Electrodynamic vibration generating systems — Performance characteristics — Amendment 1

Systèmes électrodynamiques utilisés pour la génération de vibrations — Caractéristiques de performance — Amendement 1

General Information

Status

Published

Publication Date

28-Nov-2016

ICS

17.160 - Vibrations, shock and vibration measurements

Technical Committee

ISO/TC 108/SC 6 - Vibration and shock generating systems

Drafting Committee

ISO/TC 108/SC 6 - Vibration and shock generating systems

Current Stage

6060 - International Standard published

Due Date

11-Aug-2017

Completion Date

29-Nov-2016

Ref Project

Relations

Amends

ISO 5344:2004 - Electrodynamic vibration generating systems — Performance characteristics

Effective Date

01-Jan-2022

Buy Standard

Standard

ISO 5344:2004/Amd 1:2016

English language

1 pages

sale 15% off

Preview

sale 15% off

Preview

Standards Content (Sample)

ISO 5344:2004/Amd 1:2016

INTERNATIONAL ISO
STANDARD 5344
Second edition
2004-07-01
AMENDMENT 1
2016-12-01
Electrodynamic vibration
generating systems — Performance
characteristics
AMENDMENT 1
Systèmes électrodynamiques utilisés pour la génération de
vibrations — Caractéristiques de performance
AMENDEMENT 1
Reference number
ISO 5344:2004/Amd.1:2016(E)
ISO 2016
---------------------- Page: 1 ----------------------
ISO 5344:2004/Amd.1:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 5344:2004/Amd.1:2016(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. Thi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO

ISO 10813-4:2022(Main)

Vibration generating machines — Guidance for selection — Part 4: Equipment for multi-axial environmental testing

This document gives guidance for the selection of vibration generating equipment for multi-axial environmental testing, depending on the test requirements. Multi-axial environmental test equipment dealt with in this document refers to a vibration test system having controlled vibration of more than one degree of freedom, including linear vibration and angular vibration. In this document, one or more exciter per desired degree of freedom is supposed. The guidance covers such aspects of selection as — number, type and models of exciters, — number, type and models of connectors, — system configuration, and — some components.

Standard
34 pages
English language
sale 15% off

ISO

ISO 6070:2019(Main)

Auxiliary tables for vibration generators — Methods of describing equipment characteristics

This document establishes requirements to ensure appropriate exchange of information between manufacturers and users of auxiliary tables with a view to working out related specifications and possibly to comparing, in an objective way, the characteristics supplied by the manufacturers of auxiliary tables and associated guidance systems. This document is applicable to auxiliary tables which include slip tables and head expanders. It does not cover auxiliary tables with several degrees of freedom. This document provides three levels of description of the test equipment, as follows: a) minimum level; b) medium level; c) high level. This document gives a list of characteristics to be specified for each level of description.

Standard
18 pages
English language
sale 15% off

ISO

ISO 10813-2:2019(Main)

Vibration-generating machines — Guidance for selection — Part 2: Equipment for dynamic structural testing

This document provides guidance to select a vibration generator that will be used to evaluate frequency responses of a test structure or to study how vibration grows/decreases along the structure. These structural dynamics tests can be carried out under field or laboratory conditions (see the ISO 7626 or ISO 10846[4][5][6][7] series). This document describes the selection procedure in terms of the force developed by a single vibration generator. Meanwhile, to move massive structures such as dams or bridges, an assembly of vibration generators is usually applied. Properly phased generators produce in total the same force as calculated for a single vibration generator (see 6.2.6). Guidance also can be applied for the selection of equipment to be used for modal testing to determine natural frequencies, modal shapes and damping in a structure; however, for such a test, more factors than covered by this document usually need to be considered. This document deals only with translational excitation. For equipment applied to generate angular vibration, see Reference [8].

Standard
22 pages
English language
sale 15% off

ISO

ISO 8626:1989/Amd 1:2016(Amendment)

Servo-hydraulic test equipment for generating vibration — Method of describing characteristics — Amendment 1

Standard
1 page
English language
sale 15% off

ISO

ISO 8568:2007(Main)

Mechanical shock — Testing machines — Characteristics and performance

ISO 8568:2007 specifies performance parameters and methods of inspection of mechanical shock-testing machines and gives guidelines for describing their characteristics. It is intended to ensure that the potential user of a particular shock-testing machine is provided with an adequate description of the characteristics of the machine, and also to give guidance on the selection of such machines. ISO 8568:2007 is applicable to the shock-testing machines that are used for demonstrating or evaluating the effect of shock conditions representative of the service environment and also for diagnostic testing. The purpose of the shock test is to reveal mechanical weakness and/or degradation in specified performance. It can also be used to determine the structural integrity of a test specimen or as a means of quality control. Machines used for simulation of earthquakes, sonic booms, explosions and implosions, bursting tests, metalworking, forming, etc. are not covered in ISO 8568:2007.

Standard
23 pages
English language
sale 15% off

ISO

ISO 10813-1:2004(Main)

Vibration generating machines — Guidance for selection — Part 1: Equipment for environmental testing

ISO 10813-1:2004 gives guidance for the selection of vibration generating equipment used for vibration environmental testing, depending on the test requirements. This guidance covers such aspects of selection as the equipment type, the model, and some main components, excluding the control system.

Standard
25 pages
English language
sale 15% off

ISO

ISO 5344:2004(Main)

Electrodynamic vibration generating systems — Performance characteristics

ISO 5344:2004 specifies the performance characteristics and performance test conditions for electrodynamic vibration generator systems and provides a list of additional equipment characteristics that can be declared by the equipment manufacturer. This information can be used by the user or the writer of specifications for equipment for the selection of such a system, taking into account its application. ISO 5344:2004 establishes procedures for calculating the system performance of a system comprising an amplifier from one source and a vibrator from a different source. Such a calculated system performance is less precise than performance measured on a system comprising the actual vibrator and amplifier, and a reserve of calculated force is recommended. It can be desirable to specify separately the acquisition of needed vibrator and/or amplifier interface data, particularly if a vibrator or amplifier is to be acquired to add to an existing installation. It can also be desirable to specify the responsibility for the calculation of performance. ISO 5344:2004 is applicable to equipment producing sine, random and impulse rectilinear vibration. It is implied that all systems are usable for sine testing at least at a low level, since sine capability is needed for specimen response evaluation and transfer function measurements for random and impulse testing. When random capability is specified, it is implied that some sine capability is also available. Similarly, when impulse capability is specified, it is implied that some sine, but not necessarily random, capability is available.

Standard
27 pages
English language
sale 15% off

ISO

ISO 8626:1989(Main)

Servo-hydraulic test equipment for generating vibration — Method of describing characteristics

Establishes a list and the standard method of obtaining certain properties. Provides two levels of description to be used.

Standard
37 pages
English language
sale 15% off
Standard
37 pages
French language
sale 15% off
Standard
37 pages
French language
sale 15% off

ISO

ISO 20816-3:2022(Main)

Mechanical vibration — Measurement and evaluation of machine vibration — Part 3: Industrial machinery with a power rating above 15 kW and operating speeds between 120 r/min and 30 000 r/min

This document specifies the general requirements for evaluating the vibration of various coupled industrial machine types with a power above 15 kW and operating speeds between 120 r/min and 30 000 r/min when measurements are made in-situ. Guidelines for applying evaluation criteria are provided for measurements taken on non-rotating and rotating parts under normal operating conditions. The guidelines are presented in terms of both steady running vibration values and in terms of changes to vibration magnitude, which can occur in these steady values. The numerical values presented are intended to serve as guidelines based on worldwide machine experience, but shall be applied with due regard to specific machine features which can cause these values to be inappropriate. In general, the condition of a machine is assessed by consideration of both the shaft vibration and the associated structural vibration, as well as specific frequency components, which do not always relate to the broadband severity values presented. The machine types covered by this document include: a) steam turbines and generators with outputs less than or equal to 40 MW (see Note 1 and Note 2); b) steam turbines and generators with outputs greater than 40 MW which normally operate at speeds other than 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (although generators seldom fall into this category) (see Note 1); c) rotary compressors; d) industrial gas turbines with outputs less than or equal to 3 MW (see Note 2); e) turbofans; f) electric motors of any type, if the coupling is flexible. When a motor is rigidly coupled to a machine type covered by any other part of ISO20816, the motor may be assessed either against that other part or against ISO 20816-3; g) rolls and mills; h) conveyors; i) variable speed couplings; and j) blowers or fans (see Note 3). NOTE 1 Land based steam turbines, gas turbines and generators of greater than 40 MW capacity, which run at 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min are covered by the requirements of ISO 20816-2. Generators in hydro-electric plants are covered by ISO 20816-5. NOTE 2 Gas turbines of power greater than 3 MW are covered by ISO 20816-4. NOTE 3 The vibration criteria presented in this document are generally only applicable to fans with power ratings greater than 300 kW or fans which are not flexibly supported. As and when circumstances permit, recommendations for other types of fans, including those of lightweight sheet-metal construction, will be prepared. Until these recommendations are available, classifications can be agreed between the manufacturer and the customer; using results of previous operational experience (see also ISO 14694). Machinery including a geared stage can fall under the scope of this document. For performing acceptance tests of gearboxes please refer to ISO 20816-9. The following types of industrial machine are not covered by this document: k) land-based gas turbines, steam turbines and generators with power outputs greater than 40 MW and speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (see ISO20816‑2); l) gas turbine sets with power outputs greater than 3 MW (see ISO20816‑4); m) machine sets in hydraulic power generating and pumping plants (see ISO20816‑5); n) reciprocating machines and machines solidly coupled to reciprocating machines (see ISO10816‑6); o) rotordynamic pumps and any integrated or solidly coupled electric motors where the impeller is mounted directly on the motor shaft or is rigidly attached to it (see ISO10816‑7); p) reciprocating compressor systems (see ISO 20816-8); q) rotary positive displacement compressors (e. g. screw compressors); r) submerged motor-pumps; and s) wind turbines (see ISO10816‑21). The requirements of this document apply to in-situ broad-band vibration measurements taken on the shafts, bearings, bearing pedestals, or housings of machines under steady-state operating conditions within their nominal

Standard
24 pages
English language
sale 15% off
Standard
25 pages
French language
sale 15% off

ISO

ISO 14839-5:2022(Main)

Mechanical vibration — Vibration of rotating machinery equipped with active magnetic bearings — Part 5: Touch-down bearings

This document gives guidelines for identifying: a) The typical architectures of touch-down bearing systems to show which components are likely to comprise such systems and which functions these components provide; NOTE Touch-down bearings are also known as “backup bearings”, “auxiliary bearings”, “catcher bearings” or “landing bearings”. Within this document, the term “touch-down bearings” is used exclusively as defined in ISO 14839‑1. b) The functional requirements for touch-down bearing systems so that clear performance targets can be set; c) Elements to be considered in the design of the dynamic system such that rotordynamic performance can be optimized, both for touch-down bearings and active magnetic bearings (AMBs); d) The environmental factors that have significant impact on touch-down bearing system performance allowing optimization of overall machine design; e) The AMB operational conditions that can give rise to contact within the touch-down bearing system so that such events can be considered as part of an overall machine design. It also considers failure modes within the AMB system that can give rise to a contact event. This ensures that the specification of the touch-down bearings covers all operational requirements; f) The most commonly encountered touch-down bearing failure modes and typical mechanisms for managing these events; g) Typical elements of a design process for touch-down bearing systems including the specification of load requirements, the sizing process, the analytical and simulation methods employed for design validation; h) The parameters to be taken into account when designing a touch-down bearing system acceptance test programme including the test conditions to be specified and the associated instrumentation to be used to ensure successful test execution; i) The condition monitoring and inspection methods that allow the status of in-service touch-down bearings to be evaluated and when necessary identifying the corrective actions to be taken; j) The factors to be considered when designing the maintenance regime for a touch-down bearing system including the actions to be taken after specified events have occurred together with any actions to be performed on a regular basis; k) The factors to be considered regarding other life cycle topics (e.g. obsolescence management, de-commissioning and disposal).

Standard
43 pages
English language
sale 15% off