ISO/IEC 5021-2:2023
(Main)Telecommunications and information exchange between systems — Wireless LAN access control — Part 2: Dispatching platform
Telecommunications and information exchange between systems — Wireless LAN access control — Part 2: Dispatching platform
This document defines the function, interfaces (IFs), and operating mechanism of CADP and defines the AP association, cloud AC switchover, cloud AC backup and CADP hot backup methods. This document applies to public wireless local area network (WLAN) networking scenarios.
Titre manque — Partie 2: Titre manque
General Information
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 5021-2
First edition
2023-08
Telecommunications and information
exchange between systems — Wireless
LAN access control —
Part 2:
Dispatching platform
Reference number
ISO/IEC 5021-2:2023(E)
© ISO/IEC 2023
---------------------- Page: 1 ----------------------
ISO/IEC 5021-2:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO/IEC 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 5021-2:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 1
5 CADP-based WLAN architecture . 2
6 Operating mechanism of CADP. 3
6.1 CADP service functions . 3
6.2 CADP-based AP association . 4
6.3 CADP-based cloud AC switchover . 5
6.4 CAD-based cloud AC backup . . 5
6.5 CADP hot backup . 5
7 CADP interface . 6
7.1 Interface between CADP and AP (IF1) . 6
7.1.1 CAPWAP protocol basic format . 6
7.1.2 CAPWAP protocol preamble . 7
7.1.3 CAPWAP protocol header . 7
7.1.4 CAPWAP message type . 7
7.1.5 Control message sending and receiving . 8
7.2 Interface between CADP and the WLAN NMS (IF2) . 9
7.2.1 General . 9
7.2.2 APConfig . 9
7.2.3 ACFault . 10
iii
© ISO/IEC 2023 – All rights reserved
---------------------- Page: 3 ----------------------
ISO/IEC 5021-2:2023(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical
activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international
organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
work.
The procedures used to develop this document and those intended for its further maintenance
are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria
needed for the different types of document should be noted. This document was drafted in
accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives or
www.iec.ch/members_experts/refdocs).
ISO and IEC draw attention to the possibility that the implementation of this document may involve the
use of (a) patent(s). ISO and IEC take no position concerning the evidence, validity or applicability of
any claimed patent rights in respect thereof. As of the date of publication of this document, ISO and IEC
had not received notice of (a) patent(s) which may be required to implement this document. However,
implementers are cautioned that this may not represent the latest information, which may be obtained
from the patent database available at www.iso.org/patents and https://patents.iec.ch. ISO and IEC shall
not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www.iso.org/iso/foreword.html. In the IEC, see www.iec.ch/understanding-standards.
This document was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 6, Telecommunications and information exchange between systems.
A list of all parts in the ISO/IEC 5021 series can be found on the ISO and IEC websites.
Any feedback or questions on this document should be directed to the user’s national standards
body. A complete listing of these bodies can be found at www.iso.org/members.html and
www.iec.ch/national-committees.
iv
© ISO/IEC 2023 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO/IEC 5021-2:2023(E)
Telecommunications and information exchange between
systems — Wireless LAN access control —
Part 2:
Dispatching platform
1 Scope
This document defines the function, interfaces (IFs), and operating mechanism of CADP and defines the
AP association, cloud AC switchover, cloud AC backup and CADP hot backup methods. This document
applies to public wireless local area network (WLAN) networking scenarios.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/IEC 5021-1, Telecommunications and information exchange between systems - Wireless LAN Access
Control - Part 1: Networking Architecture Specification
ISO/IEC/IEEE 8802-11, Telecommunications and information exchange between systems — Specific
requirements for local and metropolitan area networks — Part 11: Wireless LAN medium access control
(MAC) and physical layer (PHY) specifications
IETF RFC 5415:2009, Control and Provisioning of Wireless Access Points (CAPWAP) Protocol Specification
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/IEC 5021-1 and
ISO/IEC/IEEE 8802-11 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
wireless termination point
WTP
physical or network entity that contains a radio frequency (RF) antenna and wireless physical layer
(PHY) to transmit and receive station traffic for wireless access networks according to IETF RFC
5415:2009, 1.4
Note 1 to entry: In this document, WTP and access point (AP) refer to the same network entity.
4 Abbreviated terms
The following abbreviated terms apply to this document.
1
© ISO/IEC 2023 – All rights reserved
---------------------- Page: 5 ----------------------
ISO/IEC 5021-2:2023(E)
AP access point
AC access controller
CADP cloud AC dispatch platform
CAPWAP control and provisioning of wireless access points
CPU central processing unit
HTTP hyper text transfer protocol
HTTPS hyper text transfer protocol over secure socket layer
IF interface
MAC media access control
NMS network management system
UDP user datagram protocol
WLAN wireless local area network
WTP wireless termination point
5 CADP-based WLAN architecture
Figure 1 — CADP-based WLAN architecture
2
© ISO/IEC 2023 – All rights reserved
---------------------- Page: 6 ----------------------
ISO/IEC 5021-2:2023(E)
Figure 1 shows the architecture of a CADP-based WLAN, where CADP is deployed at the core layer
of the network to assign the optimal cloud AC to onboarding APs and provide cloud AC switchover
and redundancy for online APs. ISO/IEC 5021-1 shall be referred to for CADP based WLAN network
architecture.
CADP uses the following interfaces (IFs) to communicate with the other WLAN network elements:
a) Interface one (IF1): IF connecting CADP to APs, provides CAPWAP-based information exchange.
Packets transmitted over this IF include AP registration requests that carry AP information and
CADP responses that carry the address of the assigned AC.
b) Interface two (IF2): IF connecting CADP to the WLAN NMS, provides HTTP/HTTPS connection for
the WLAN NMS to deploy AP and AC association information to CADP.
6 Operating mechanism of CADP
6.1 CADP service functions
The WLAN NMS obtains cloud AC load information in real time, including the number of managed APs,
traffic throughput, the number of clients and the CPU usage. Each cloud AC load factor is assign
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.