Cutter arbors with parallel key and tenon drive — Part 3: Dimensions and designation of tool holders with 7/24 taper for automatic tool changers

ISO 10649-3:2010 specifies the dimensions of cutter arbors with parallel key and tenon drive with 7/24 tapers for automatic tool changer.

Mandrins porte-fraise à entraînement par clavette et tenon — Partie 3: Dimensions et désignation des porte-outils à conicité 7/24 pour changement automatique d'outils

L'ISO 10649-3:2010 spécifie les dimensions des arbres porte-fraise à entraînement par clavette et tenon à conicité 7/24 pour changement automatique d'outils.

General Information

Status
Withdrawn
Publication Date
20-Jul-2010
Withdrawal Date
20-Jul-2010
Technical Committee
Drafting Committee
Current Stage
9599 - Withdrawal of International Standard
Completion Date
15-Oct-2013
Ref Project

Relations

Buy Standard

Standard
ISO 10649-3:2010 - Cutter arbors with parallel key and tenon drive
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 10649-3:2010 - Mandrins porte-fraise a entraînement par clavette et tenon
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10649-3
First edition
2010-08-01

Cutter arbors with parallel key and tenon
drive —
Part 3:
Dimensions and designation of tool
holders with 7/24 taper for automatic tool
changers
Mandrins porte-fraise à entraînement par clavette et tenon —
Partie 3: Dimensions et désignation des porte-outils à conicité 7/24 pour
changement automatique d'outils




Reference number
ISO 10649-3:2010(E)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 10649-3:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10649-3:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10649-3 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 2, High speed
steel cutting tools and their attachments.
ISO 10649 consists of the following parts, under the general title Cutter arbors with parallel key and tenon
drive:
⎯ Part 1: General dimensions
⎯ Part 2: Dimensions and designation of tool holders with hollow taper interface with flange contact surface
⎯ Part 3: Dimensions and designation of tool holders with 7/24 taper for automatic tool changers
⎯ Part 4: Dimensions and designation of tool holders with 7/24 taper without automatic tool changers
The dimensions and designations of tool holders with polygonal taper interface with flange contact surface will
form the subject of a part 5 and the dimensions and designations of tool holders with modular taper interface
with ball track system will form the subject of a part 6.
© ISO 2010 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 10649-3:2010(E)
Introduction
The aim of ISO 10649 (all parts) is to specify the main dimensions for tool holders for this type of interface,
and prevent the risk of collision when exchanging the assembled tool within the machine tools.

iv © ISO 2010 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 10649-3:2010(E)

Cutter arbors with parallel key and tenon drive —
Part 3:
Dimensions and designation of tool holders with 7/24 taper for
automatic tool changers
1 Scope
This part of ISO 10649 specifies the dimensions of cutter arbors with parallel key and tenon drive with 7/24
tapers for automatic tool changer.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individu
...

NORME ISO
INTERNATIONALE 10649-3
Première édition
2010-08-01


Mandrins porte-fraise à entraînement par
clavette et tenon —
Partie 3:
Dimensions et désignation des porte-
outils à conicité 7/24 pour changement
automatique d'outils
Cutter arbors with parallel key and tenon drive —
Part 3: Dimensions and designation of tool holders with 7/24 taper for
automatic tool changers




Numéro de référence
ISO 10649-3:2010(F)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 10649-3:2010(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2010
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2010 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 10649-3:2010(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 10649-3 a été élaborée par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 2, Outils
coupants en acier rapide et leurs attachements.
L'ISO 10649 comprend les parties suivantes, présentées sous le titre général Mandrins porte-fraise à
entraînement par clavette et tenon:
⎯ Partie 1: Dimensions générales
⎯ Partie 2: Dimensions et désignation des porte-outils avec interface à cône creux-face
⎯ Partie 3: Dimensions et désignation des porte-outils à conicité 7/24 pour changement automatique
d'outils
⎯ Partie 4: Dimensions et désignation des porte-outils à conicité 7/24 sans changement automatique
d'outils
Les dimensions et la désignation des porte-outils avec interface à cône polygonal avec face d'appui feront
l'objet d'une future partie 5 et les dimensions et la désignation des porte-outils avec interface à cône
modulaire avec système de serrage à bille feront l'objet d'une future partie 6.
© ISO 2010 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 10649-3:2010(F)
Introduction
Le but de l'ISO 10649 (toutes les parties) est de spécifier les dimensions principales des porte-outils pour ce
type d'interfaces, et d'éviter le risque de collision lors du changement de l'outil assemblé dans la machine.

iv © ISO 2010 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 10649-3:2010(F)

Mandrins porte-fraise à entraînement par clavette et tenon —
Partie 3:
Dimensions et désignation des porte-outils à conicité 7/24 pour
changement automatique d'outils
1 Domaine d'application
La présente partie de l'ISO 10649 spécifie les dimensions des arbres porte-fraise à entraînement par clavette
et tenon à conicité 7/24 pour changement automatique d'outils.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 2768-1, Tolérances générales — Partie 1: Tolérances pour dime
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.