Rubber, vulcanized or
thermoplastic — Determination of
shear modulus and adhesion to rigid
plates — Quadruple-shear methods
Caoutchouc vulcanisé ou thermoplastique — Détermination du
module de cisaillement et de la force d'adhérence à des plaques
rigides — Méthodes du quadruple cisaillement
Reference number
ISO 1827:2022(E)
© ISO 2022
---------------------- Page: 1 ----------------------
ISO 1827:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2022 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 1827:2022(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ..................................................................................................................................................................................... 1

3 Terms and definitions .................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 2

4.1 Method A — Determination of the shear modulus................................................................................................. 2

4.2 Method B — Determination of the adhesion ............................................................................................................... 2

5 Apparatus .................................................................................................................................................................................................................... 2

6 Calibration ..................................................................................................................................................................................................................2

7 Test piece ..................................................................................................................................................................................................................... 2

7.1 Shape and dimensions ..................................................................................................................................................................... 2

7.2 Preparation ................................................................................................................................................................................................ 3

7.2.1 Preparation of rigid plates ......................................................................................................................................... 3

7.2.2 Preparation using unmoulded rubber ............................................................................................................ 3

7.2.3 Preparation using pre-moulded rubber ........................................................................................................ 3

7.3 Number of test pieces ....................................................................................................................................................................... 4

8 Time interval between vulcanization and testing ........................................................................................................... 4

9 Conditioning ............................................................................................................................................................................................................. 4

10 Temperature of test .......................................................................................................................................................................................... 4

11 Procedure .................................................................................................................................................................................................................... 4

11.1 Method A ...................................................................................................................................................................................................... 4

11.2 Method B ...................................................................................................................................................................................................... 5

12 Expression of results .......................................................................................................................................................................................5

12.1 Method A ...................................................................................................................................................................................................... 5

12.2 Method B ...................................................................................................................................................................................................... 6

13 Test report .................................................................................................................................................................................................................. 6

13.1 For method A ............................................................................................................................................................................................ 6

13.2 For method B ............................................................................................................................................................................................ 7

Annex A (normative) Calibration schedule ........................................................................................................................................... ........8

iii
© ISO 2022 – All rights reserved
---------------------- Page: 3 ----------------------
ISO 1827:2022(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/

iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,

Subcommittee SC 2, Testing and analysis.

This sixth edition cancels and replaces the fifth edition (ISO 1827:2016), of which it constitutes a minor

revision.
The changes are as follows:
— the normative references have been updated.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html.
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 1827:2022(E)
Rubber, vulcanized or thermoplastic — Determination of
shear modulus and adhesion to rigid plates — Quadruple-
shear methods

WARNING 1 — Persons using this document should be familiar with normal laboratory practice.

This document does not purport to address all of the safety problems, if any, associated with

its use. It is the responsibility of the user to establish appropriate safety and determine the

applicability of any other restrictions.

WARNING 2 — Certain procedures specified in this document can involve the use or generation

of substances, or the generation of waste, that can constitute a local environmental hazard.

Reference should be made to appropriate documentation on safe handling and disposal after

use.
1 Scope

This document specifies methods for the determination of the modulus in shear and the strength of

bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.

Method A describes the determination of the modulus in shear.
Method B describes the determination of the strength of the bonds.

The methods are applicable primarily to test pieces prepared in the laboratory under standard

conditions, such can be used to provide data for the development and control of rubber compounds and

methods of manufacture of bonded shear units.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 5893:2019, Rubber and plastics test equipment — Tensile, flexural and compression types (constant

rate of traverse) — Specification
ISO 18899:2013, Rubber — Guide to the calibration of test equipment

ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test

methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminology databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 1827:2022(E)
3.1
shear modulus

applied shear stress, calculated with respect to the bonded area of the rubber in a test piece, divided by

the resultant shear strain in the direction of application of the stress

Note 1 to entry: The shear strain (γ) is half the measured deformation divided by the thickness of one rubber

block or element. The shear stress (τ) is the applied force divided by twice the area of a bonded face of one rubber

block or element.

Note 2 to entry: The form of the test piece specified ensures that there is zero applied stress in the direction

normal to the bonded surfaces, so that the deformation can be regarded as simple shear.

Note 3 to entry: This definition of shear modulus is sometimes referred to as the secant modulus.

4 Principle
4.1 Method A — Determination of the shear modulus

The force required to obtain a range of predetermined shear strains of a unit of standard dimensions

comprising four parallelepipeds of rubber symmetrically disposed and bonded to four parallel rigid

plates is measured, the forces being parallel to the bonding surfaces and, as a rule, non-destructive, i.e.

of maximum values appreciably lower than the bond strength.
4.2 Method B — Determination of the adhesion
The force required to cause the rupture of a unit as described for method A is
...

NORME ISO
INTERNATIONALE 1827
Sixième édition
2022-08
Caoutchouc vulcanisé ou
thermoplastique — Détermination du
module de cisaillement et de la force
d'adhérence à des plaques rigides —
Méthodes du quadruple cisaillement
Rubber, vulcanized or thermoplastic — Determination of shear
modulus and adhesion to rigid plates — Quadruple-shear methods
Numéro de référence
ISO 1827:2022(F)
© ISO 2022
---------------------- Page: 1 ----------------------
ISO 1827:2022(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2022

Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette

publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,

y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut

être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.

ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
© ISO 2022 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 1827:2022(F)
Sommaire Page

Avant-propos .............................................................................................................................................................................................................................iv

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ..................................................................................................................................................................................1

3 Termes et définitions ...................................................................................................................................................................................... 1

4 Principe.......................................................................................................................................................................................................................... 2

4.1 Méthode A — Détermination du module de cisaillement ................................................................................ 2

4.2 Méthode B — Détermination de l'adhérence ............................................................................................................... 2

5 Appareillage .............................................................................................................................................................................................................. 2

6 Étalonnage .................................................................................................................................................................................................................. 2

7 Éprouvette .................................................................................................................................................................................................................. 3

7.1 Forme et dimensions ......................................................................................................................................................................... 3

7.2 Préparation ................................................................................................................................................................................................ 3

7.2.1 Préparation des plaques rigides ........................................................................................................................... 3

7.2.2 Préparation avec du caoutchouc non moulé .............................................................................................. 3

7.2.3 Préparation avec du caoutchouc préalablement moulé ................................................................... 4

7.3 Nombre d'éprouvettes...................................................................................................................................................................... 4

8 Délai entre vulcanisation et essai .....................................................................................................................................................4

9 Conditionnement .................................................................................................................................................................................................4

10 Température d'essai ........................................................................................................................................................................................4

11 Mode opératoire ................................................................................................................................................................................................... 4

11.1 Méthode A ................................................................................................................................................................................................... 4

11.2 Méthode B ................................................................................................................................................................................................... 5

12 Expression des résultats ............................................................................................................................................................................. 5

12.1 Méthode A ................................................................................................................................................................................................... 5

12.2 Méthode B ................................................................................................................................................................................................... 6

13 Rapport d'essai ...................................................................................................................................................................................................... 7

13.1 Pour la méthode A................................................................................................................................................................................ 7

13.2 Pour la méthode B ................................................................................................................................................................................ 7

Annexe A (informative) Programme d'étalonnage .............................................................................................................................. 9

iii
© ISO 2022 – Tous droits réservés
---------------------- Page: 3 ----------------------
ISO 1827:2022(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes

nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est

en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.

L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents

critères d'approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.

iso.org/directives).

L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de

brevets reçues par l'ISO (voir www.iso.org/brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion

de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir www.iso.org/avant-propos.

Le présent document a été élaboré par le comité technique ISO/TC 45, Élastomères et produits à base

d'élastomères, sous-comité SC 2, Essais et analyses.

Cette sixième édition annule et remplace la cinquième édition (ISO 1827:2016), dont elle constitue une

révision mineure. Les modifications sont les suivantes:
— les références normatives ont été mises à jour.

Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent

document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes

se trouve à l’adresse www.iso.org/fr/members.html.
© ISO 2022 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 1827:2022(F)
Caoutchouc vulcanisé ou thermoplastique —
Détermination du module de cisaillement et de la force
d'adhérence à des plaques rigides — Méthodes du
quadruple cisaillement

AVERTISSEMENT 1 — Il convient que l'utilisateur du présent document connaisse bien les

pratiques courantes de laboratoire. Le présent document n'a pas pour but de traiter tous les

problèmes de sécurité qui sont, le cas échéant, liés à son utilisation. Il incombe à l'utilisateur

d'établir des pratiques appropriées en matière d'hygiène et de sécurité et de déterminer

l’applicabilité de tout autre restriction.

AVERTISSEMENT 2 — Certains modes opératoires spécifiés dans le présent document peuvent

impliquer l'utilisation ou la génération de substances ou de déchets pouvant représenter

un danger environnemental local. Il convient de se référer à la documentation appropriée

concernant la manipulation et l'élimination après usage en toute sécurité.
1 Domaine d’application

Le présent document spécifie des méthodes de détermination du module de cisaillement et de la force

d'adhérence du caoutchouc au métal ou à d'autres plaques rigides, lorsqu'il est collé entre quatre plaques

parallèles.
La méthode A décrit la détermination du module de cisaillement.
La méthode B décrit la détermination de la force d'adhérence.

Les méthodes sont applicables principalement aux éprouvettes préparées en laboratoire dans des

conditions normalisées, de façon à pouvoir être utilisées pour fournir des données permettant

d'élaborer et de contrôler les mélanges de caoutchouc et les méthodes de fabrication de pièces collées.

2 Références normatives

Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur

contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.

Pour les références non datées, la dernière édition du document de référence s'applique (y compris les

éventuels amendements).

ISO 5893:2019, Appareils d’essai du caoutchouc et des plastiques — Types pour traction, flexion et

compression (vitesse de translation constante) — Spécifications
ISO 18899:2013, Caoutchouc — Guide pour l'étalonnage du matériel d'essai

ISO 23529, Caoutchouc — Procédures générales pour la préparation et le conditionnement des éprouvettes

pour les méthodes d'essais physiques
3 Termes et définitions

Pour les besoins du présent document, les termes et les définitions suivants s'appliquent.

L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en

normalisation, consultables aux adresses suivantes:

— ISO Online browsing platform: disponible à l'adresse https:// www .iso .org/ obp

© ISO 2022 – Tous droits réservés
---------------------- Page: 5 ----------------------
ISO 1827:2022(F)
— IEC Electropedia : disponible à l'adresse https:// www .electropedia .org/
3.1
module de cisaillement

contrainte de cisaillement appliquée, calculée par rapport à l’aire collée du caoutchouc d'une éprouvette,

divisée par la déformation en cisaillement qui en résulte dans la direction d'application de la contrainte

Note 1 à l'article: La déformation en cisaillement (γ) est égale à la moitié de la déformation mesurée, divisée

par l'épaisseur de l'un des blocs ou éléments de caoutchouc. La contrainte en cisaillement (τ) est égale à la force

appliquée, divisée par le double de la surface de la face collée d'un bloc ou d'un élément de caoutchouc.

Note 2 à l'article: La forme de l'éprouvette spécifiée garantit qu'il n'y a aucune contrainte appliquée dans la

direction normale aux surfaces collées, de sorte que la déformation peut être considérée comme un simple

cisaillement.

Note 3 à l'article: Cette définition du module de cisaillement est parfois considérée comme celle du module sécant.

4 Principe
4.1 Méthode A — Détermination du module de cisaillement

On mesure la force nécessaire pour obtenir une série de déformations en cisaillement prédéterminées

sur une éprouvette de dimensions normalisées, comprenant quatre parallélépipèdes de caoutchouc

disposés symétriquement et collés sur quatre plaques parallèles rigides, les forces exercées étant

parallèles aux surfaces collées et, en principe, non destructives, c'est-à-dire limitées à des valeurs

maximales largement inférieures à la force d'adhérence.
4.2 Méthode B — Détermination de l'adhérence

On mesure la force nécessaire pour provoquer la rupture de l'éprouvette décrite pour la méthode A.

5 Appareillage

5.1 Machine d'essai, conforme aux exigences de l'ISO 5893, permettant de mesurer la force avec

une exactitude correspondant à la classe 1 telle que définie dans l'ISO 5893:2019, avec une vitesse de

déplacement de la mâchoire
...

ISO/FDIS 1827:2022(E)
ISO TC 45/SC 2/WG 1
Date: 2022-05-12
Secretariat: JISC

Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion

to rigid plates — Quadruple-shear methods

Caoutchouc vulcanisé ou thermoplastique — Détermination du module de cisaillement et de la

force d'adhérence à des plaques rigides — Méthodes du quadruple cisaillement
FDIS stage
---------------------- Page: 1 ----------------------
ISO/FDIS 1827:2022(E)
© ISO 20212022

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part

of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or

mechanical, including photocopying, or posting on the internet or an intranet, without prior written

permission. Permission can be requested from either ISO at the address below or ISO’s member body

in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
2 © ISO 2022 – All rights reserved
ii © ISO 2022 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/FDIS 1827:2022(E)
Contents

Foreword ............................................................................................................................................................. 5

1 Scope ....................................................................................................................................................... 1

2 Normative references ....................................................................................................................... 1

3 Terms and definitions ....................................................................................................................... 1

4 Principle ................................................................................................................................................ 2

4.1 Method A — Determination of the shear modulus .................................................... 2

4.2 Method B — Determination of the adhesion ............................................................... 2

5 Apparatus .............................................................................................................................................. 2

6 Calibration ............................................................................................................................................ 2

7 Test piece .............................................................................................................................................. 3

7.1 Shape and dimensions ........................................................................................................ 3

7.2 Preparation ............................................................................................................................ 4

7.3 Number of test pieces .......................................................................................................... 5

8 Time interval between vulcanization and testing ................................................................... 5

9 Conditioning ......................................................................................................................................... 5

10 Temperature of test ........................................................................................................................... 5

11 Procedure ............................................................................................................................................. 5

11.1 Method A ................................................................................................................................. 5

11.2 Method B ................................................................................................................................. 6

12 Expression of results ......................................................................................................................... 6

12.1 Method A ................................................................................................................................. 6

12.2 Method B ................................................................................................................................. 7

13 Test report ............................................................................................................................................ 7

13.1 For method A .......................................................................................................................... 7

13.2 For method B .......................................................................................................................... 8

Annex A (normative) Calibration schedule .......................................................................................... 10

Foreword ............................................................................................................................................................ iv

1 Scope ....................................................................................................................................................... 1

2 Normative references ....................................................................................................................... 1

3 Terms and definitions ....................................................................................................................... 1

4 Principle ................................................................................................................................................ 2

4.1 Method A — Determination of the shear modulus .................................................... 2

4.2 Method B — Determination of the adhesion ............................................................... 2

5 Apparatus .............................................................................................................................................. 2

6 Calibration ............................................................................................................................................ 2

7 Test piece .............................................................................................................................................. 2

© ISO 2022 – All rights reserved 3
© ISO 2022 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/FDIS 1827:2022(E)

7.1 Shape and dimensions ........................................................................................................ 2

7.2 Preparation ............................................................................................................................ 3

7.3 Number of test pieces .......................................................................................................... 3

8 Time interval between vulcanization and testing .................................................................... 4

9 Conditioning ......................................................................................................................................... 4

10 Temperature of test ........................................................................................................................... 4

11 Procedure .............................................................................................................................................. 4

11.1 Method A .................................................................................................................................. 4

11.2 Method B .................................................................................................................................. 4

12 Expression of results ......................................................................................................................... 5

12.1 Method A .................................................................................................................................. 5

12.2 Method B .................................................................................................................................. 5

13 Test report ............................................................................................................................................ 6

13.1 For method A .......................................................................................................................... 6

13.2 For method B .......................................................................................................................... 7

Annex A (normative) Calibration schedule .............................................................................................. 8

4 © ISO 2022 – All rights reserved
iv © ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/FDIS 1827:2022(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO

collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directiveswww.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any

patent rights identified during the development of the document will be in the Introduction and/or on

the ISO list of patent declarations received (see www.iso.org/patentswww.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the World

Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.htmlwww.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,

Subcommittee SC 2, Testing and analysis.

This sixsixth edition cancels and replaces the fifth edition (ISO 1827:2016), of which has been technically

revisedit constitutes a minor revision.
The main changes compared to the previous edition are as follows:
— Thethe normative references have been updated.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at
www.iso.org/members.htmlwww.iso.org/members.html.
© ISO 2022 – All rights reserved 5
© ISO 2022 – All rights reserved v
---------------------- Page: 5 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 1827:2022(E)
Rubber, vulcanized or thermoplastic — Determination of shear
modulus and adhesion to rigid plates — Quadruple-shear
methods

WARNING 1 — Persons using this document should be familiar with normal laboratory practice. This

document does not purport to address all of the safety problems, if any, associated with its use. It is the

responsibility of the user to establish appropriate safety and determine the applicability of any other

restrictions.

WARNING 2 — Certain procedures specified in this document mightcan involve the use or generation of

substances, or the generation of waste, that couldcan constitute a local environmental hazard. Reference

should be made to appropriate documentation on safe handling and disposal after use.

1 Scope

This document specifies methods for the determination of the modulus in shear and the strength of bonds

of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.

Method A describes the determination of the modulus in shear.
Method B describes the determination of the strength of the bonds.

The methods are applicable primarily to test pieces prepared in the laboratory under standard

conditions, such as can be used to provide data for the development and control of rubber compounds

and methods of manufacture of bonded shear units.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 5893:2020, Rubber and plastics test equipment — Tensile, flexural and compression types (constant

rate of traverse) — Specification
ISO 18899:2013, Rubber — Guide to the calibration of test equipment

ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test

methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminologicalterminology databases for use in standardization at the following

addresses:

— ISO Online browsing platform: available at https://www.iso.org/obphttps://www.iso.org/obp

— IEC Electropedia: available at https://www.electropedia.org/https://www.electropedia.org/

© ISO 2022 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO/FDIS 1827:2022(E)
3.1
shear modulus

applied shear stress, calculated with respect to the bonded area of the rubber in a test piece, divided by

the resultant shear strain in the direction of application of the stress

Note 1 to entry: The shear strain (γ) is half the measured deformation divided by the thickness of one rubber block

or element. The shear stress (τ) is the applied force divided by twice the area of a bonded face of one rubber block

or element.

Note 2 to entry: The form of the test piece specified ensures that there is zero applied stress

...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 1827
ISO/TC 45/SC 2
Rubber, vulcanized or
Secretariat: JISC
thermoplastic — Determination of
Voting begins on:
2022-05-27 shear modulus and adhesion to rigid
plates — Quadruple-shear methods
Voting terminates on:
2022-07-22
Caoutchouc vulcanisé ou thermoplastique — Détermination du
module de cisaillement et de la force d'adhérence à des plaques
rigides — Méthodes du quadruple cisaillement
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 1827:2022(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2022
---------------------- Page: 1 ----------------------
ISO/FDIS 1827:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2022 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/FDIS 1827:2022(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ..................................................................................................................................................................................... 1

3 Terms and definitions .................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 2

4.1 Method A — Determination of the shear modulus................................................................................................. 2

4.2 Method B — Determination of the adhesion ............................................................................................................... 2

5 Apparatus .................................................................................................................................................................................................................... 2

6 Calibration ..................................................................................................................................................................................................................2

7 Test piece ..................................................................................................................................................................................................................... 2

7.1 Shape and dimensions ..................................................................................................................................................................... 2

7.2 Preparation ................................................................................................................................................................................................ 3

7.2.1 Preparation of rigid plates ......................................................................................................................................... 3

7.2.2 Preparation using unmoulded rubber ............................................................................................................ 3

7.2.3 Preparation using pre-moulded rubber ........................................................................................................ 3

7.3 Number of test pieces ....................................................................................................................................................................... 4

8 Time interval between vulcanization and testing ........................................................................................................... 4

9 Conditioning ............................................................................................................................................................................................................. 4

10 Temperature of test .......................................................................................................................................................................................... 4

11 Procedure .................................................................................................................................................................................................................... 4

11.1 Method A ...................................................................................................................................................................................................... 4

11.2 Method B ...................................................................................................................................................................................................... 5

12 Expression of results .......................................................................................................................................................................................5

12.1 Method A ...................................................................................................................................................................................................... 5

12.2 Method B ...................................................................................................................................................................................................... 6

13 Test report .................................................................................................................................................................................................................. 6

13.1 For method A ............................................................................................................................................................................................ 6

13.2 For method B ............................................................................................................................................................................................ 7

Annex A (normative) Calibration schedule ........................................................................................................................................... ........8

iii
© ISO 2022 – All rights reserved
---------------------- Page: 3 ----------------------
ISO/FDIS 1827:2022(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,

Subcommittee SC 2, Testing and analysis.

This sixth edition cancels and replaces the fifth edition (ISO 1827:2016), of which it constitutes a minor

revision.
The changes are as follows:
— the normative references have been updated.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html.
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 1827:2022(E)
Rubber, vulcanized or thermoplastic — Determination of
shear modulus and adhesion to rigid plates — Quadruple-
shear methods

WARNING 1 — Persons using this document should be familiar with normal laboratory practice.

This document does not purport to address all of the safety problems, if any, associated with

its use. It is the responsibility of the user to establish appropriate safety and determine the

applicability of any other restrictions.

WARNING 2 — Certain procedures specified in this document can involve the use or generation

of substances, or the generation of waste, that can constitute a local environmental hazard.

Reference should be made to appropriate documentation on safe handling and disposal after

use.
1 Scope

This document specifies methods for the determination of the modulus in shear and the strength of

bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.

Method A describes the determination of the modulus in shear.
Method B describes the determination of the strength of the bonds.

The methods are applicable primarily to test pieces prepared in the laboratory under standard

conditions, such can be used to provide data for the development and control of rubber compounds and

methods of manufacture of bonded shear units.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 5893:2020, Rubber and plastics test equipment — Tensile, flexural and compression types (constant

rate of traverse) — Specification
ISO 18899:2013, Rubber — Guide to the calibration of test equipment

ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test

methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminology databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
ISO/FDIS 1827:2022(E)
3.1
shear modulus

applied shear stress, calculated with respect to the bonded area of the rubber in a test piece, divided by

the resultant shear strain in the direction of application of the stress

Note 1 to entry: The shear strain (γ) is half the measured deformation divided by the thickness of one rubber

block or element. The shear stress (τ) is the applied force divided by twice the area of a bonded face of one rubber

block or element.

Note 2 to entry: The form of the test piece specified ensures that there is zero applied stress in the direction

normal to the bonded surfaces, so that the deformation can be regarded as simple shear.

Note 3 to entry: This definition of shear modulus is sometimes referred to as the secant modulus.

4 Principle
4.1 Method A — Determination of the shear modulus

The force required to obtain a range of predetermined shear strains of a unit of standard dimensions

comprising four parallelepipeds of rubber symmetrically disposed and bonded to four parallel rigid

plat
...

PROJET
NORME ISO/FDIS
FINAL
INTERNATIONALE 1827
ISO/TC 45/SC 2
Caoutchouc vulcanisé ou
Secrétariat: JISC
thermoplastique — Détermination du
Début de vote:
2022-05-27 module de cisaillement et de la force
d'adhérence à des plaques rigides —
Vote clos le:
2022-07-22
Méthodes du quadruple cisaillement
Rubber, vulcanized or thermoplastic — Determination of shear
modulus and adhesion to rigid plates — Quadruple-shear methods
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSER-
VATIONS, NOTIFICATION DES DROITS DE PRO-
PRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT
CONNAISSANCE ET À FOURNIR UNE DOCUMEN-
TATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-
Numéro de référence
MERCIALES, AINSI QUE DU POINT DE VUE
ISO/FDIS 1827:2022(F)
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR POSSI-
BILITÉ DE DEVENIR DES NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTA-
TION NATIONALE. © ISO 2022
---------------------- Page: 1 ----------------------
ISO/FDIS 1827:2022(F)
PROJET
NORME ISO/FDIS
FINAL
INTERNATIONALE 1827
ISO/TC 45/SC 2
Caoutchouc vulcanisé ou
Secrétariat: JISC
thermoplastique — Détermination du
Début de vote:
2022-05-27 module de cisaillement et de la force
d'adhérence à des plaques rigides —
Vote clos le:
2022-07-22
Méthodes du quadruple cisaillement
Rubber, vulcanized or thermoplastic — Determination of shear
modulus and adhesion to rigid plates — Quadruple-shear methods
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2022

Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette

publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,

LES DESTINATAIRES DU PRÉSENT PROJET SONT

y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut

INVITÉS À PRÉSENTER, AVEC LEURS OBSER-
VATIONS, NOTIFICATION DES DROITS DE PRO-

être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.

PRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT
ISO copyright office
CONNAISSANCE ET À FOURNIR UNE DOCUMEN-
TATION EXPLICATIVE.
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
Tél.: +41 22 749 01 11
INDUSTRIELLES, TECHNOLOGIQUES ET COM-
Numéro de référence
E-mail: copyright@iso.org
MERCIALES, AINSI QUE DU POINT DE VUE
ISO/FDIS 1827:2022(F)
Web: www.iso.org
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
Publié en Suisse
CONSIDÉRÉS DU POINT DE VUE DE LEUR POSSI-
BILITÉ DE DEVENIR DES NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTA-
© ISO 2022 – Tous droits réservés
TION NATIONALE. © ISO 2022
---------------------- Page: 2 ----------------------
ISO/FDIS 1827:2022(F)
Sommaire Page

Avant-propos .............................................................................................................................................................................................................................iv

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ..................................................................................................................................................................................1

3 Termes et définitions ...................................................................................................................................................................................... 1

4 Principe.......................................................................................................................................................................................................................... 2

4.1 Méthode A — Détermination du module de cisaillement ................................................................................ 2

4.2 Méthode B — Détermination de l'adhérence ............................................................................................................... 2

5 Appareillage .............................................................................................................................................................................................................. 2

6 Étalonnage .................................................................................................................................................................................................................. 2

7 Éprouvette .................................................................................................................................................................................................................. 3

7.1 Forme et dimensions ......................................................................................................................................................................... 3

7.2 Préparation ................................................................................................................................................................................................ 3

7.2.1 Préparation des plaques rigides ........................................................................................................................... 3

7.2.2 Préparation avec du caoutchouc non moulé .............................................................................................. 3

7.2.3 Préparation avec du caoutchouc préalablement moulé ................................................................... 4

7.3 Nombre d'éprouvettes...................................................................................................................................................................... 4

8 Délai entre vulcanisation et essai .....................................................................................................................................................4

9 Conditionnement .................................................................................................................................................................................................4

10 Température d'essai ........................................................................................................................................................................................4

11 Mode opératoire ................................................................................................................................................................................................... 4

11.1 Méthode A ................................................................................................................................................................................................... 4

11.2 Méthode B ................................................................................................................................................................................................... 5

12 Expression des résultats ............................................................................................................................................................................. 5

12.1 Méthode A ................................................................................................................................................................................................... 5

12.2 Méthode B ................................................................................................................................................................................................... 6

13 Rapport d'essai ...................................................................................................................................................................................................... 7

13.1 Pour la méthode A................................................................................................................................................................................ 7

13.2 Pour la méthode B ................................................................................................................................................................................ 7

Annexe A (informative) Programme d'étalonnage .............................................................................................................................. 9

iii
© ISO 2022 – Tous droits réservés
---------------------- Page: 3 ----------------------
ISO/FDIS 1827:2022(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes

nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est

en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.

L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents

critères d'approbation requis pour les différents types de documents ISO. Le présent document a

été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir

www.iso.org/directives).

L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de

brevets reçues par l'ISO (voir www.iso.org/brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion

de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir www.iso.org/avant-propos.

Le présent document a été élaboré par le comité technique ISO/TC 45, Élastomères et produits à base

d'élastomères, sous-comité SC 2, Essais et analyses.

Cette sixième édition annule et remplace la cinquième édition (ISO 1827:2016) qui a fait l’objet d’une

révision mineure.
Les principales modifications sont les suivantes:
— les références normatives ont été mises à jour.

Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent

document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes

se trouve à l’adresse www.iso.org/fr/members.html.
© ISO 2022 – Tous droits réservés
---------------------- Page: 4 ----------------------
PROJET FINAL DE NORME INTERNATIONALE ISO/FDIS 1827:2022(F)
Caoutchouc vulcanisé ou thermoplastique —
Détermination du module de cisaillement et de la force
d'adhérence à des plaques rigides — Méthodes du
quadruple cisaillement

AVERTISSEMENT 1 — Il convient que l'utilisateur du présent document connaisse bien les

pratiques courantes de laboratoire. Le présent document n'a pas pour but de traiter tous les

problèmes de sécurité qui sont, le cas échéant, liés à son utilisation. Il incombe à l'utilisateur

d'établir des pratiques appropriées en matière d'hygiène et de sécurité et de déterminer

l’applicabilité de tout autre restriction.

AVERTISSEMENT 2 — Certains modes opératoires spécifiés dans le présent document peuvent

impliquer l'utilisation ou la génération de substances ou de déchets pouvant représenter

un danger environnemental local. Il convient de se référer à la documentation appropriée

concernant la manipulation et l'élimination après usage en toute sécurité.
1 Domaine d’application

Le présent document spécifie des méthodes de détermination du module de cisaillement et de la force

d'adhérence du caoutchouc au métal ou à d'autres plaques rigides, lorsqu'il est collé entre quatre plaques

parallèles.
La méthode A décrit la détermination du module de cisaillement.
La méthode B décrit la détermination de la force d'adhérence.

Les méthodes sont applicables principalement aux éprouvettes préparées en laboratoire dans des

conditions normalisées, de façon à pouvoir être utilisées pour fournir des données permettant

d'élaborer et de contrôler les mélanges de caoutchouc et les méthodes de fabrication de pièces collées.

2 Références normatives

Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur

contenu, des exigences du présent document. Pour les références datées, seule l'édition citée s'applique.

Pour les références non datées, la dernière édition du document de référence s'applique (y compris les

éventuels amendements).

ISO 5893:2020, Appareils d’essai du caoutchouc et des plastiques — Types pour traction, flexion et

compression (vitesse de translation constante) — Spécifications
ISO 18899:2013, Caoutchouc — Guide pour l'étalonnage du matériel d'essai

ISO 23529, Caoutchouc — Procédures générales pour la préparation et le conditionnement des éprouvettes

pour les méthodes d'essais physiques
3 Termes et définitions

Pour les besoins du présent document, les termes et les définitions suivants s'appliquent.

L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en

normalisation, consultables aux adresses suivantes:

— ISO Online browsing platform: disponible à l'adresse https:// www .iso .org/ obp

© ISO 2022 – Tous droits réservés
---------------------- Page: 5 ----------------------
ISO/FDIS 1827:2022(F)
— IEC Electropedia : disponible à l'adresse https:// www .electropedia .org/
3.1
module de cisaillement

contrainte de cisaillement appliquée, calculée par rapport à l’aire collée du caoutchouc d'une éprouvette,

divisée par la déformation en cisaillement qui en résulte dans la direction d'application de la contrainte

Note 1 à l'article: La déformation en cisaillement (γ) est égale à la moitié de la déformation mesurée, divisée

par l'épaisseur de l'un des blocs ou éléments de caoutchouc. La contrainte en cisaillement (τ) est égale à la force

appliquée, divisée par le double de la surface de la face collée d'un bloc ou d'un élément de caoutchouc.

Note 2 à l'article: La forme de l'éprouvette spécifiée garantit qu'il n'y a aucune contrainte appliquée dans la

direction normale aux surfaces collées, de sorte que la déformation peut être considérée comme un simple

cisaillement.

Note 3 à l'article: Cette définition du module de cisaillement est parfois considérée comme celle du module sécant.

4 Principe
4.1 Méthode A — Détermination du module de cisaillement
On mesure la force nécessaire
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.