ISO/FDIS 13679

Petroleum and natural gas industries — Procedures for testing casing and tubing connections

Industries du pétrole et du gaz naturel — Modes opératoires d'essai des connexions pour tubes de cuvelage et de production

General Information

• Status: Withdrawn
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• Technical Committee: ISO/TC 67/SC 5 - Casing, tubing and drill pipe
• Drafting Committee: ISO/TC 67/SC 5/WG 2 - Casing and tubing connections and performance properties
• Current Stage: 5098 - Project deleted
• Completion Date: 28-May-2018

Relations

• Revised: ISO 13679:2002 - Petroleum and natural gas industries — Procedures for testing casing and tubing connections
• Effective Date: 15-Apr-2008

Standards Content (Sample)

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 13679
ISO/TC 67/SC 5
Petroleum and natural gas industries —
Secretariat: JISC
Procedures for testing casing and tubing
Voting begins on:
connections
2011-09-15
Voting terminates on:
Industries du pétrole et du gaz naturel — Modes opératoires d'essai des
2011-11-15
connexions pour tubes de cuvelage et de production



Please see the administrative notes on page iii


RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORT-
ING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 13679:2011(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
ISO 2011
NATIONAL REGULATIONS.

---------------------- Page: 1 ----------------------
ISO/FDIS 13679:2011(E)

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.




ii © ISO 2011 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 13679:2011(E)
ISO/CEN PARALLEL PROCESSING
This final draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement. The final draft
was established on the basis of comments received during a parallel enquiry on the draft.
This final draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
two-month approval vote in ISO and formal vote in CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.

In accordance with the provisions of Council Resolution 15/1993, this document is circulated in the
English language only.


© ISO 2011 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/FDIS 13679:2011(E)
Contents Page
Forew ord .vi
Introduction .vii
1  Scope .1
2  Normative references .1
3  Terms and definitions and symbols and abbreviations .1
3.1  Terms and definitions .1
3.2  Symbols .4
3.3  Abbreviations .6
4  General requirements .8
4.1  Connection data sheet .8
4.2  Quality control .9
5  General test requirements .9
5.1  Test principle .9
5.2  Test matrix .
...