ISO 14792:2011
(Main)Road vehicles — Heavy commercial vehicles and buses — Steady-state circular tests
Road vehicles — Heavy commercial vehicles and buses — Steady-state circular tests
ISO 14792:2011 specifies tests for determining the steady-state directional control response of heavy vehicles, one of the factors composing vehicle dynamics and road-holding properties. ISO 14792:2011 is applicable to heavy vehicles, i.e. commercial vehicles, combinations, buses and articulated buses as defined in ISO 3833, covered by Categories M3, N2, N3, O3, and O4 of UNECE (United Nations Economic Commission for Europe) and EC vehicle regulations. These categories pertain to trucks and trailers with a maximum mass above 3,5 t and to buses and articulated buses with a maximum mass above 5 t.
Véhicules routiers — Véhicules utilitaires lourds et autobus — Essais sur trajectoire circulaire en régime permanent
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 14792
Second edition
2011-03-15
Road vehicles — Heavy commercial
vehicles and buses — Steady-state
circular tests
Véhicules routiers — Véhicules utilitaires lourds et autobus — Essais
sur trajectoire circulaire en régime permanent
Reference number
©
ISO 2011
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Test objectives.1
4 Variables and reference system .2
5 Measuring equipment .2
6 Test conditions .2
7 Test procedures.3
7.1 General .3
7.2 Constant radius test.3
7.3 Constant speed, variable-steer angle test .3
7.4 Common test conditions .3
8 Data analysis.4
8.1 General .4
8.2 Steering-wheel angle.4
8.3 Centripetal acceleration.4
8.4 Curvature of trajectory.4
9 Data evaluation and presentation of results .4
9.1 General .4
9.2 Other evaluations and presentation of results.5
Annex A (normative) Test report — Presentation of results.8
Bibliography.13
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14792 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 9, Vehicles
dynamics and road-holding ability.
This second edition cancels and replaces the first edition (ISO 14792:2003), of which it constitutes a minor
revision.
iv © ISO 2011 – All rights reserved
Introduction
The main purpose of this International Standard is to provide repeatable and discriminatory test results.
The dynamic behaviour of a road vehicle is a very important aspect of active vehicle safety. Any given vehicle,
together with its driver and the prevailing environment, constitutes a closed-loop system that is unique. The
task of evaluating the dynamic behaviour is therefore very difficult since the significant interaction of these
driver-vehicle-environment elements are each complex in themselves. A complete and accurate description of
the behaviour of the road vehicle must necessarily involve information obtained from a number of different
tests.
Since this test method quantifies only one small part of the complete vehicle handling characteristics, the
results of these tests can only be considered significant for a correspondingly small part of the overall dynamic
behaviour.
Moreover, insufficient knowledge is available concerning the relationship between overall vehicle dynamic
properties and accident avoidance. A substantial amount of work is necessary to acquire sufficient and
reliable data on the correlation between accident avoidance and vehicle dynamic properties in general and the
results of these tests in particular. Consequently, any application of this test method for regulation purposes
will require proven correlation between test results and accident statistics.
INTERNATIONAL STANDARD ISO 14792:2011(E)
Road vehicles — Heavy commercial vehicles and buses —
Steady-state circular tests
1 Scope
This International Standard specifies tests for determining the steady-state directional control response
of heavy vehicles, one of the factors composing vehicle dynamics and road-holding properties. It is applicable
to heavy vehicles, i.e. commercial vehicles, combinations, buses and articulated buses as defined in ISO 3833,
covered by Categories M3, N2, N3, O3, and O4 of UNECE (United Nations Economic Commission for
Europe) and EC vehicle regulations. These categories pertain to trucks and trailers with a maximum mass
above 3,5 t and to buses and articulated buses with a maximum mass above 5 t.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3833, Road vehicles — Types — Terms and definitions
ISO 8855, Road vehicles — Vehicle dynamics and road-holding ability — Vocabulary
ISO 15037-2:2002, Road vehicles — Vehicle dynamics test methods — Part 2: General conditions for heavy
vehicles and buses
3 Test objectives
The general conditions for
⎯ variables,
⎯ measuring equipment and data processing,
⎯ environment (test track and wind velocity),
⎯ test vehicle preparation (tuning and loading),
⎯ initial driving, and
⎯ the reporting of general data and test conditions
of general significance, independent of the specific vehicle dynamics test procedure, shall be as specified in
ISO 15037-2. They shall apply when vehicle dynamics properties are determined unless other conditions are
required in the standard for the test procedure actually used.
Although this International Standard is intended for combination vehicles as well as for single-unit vehicles,
Clauses 8 and 9, regarding data analysis, evaluation and presentation, deal only with the motion variables of
the single-unit vehicle or of the first unit of combinations. Thus, in order to comply with this International
Standard, the user shall meet the requirements for variables, measuring equipment and data handling only in
as far as they apply to the single-unit vehicle or to the first unit of combinations. Nevertheless, users are
encouraged to measure and analyse the motions of trailing units as appropriate to their particular purposes.
The primary objective of this test procedure is to determine the steady-state turning characteristics of heavy
vehicles for both left- and right-hand turns.
The steady-state turning behaviour of unit vehicles which have more than two axles and/or dual or wide-base
tyres, as is the case with most heavy vehicles, is known to be a strong function of both centripetal acceleration
[3][4]
and path curvature . To characterize the steady-state behaviour of these vehicles, it is therefore necessary
to conduct turning tests on different radii turns as well as at varying levels of centripetal acceleration. Such a
test program may be accomplished through a series of constant radius tests conducted at various radii, or
through a series of constant speed, variable-steer angle tests conducted at different speeds. Indeed, it is
desirable that both types of tests be conducted for a full characterization of the steady-state turning of these
vehicles.
The constant radius test requires the test vehicle to be driven at a constant speed on a path of known,
constant radius. The directional control response characteristics are determined from data obtained by
repeating the procedure at successively higher speeds. To fully characterize the steady-turning of the vehicle,
this procedure shall then be repeated for various radii. The procedure may be tailored to existing test track
facilities by selecting circles or paths of appropriate radii.
The constant speed, variable-steer angle test requires the test vehicle to be driven at a constant speed and
constant steer angle. The directional control response characteristics are determined from data obtained by
repeating the procedure at successively greater steer angles. To fully characterize the steady-turning of the
vehicle, this procedure shall then be repeated at various speeds.
4 Variables and reference system
The variables to be determined may be selected for test purposes from those given in ISO 15037-2 and shall
be monitored using appropriate transducers. The variables relate to the intermediate axis system (X, Y, Z)
(see ISO 8855).
For the purposes of this International Standard, the reference point shall be the centre of gravity of the vehicle
unit.
This provision overrides the similar provision of ISO 15037-2.
Strictly speaking, the steady-state turning performance ought to be evaluated based on centripetal
acceleration, a , rather than on lateral acceleration, a , (see ISO 8855). In most practical situations, however,
c Y
the difference between these two quantities is small and can be ignored. Nevertheless, in a few cases
(e.g. long-wheelbase vehicles operating on small turning radii or any vehicle operating at large body sideslip
angles), the difference could be appreciable. In these cases, measured lateral acceleration needs to be
corrected for sideslip angle to determine centripetal acceleration. In any case, this document refers to
centripetal acceleration throughout rather than to lateral acceleration.
5 Measuring equipment
The measuring and recording equipment shall be in accordance with ISO 15037-2.
6 Test conditions
The limits and specifications for ambient and vehicle test conditions shall be in accordance with ISO 15037-2.
2 © ISO 2011 – All rights reserved
7 Test procedures
7.1 General
The general test specifications shall be in accordance with ISO 15037-2.
7.2 Constant radius test
During this test procedure, the vehicle shall be steered such that it moves on a circular path at a const
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.