iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 1464:1985

(Main)

Aerospace — Tripod jacks — Clearance dimensions

Aerospace — Tripod jacks — Clearance dimensions

Specifies the minimum clear space to be provided beneath the aircraft main jacking points. Is not intended to define fully all jack clearance deminsions. In situations where clearances are critical, it should be used as a design aid only. Final critical clearances should be established by using actual jack dimensions.

Aéronautique — Vérins de levage tripodes — Dimensions d'encombrement

La présente Norme internationale spécifie l'espace libre minimal qu'il faut laisser sous les points principaux de levage de l'aéronef de façon à pouvoir mettre des vérins tripodes, assurant ainsi suffisamment d'espace entre les vérins et les parties adjacentes de l'aéronef. La présente Norme internationale n'a pas pour but de définir entièrement toutes les dimensions d'encombrement des vérins. Dans des cas où des espaces libres pour l'encombrement apparaissent critiques, elle doit seulement servir comme un guide de conception. Les espaces critiques finals doivent être établis sur la base des dimensions réelles des vérins.

General Information

Status
Withdrawn
Publication Date
15-May-1985
Withdrawal Date
15-May-1985
ICS
49.100 - Ground service and maintenance equipment
Technical Committee
ISO/TC 20/SC 9 - Air cargo and ground equipment
Drafting Committee
ISO/TC 20/SC 9 - Air cargo and ground equipment
Current Stage
9599 - Withdrawal of International Standard
Completion Date
07-Feb-2018
Ref Project

Relations

Revised
ISO 1464:2018 - Aerospace — Tripod jacks — Clearance dimensions
Effective Date
30-Jan-2016
Revises
ISO 1464:1979 - Aircraft — Clearance dimensions for tripod jacks
Effective Date
15-Apr-2008

Buy Standard

ISO 1464:1985 - Aerospace -- Tripod jacks -- Clearance dimensionsISO 1464:1985 - Aerospace -- Tripod jacks -- Clearance dimensions
PreviousNext
Standard
ISO 1464:1985 - Aerospace -- Tripod jacks -- Clearance dimensions
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 1464:1985 - Aéronautique -- Vérins de levage tripodes -- Dimensions d'encombrementISO 1464:1985 - Aéronautique -- Vérins de levage tripodes -- Dimensions d'encombrement
PreviousNext
Standard
ISO 1464:1985 - Aéronautique -- Vérins de levage tripodes -- Dimensions d'encombrement
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 1464:1985 - Aéronautique -- Vérins de levage tripodes -- Dimensions d'encombrementISO 1464:1985 - Aéronautique -- Vérins de levage tripodes -- Dimensions d'encombrement
PreviousNext
Standard
ISO 1464:1985 - Aéronautique -- Vérins de levage tripodes -- Dimensions d'encombrement
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

International Standard
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION*ME)I(,QYHAPOAHAR OPI-AHM3AUMR fl0 CTAHAAPTM3AL(MM.ORGANISATION INTERNATIONALE DE NORMALISATION
Aerospace - Tripod jacks - Clearance dimensions
Wrins de fevage tripodes - Dimensions d’encombrement
Akronau tique -
Second edition - 1985-05-15
UDC 629.7.081 : 621.866.2 Ref. No. ISO 1464-1985 (E)
lifting equipment, jacks (lifts), dimensions.
Descriptors : aircraft industry, aircraft equipment,
Price based on 4 pages

---------------------- Page: 1 ----------------------
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards bodies (ISO member bodies). The work of preparing International
Standards is normally carried out through ISO technical committees. Esch member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work.
’ Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council. They are approved in accordance with ISO procedures requiring at
least 75 % approval by the member bodies voting.
International Standard ISO 1464 was prepared by Technical Committee ISO/TC 20,
Aircraft and space vehicles.
ISO 1464 was first published in 1979. This second edition cancels and replaces the first
edition, of which it constitutes a technical revision.
0 International Organkation for Standardkation, 1985
Printed in Switzerland

---------------------- Page: 2 ----------------------
ISO 1464-1985 (EI
INTERNATIONAL STANDARD
Aerospace - Tripod jacks - Clearance dimensions
The height of the pyramid shall be sufficient to resch the
1 Scope and field of application
airplane jacking pad at the maximum airplane height before
This International Standard specifies the minimum clear space jacking. The dimensions of the truncated top of the pyramid
shall be such as to meet the dimensions of the inscribed circle
to be provided beneath the aircraft main jacking Points, in Order
given in the table. In addition, in Order
...

Norme internationale @ 1464
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION*MEXAYHAPD/IHAR OPTAHM3AlIMR fl0 CTAHAAPTM3AUMM*ORGANlSATlON INTERNATIONALE DE NORMALISATION
Aeronautique - Verins de levage tripodes - Dimensions
d'encom brement
Aerospace - Tripod jacks - Clearance dimensions
Deuxieme edition - 1985-05-15
- CDU 629.7.081 : 621.866.2 Ref. no : IS0 1464-1985 (F)
Lc
U)
Descripteurs : industrie abronautique, materiel d'aeronef, appareil de levage, vbrin, dimension
E
s
Prix base sur 4 pages

---------------------- Page: 1 ----------------------
Ava n t- pro pos
L’ISO (Organisation internationale de normalisation) est une federation mondiale
d‘organismes nationaux de normalisation (comites membres de I‘ISO). L’elaboration
des Normes internationales est confiee aux comites techniques de I’ISO. Chaque
comite membre interesse par une etude a le droit de faire partie du comite technique
Cree B cet effet. Les organisations internationales, gouvernementales et non gouverne-
mentales, en liaison avec I’ISO, participent Bgalement aux travaux.
Les projets de Normes internationales adoptes par les comites techniques sont sournis
aux comites membres pour approbation, avant leur acceptation comme Normes inter-
nationales par le Conseil de I‘ISO. Les Normes internationales sont approuvees confor-
mement aux procedures de I’ISO qui requierent I’approbation de 75 % au moins des
comites membres votants.
La Norme internationale IS0 1464 a ete Blaboree par le comite technique ISO/TC 20,
ABronautique et espace.
La Norme internationale IS0 1464 a ete pour la premiere fois publiee en 1979. Cette
deuxieme edition annule et remplace la premiere edition, dont elle constitue une
revision technique.
0 Organisation internationale de normalisation, 1985 0
lmprime en Suisse

---------------------- Page: 2 ----------------------
NORM E INTER NATl ON ALE IS0 1464-1985 (F)
Aeronautique - Verins de levage tripodes - Dimensions
d‘encombrement
1 Objet et domaine d‘application La hauteur de la pyrarnide doit Btre suffisante pour atteindre le
point d’appui du verin a la hauteur rnaxirnale de I‘aeronef avant
levage. Les dimensions du sommet tronque de la pyramide doi-
La presente Norrne internationale specifie I‘espace libre minimal
qu’il faut laisser sous les points principaux de levage de I’aero- vent Btre telles qu’elles correspondent aux dimensions du cercle
inscrit au sornrnet donnees dans le tableau. De plus, pour assu-
nef de facon a pouvoir mettre des verins tripodes, assurant
rer une stabilite convenable du verin, la
...

Norme internationale @ 1464
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION*MERflYHAPOflHAfl OPrAHbl3AUblR no CTAHflAPTbl3AUMbl*ORGANlSATlON INTERNATIONALE DE NORMALISATION
Aeronautique - Verins de levage tripodes - Dimensions
d'encom brement
Aerospace - Tripod jacks - Clearance dimensions
Deuxieme edition - 1985-05-15
I CDU 629.7.081 : 621.866.2 Ref. no : IS0 1464-1985 (FI
k
UJ
Descripteurs : industrie aeronautique, materiel d'aeronef, appareil de levage, verin, dimension.
E
A
P
s
Prix base sur 4 pages

---------------------- Page: 1 ----------------------
Avant- p ropos
L'ISO (Organisation internationale de normalisation) est une federation mondiale
d'organismes nationaux de normalisation (comites membres de I'ISO). L'elaboration
des Normes internationales est confiee aux comites techniques de I'ISO. Chaque
comite rnembre interesse par une etude a le droit de faire partie du comite technique
cre6 A cet effet. Les organisations internationales, gouvernementales et non gouverne-
mentales, en liaison avec I'ISO, participent egalement aux travaux.
Les projets de Normes internationales adoptes par les comites techniques sont sournis
aux comites membres pour approbation, avant leur acceptation comme Normes inter-
nationales par le Conseil de I'ISO. Les Normes internationales sont approuvees confor-
mement aux procedures de I'ISO qui requierent I'approbation de 75 % au moins des
comites membres votants.
La Norme internationale IS0 1464 a ete elaboree par le comite technique ISO/TC 20,
ABronautique et espace.
La Norme internationale IS0 1464 a ete pour la premiere fois publiee en 1979. Cette
deuxieme edition annule et remplace la premiere edition, dont elle constitue une
revision technique.
0 Organisation internationale de normalisation, 1985 0
lmprime en Suisse

---------------------- Page: 2 ----------------------
N 0 R M E I N TE R N AT1 0 N A LE IS0 1464-1985 (F)
Aeronautique - Verins de levage tripodes - Dimensions
d‘encombrement
La hauteur de la pyramide doit Btre suffisante pour atteindre le
1 Objet et domaine d‘application
point d’appui du verin a la hauteur maximale de I‘aeronef avant
La presente Norme internationale specifie I’espace libre minimal levage. Les dimensions du sommet tronque de la pyramide doi-
qu’il faut laisser sous les points principaux de levage de I‘aero- vent Btre telles qu’elles correspondent aux dimensions du cercle
nef de facon a pouvoir mettre des verins tripodes, assurant inscrit au sommet donnees
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 12604-3:2022(Main)
Aircraft ground handling — Checked baggage — Part 3: Workstation ergonomics

This document specifies the requirements for workstation ergonomic design of baggage handling agents for individual pieces of baggage checked-in by airline passengers at airports to be carried into aircraft cargo holds. This document applies to all manual handling workplaces in the processing chain for sorting, safe handling and routing of the baggage (containers and bulk baggage, departure and arrival circuits, at terminal and at aircraft, excluding passenger check-in process and loading into aircraft cargo holds). This document doesn't apply to manual handling of odd-sized baggage. This document does not specify the baggage handling systems in and out of airport terminals, except the baggage weights and dimensions to be handled and the critical characteristics of manual workstations. This document does not specify the baggage handling systems in the aircraft.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    12 pages
    French language
    sale 15% off
ISO
ISO 21100:2020(Main)
Air cargo unit load devices — Performance requirements and test parameters

This document specifies the minimum requirements for airworthiness approval of air cargo pallets, nets and containers, generally designated as air cargo unit load devices (ULD). This document is intended to provide a uniform technical reference for air cargo unit load devices approval. As a prerequisite, it is presupposed that the applicable general civil aviation requirements and the aircraft manufacturer's approved Weight and Balance Manual are followed. This document defines the minimum performance requirements and test parameters for air cargo unit load devices requiring approval of airworthiness for installation in an approved aircraft cargo compartment and restraint system that complies with the cargo restraint and occupant protection requirements of EASA CS-25 or 14 CFR Part 25, except for the 9,0 g forward ultimate inertia force of § 25.561(b) (3) (ii). This document applies to airworthiness approved air cargo unit load devices intended for carriage on board civil transport category airplanes type certificated under EASA CS-25 or 14 CFR Part 25, or equivalent. This document exclusively applies to unit load devices airworthiness approval and testing parameters. It does not apply to aircraft design or aircraft operating requirements, which are provided by the approved Weight and Balance Manual for each aircraft type. Other aspects that do not directly pertain to air cargo unit load devices airworthiness approval and testing are not covered by this document and are defined in other International Standards (see Bibliography), e.g.: — ULD design specifications, — ULD in service damage limits, — ULD restraint malfunction limitations, — ULD test methods, — ULD load distribution models, — ULD maximum allowable contours, — ULD CG (centre for gravity) location control means, — ULD pressure equalization methods, — ULD utilization guidelines. Air cargo unit load devices qualified prior to publication of this document were approved in accordance with the requirements of ISO 8097:2001. This document is intended as a TSO approval reference for all new models of unit load devices in the sizes and types it covers, in replacement of ISO 8097. For air cargo unit load devices the size or type of which is not covered in this document, see the requirements of ISO 8097:2001, if their size or type is contained therein, or other equivalent criteria, if not. NOTE 1 ISO 8097 is based on USA National Aerospace Standard NAS 3610 revision 10:1990, Specification for Cargo Unit Load Devices. NOTE 2 The requirements for cargo covers are not defined in this document, except insofar as net restraint is incorporated therein.

  • Standard
    46 pages
    English language
    sale 15% off
  • Draft
    46 pages
    English language
    sale 15% off
ISO
ISO 2026:2020(Main)
Aircraft — Connections for starting engines by air

This document specifies the dimensions of connections for starting aircraft engines by air, which are necessary to ensure international interchangeability of connectors with adaptors. lt also gives the minimum clearances required on the aircraft to provide adequate access for the ground adaptor.

  • Standard
    5 pages
    English language
    sale 15% off
  • Draft
    5 pages
    English language
    sale 15% off
ISO
ISO 21785:2020(Main)
Air cargo unit load devices — Load distribution model

This document defines the industry agreed model for load distribution on air cargo unit load devices (ULD) bases to apply the maximum allowable centre of gravity (C.G.) eccentricity. Its purpose is to establish a common reference load distribution algorithm for: a) comparable and repeatable ULD testing methods, or equivalent numeric simulations; b) aircraft structure and cargo systems design assumptions, consistent with existing airframers practices; and c) definition of operators unit load devices utilization rules and cargo build-up training programs. It applies to all types of unit load devices intended for use on board civil transport aircraft and airworthiness approved in accordance with the performance requirements and testing parameters of either ISO 21100 or, as applicable, ISO 8097. It also applies to non-airworthiness approved (non-certified) containers as defined in ISO 4118, the utilisation of which is controlled by the provisions of the aircraft type's Weight and Balance Manual and other airframe manufacturer's documents.

  • Standard
    7 pages
    English language
    sale 15% off
ISO
ISO 11076:2020(Main)
Aircraft — Deicing/anti-icing methods on the ground

This document establishes the minimum requirements for deicing/anti-icing methods on the ground of main line and regional airplanes, in accordance with ICAO, Document 9640-AN/9401) and the relevant civil aviation requirements, to facilitate the safe operation of main line and regional civil transport airplanes during icing conditions. This document does not specify requirements for specific aircraft model types. Airlines' published manuals, procedures or methods supplement the information contained in this document. Frost, ice or snow deposits, which can seriously affect the aerodynamic performance and/or controllability of an aircraft, are effectively removed by the application of the procedures specified in this document. It is the airplane operator's responsibility to consult airplane manufacturer's aircraft operations manual, aircraft maintenance manual and service letters to determine any limitations/restrictions relating to the use of deicing/anti-icing methods meeting this document for the type and model of airplane to be treated.

  • Standard
    3 pages
    English language
    sale 15% off
ISO
ISO 8267-2:2019(Main)
Aircraft — Tow bar attachment fittings interface requirements — Part 2: Regional aircraft

This document specifies the interface requirements for tow bar attachment fittings on the nose gear (when towing operations are performed from the nose gear) of conventional tricycle type landing gears of commercial civil transport aircraft. Its purpose is to achieve tow bar attachment fittings interface standardization by aircraft mass category (which determines tow bar forces) in order to ensure that a single type of tow bar with a standard connection can be used for all aircraft types within or near that mass category, so as to assist operators and airport handling companies in reducing the number of different tow bar types used. This document is applicable to all new models of regional aircraft within the specified maximum ramp mass range which enter service or are designed after its date of publication. It does not apply to previously in service regional aircraft models, which present a considerable variety of tow bar attachment fittings. However, a simple retrofit modification is described that may make certain in-service fittings compatible with a tow bar head in conformity with this document, where deemed appropriate in order to facilitate operation of such aircraft types at airports. This document is applicable to regional commercial transport aircraft airworthiness certified under FAR/EASA-CS Parts 25 with a maximum ramp mass of ≤ 50 000 kg (110,000 lb). It does not apply to — aircraft airworthiness certified under FAR/EASA-CS Parts 23 as commuter category aeroplanes, and — aircraft airworthiness certified under FAR/EASA-CS Parts 25 but with a maximum ramp mass of > 50 000 kg (110,000 lb), which are covered by ISO 8267‑1. Where a family of existing or contemplated aircraft types bridges two mass categories, use a single tow bar attachment fitting interface for all of them, and consider the use of the standard dimensions for the higher mass category, be it part of this document or ISO 8267‑1, throughout the family. NOTE As far as practical, this document was defined in order to be compatible with as many existing aircraft types as possible in the mass category concerned.

  • Standard
    5 pages
    English language
    sale 15% off
ISO
ISO 11532:2018(Main)
Aircraft ground equipment — Graphical symbols

ISO 11532:2018 establishes common graphical symbols for use on all types of aircraft ground support equipment. They have been compiled for the benefit of those who deal with such equipment, such as airlines, airport handling agencies, airport authorities, manufacturers, etc., in order to facilitate fast and accurate identification of controls, indicators and decals of powered and unpowered equipment. The presentation of this document is based on the recommendations of ISO/TC 145, Graphical symbols. ISO 11532:2018 is also intended to promote standardization of terms for controls, indicators, etc. for aircraft ground support equipment and alleviate language problems. These graphical symbols are intended to be placed on all new equipment and retrofitted on all existing equipment as far as possible. NOTE This document is intended to be read with the documents listed in the bibliography.

  • Standard
    36 pages
    English language
    sale 15% off
  • Standard
    36 pages
    French language
    sale 15% off
ISO
ISO 1464:2018(Main)
Aerospace — Tripod jacks — Clearance dimensions

ISO 1464:2018 specifies the minimum clear space to be provided beneath the aircraft main jacking points, in order to accommodate tripod jacks and thus ensure adequate clearance between the jacks and the adjacent aircraft structure. ISO 1464:2018 is not intended to define fully all jack clearance dimensions. In situations where clearances are critical, it is used as a design aid only. Final critical clearances are established by using actual jack dimensions.

  • Standard
    4 pages
    English language
    sale 15% off
ISO
ISO 10842:2017(Main)
Aircraft — Ground service connections — Locations and types

ISO 10842:2017 specifies the locations and types of aircraft ground service connections in order to optimize ground services both fixed and mobile, for the seven different services hereafter: - 400 Hz electrical power; - preconditioned air for cabin conditioning; - pneumatic power for jet engine start; - potable water; - lavatory service (draining, flushing); - aircraft refuelling; - interphone (headset) connections. It focuses on these aircraft services because: - these connections are those most frequently used during aircraft airport turnaround operations; - in terms of economic benefit, they have the greatest impact through improved efficiency. ISO 10842:2017 is intended to apply to any new type of main line commercial transport category aircraft designed or built after its publication. In addition, it is expected that any substantially modified new derivative aircraft type in the same category (derived from a previously existing type) will, insofar as technically and economically practical, meet the requirements of this document, if specified in the aircraft type specification established between customer airline(s) and manufacturer. It is not the intent of this document to restrict in any way the basic design of any future types of civil passenger transport aircraft. It aims, however, at clarifying for aircraft design engineers the design characteristics which would make it difficult or impossible for a new type of aircraft to be adequately serviced from existing airport facilities. Should basic aircraft design requirements impose on a future model certain characteristics not complying with the present document: - either alternative methods of servicing the aircraft will have to be implemented; or - existing facilities in the airports where such a new type of aircraft is to operate will require some degree of modification/rework; or - additional interface devices/equipment will be required in order to service such a new type of aircraft; in either case resulting in increased aircraft servicing constraints and operating cost.

  • Standard
    11 pages
    English language
    sale 15% off
ISO
ISO 9667:2017(Main)
Aircraft ground support equipment — Tow bars

ISO 9667:2017 specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to any new type of commercial transport category aircraft tow bar designed or built after publication of ISO 9667:2017. The purpose of ISO 9667:2017 is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with ISO 8267.

  • Standard
    8 pages
    English language
    sale 15% off