ISO 13674-1:2010

Road vehicles — Test method for the quantification of on-centre handling — Part 1: Weave test

ISO 13674-1:2010 specifies a test schedule that addresses a particular aspect of the on-centre handling characteristics of a vehicle: the weave test. It is applicable to passenger cars in accordance with ISO 3833, and to light trucks.

Véhicules routiers — Méthode d'essai pour la quantification du centrage — Partie 1: Essai en petite sinusoïde au volant

General Information

• Status: Withdrawn
• Publication Date: 05-May-2010
• ICS: 43.020 - Road vehicles in general
• Technical Committee: ISO/TC 22/SC 33 - Vehicle dynamics and chassis components
• Drafting Committee: ISO/TC 22/SC 33/WG 2 - Vehicle dynamics of passenger cars
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 08-Nov-2023

Relations

• Revised: ISO 13674-1:2023 - Road vehicles — Test method for the quantification of on-centre handling — Part 1: Weave test
• Effective Date: 06-Jun-2022
• Revises: ISO 13674-1:2003 - Road vehicles — Test method for the quantification of on-centre handling — Part 1: Weave test
• Effective Date: 20-Apr-2009

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13674-1
Second edition
2010-05-15

Road vehicles — Test method for the
quantification of on-centre handling —
Part 1:
Weave test
Véhicules routiers — Méthode d'essai pour la quantification
du centrage —
Partie 1: Essai en petite sinusoïde au volant




Reference number
ISO 13674-1:2010(E)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 13674-1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 13674-1:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms, definitions and symbols .1
4 Principle.2
5 Variables.2
5.1 Reference system.2
5.2 Variables to be measured.2
6 Measuring equipment .3
6.1 Description.3
6.2 Transducer installations.3
6.3 Data processing.3
7 Test conditions .3
7.1 General .3
7.2 Test track.4
7.3 Wind velocity .4
7.4 Test vehicle .4
8 Procedure.5
8.1 Warm-up
...