Vibration-generating machines — Guidance for selection — Part 2: Equipment for dynamic structural testing

This document provides guidance to select a vibration generator that will be used to evaluate frequency responses of a test structure or to study how vibration grows/decreases along the structure. These structural dynamics tests can be carried out under field or laboratory conditions (see the ISO 7626 or ISO 10846[4][5][6][7] series). This document describes the selection procedure in terms of the force developed by a single vibration generator. Meanwhile, to move massive structures such as dams or bridges, an assembly of vibration generators is usually applied. Properly phased generators produce in total the same force as calculated for a single vibration generator (see 6.2.6). Guidance also can be applied for the selection of equipment to be used for modal testing to determine natural frequencies, modal shapes and damping in a structure; however, for such a test, more factors than covered by this document usually need to be considered. This document deals only with translational excitation. For equipment applied to generate angular vibration, see Reference [8].

Générateurs de vibrations — Lignes directrices pour la sélection — Partie 2: Moyens pour les essais dynamiques

General Information

Status
Published
Publication Date
11-Jul-2019
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jul-2024
Completion Date
15-Jul-2024
Ref Project

Buy Standard

Standard
ISO 10813-2:2019 - Vibration-generating machines -- Guidance for selection
English language
22 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


INTERNATIONAL ISO
STANDARD 10813-2
First edition
2019-07
Vibration-generating machines —
Guidance for selection —
Part 2:
Equipment for dynamic structural
testing
Générateurs de vibrations — Lignes directrices pour la sélection —
Partie 2: Moyens pour les essais dynamiques
Reference number
©
ISO 2019
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dynamic structural testing . 2
4.1 General . 2
4.2 Excitation types . 2
5 Vibration generators . 2
5.1 Main types of equipment . 2
5.2 Principal characteristics of vibration generators. 3
5.3 Features of different vibration generators . 3
5.3.1 Electrodynamic generator . 3
5.3.2 Electromagnetic vibration generator . 3
5.3.3 Piezoelectric vibration generator . 4
5.3.4 Magnetostrictive vibration generator. 4
5.3.5 Hydraulic vibration generator. 4
5.3.6 Mechanical vibration generator. 4
5.3.7 Impactor . 5
6 Selection procedure . 5
6.1 General . 5
6.2 Procedure . 5
Annex A (informative) Prognosis of mechanical impedance for some types of structures .8
Annex B (informative) Examples of equipment selection .19
Bibliography .22
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 108, Mechanical vibration, shock and
condition monitoring, Subcommittee SC 6, Vibration and shock generating systems.
A list of all parts in the ISO 10813 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

Introduction
A proper selection of vibration generating system, when purchasing new test equipment or updating
existing equipment for the purposes of a specific test or when choosing between the equipment
proposed by a test laboratory or even selecting a laboratory which offers its service to carry out such
a test, is very important. When making this type of selection, several factors should be considered
simultaneously, as follows:
— the type of the test to be carried out (e.g. environmental testing, normal and/or accelerated, dynamic
structural testing, diagnosis, calibration, etc.);
— the motions to be generated during the test;
— the test conditions (e.g. single or multiple excitations, one mode of vibration or combined vibration,
single or combined test, for example, dynamic plus climatic, etc.);
— the objects to be tested and their mounting.
This document deals only with equipment intended to be used for dynamic structural testing, and
selection procedures are predominantly designed to meet the requirements of this testing. However,
specific test conditions and the specific object to be tested can significantly influence the selection.
If the equipment is expected to be used for different types of tests, all possible applications should
be accounted for when selecting. Thus, if the vibration generator is acquired to be applied during
both environmental and dynamic structural testing, ISO 10813-1 and this document should be used
simultaneously. In this document, it is presumed that a system can be selected if it enables to swing
the test object up to a specified level. To generate an excitation without undesired motions, a suitable
control system should be used. The selection of a control system is not considered in this document.
Vibration generating systems are complex machines, so the correct selection always demands a certain
degree of engineering judgement. Consequently, the purchaser, when selecting the vibration test
equipment, can resort to the help of a third party. In such a case, this document can help the purchaser to
ascertain if the solution proposed by the third party is acceptable or not. Designers and manufacturers
can also use this document to assess the market environment.
INTERNATIONAL STANDARD ISO 10813-2:2019(E)
Vibration-generating machines — Guidance for
selection —
Part 2:
Equipment for dynamic structural testing
1 Scope
This document provides guidance to select a vibration generator that will be used to evaluate frequency
responses of a test structure or to study how vibration grows/decreases along the structure. These
structural dynamics tests can be carried out under field or laboratory conditions (see the ISO 7626 or
[4][5][6][7]
ISO 10846 series).
This document describes the selection procedure in terms of the force developed by a single vibration
generator. Meanwhile, to move massive structures such as dams or bridges, an assembly of vibration
generators is usually applied. Properly phased generators produce in total the same force as calculated
for a single vibration generator (see 6.2.6).
Guidance also can be applied for the selection of equipment to be used for modal testing to determine
natural frequencies, modal shapes and damping in a structure; however, for such a test, more factors
than covered by this document usually need to be considered.
This document deals only with translational excitation. For equipment applied to generate angular
vibration, see Reference [8].
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 2041, Mechanical vibration, shock and condition monitoring — Vocabulary
ISO 7626-1, Mechanical vibration and shock — Experimental determination of mechanical mobility —
Part 1: Basic terms and definitions, and transducer specifications
ISO 10846-1, Acoustics and vibration — Laboratory measurement of vibro-acoustic transfer properties of
resilient elements — Part 1: Principles and guidelines
ISO 15261, Vibration and shock generating systems — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2041, ISO 7626-1, ISO 10846-1
and ISO 15261 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
4 Dynamic structural testing
4.1 General
Dynamic structural testing is performed to evaluate such characteristics of a structure as
— frequency responses over a wide range of frequencies,
— modal characteristics (mode shapes, natural frequencies, damping ratios, etc.),
— amplification/attenuation of vibration along the structure.
Knowledge of the dynamic behaviour of structures allows for the, for example:
— design of low-vibration mechanical systems (buildings, machinery, transport and their elements), and
— calculation of isolation systems and means used to reduce vibration.
Level of excitation during the structural testing is not so important as compared with environmental
testing (see ISO 10813-1) provided that linear behaviour of the test structure is maintained. However,
this level should be sufficient to produce the response of the test structure far above the noise floor
at frequencies where the mechanical impedance of the structure reaches its maximum values. For a
non-linear structure, vibration should be excited at the same level as observed under actual operating
conditions.
In a laboratory environment, the test structure can be freely suspended or rigidly supported, whichever
is defined in a relevant specification (see, for example, ISO 7626-2). Single-point or multi-point force
excitation may be used.
Under field conditions, the vibration generator may be used either coupled or uncoupled to the test
structure. Generally, the coupling should be rigid in the direction of excitation but flexible (to allow
r
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.