ISO 7097-1:2025
(Main)Nuclear fuel technology — Determination of uranium in solutions, uranium hexafluoride and solids — Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method
Nuclear fuel technology — Determination of uranium in solutions, uranium hexafluoride and solids — Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method
This document describes an analytical method for the determination of uranium in samples from pure product materials such as U metal, UO2, UO3, uranyl nitrate hexahydrate, uranium hexafluoride and U3O8 from the nuclear fuel cycle. This procedure is sufficiently accurate and precise to be used for nuclear materials accountability. This method can be used directly for the analysis of most uranium and uranium oxide nuclear reactor fuels, either irradiated or un-irradiated, and of uranium nitrate product solutions. Fission products equivalent to up to 10 % burn-up of heavy atoms do not interfere, and other elements which could cause interference are not normally present in sufficient quantity to affect the result significantly. The method recommends that an aliquot of sample is weighed and that a mass titration is used, in order to obtain improved precision and accuracy. This does not preclude the use of alternative techniques which could give equivalent performance. The use of automatic device(s) in the performance of some critical steps of the method has some advantages, mainly in the case of routine analysis.
Technologie du combustible nucléaire — Dosage de l'uranium dans des solutions, l'hexafluorure d'uranium et des solides — Partie 1: Méthode titrimétrique par réduction au fer(II) et oxydation au bichromate de potassium
Le présent document spécifie une méthode analytique de dosage de l'uranium dans les échantillons de produits purs tels que l'U métal, l'UO2, l'UO3, le nitrate d'uranyle hexahydraté et l'hexafluorure d'uranium U3O8 du cycle du combustible. Ce mode opératoire est suffisamment juste et précis pour être utilisé pour la comptabilité des matières nucléaires. Cette méthode peut être appliquée directement pour les analyses de solutions d'uranium et d'oxydes d'uranium, irradiés ou non, et de solution de nitrate d'uranyle de qualité nucléaire. Les produits de fission présents équivalents jusqu'à un taux de combustion des atomes lourds de l'ordre de 10 % n'interfèrent pas, et les autres éléments qui pourraient causer des interférences ne sont pas normalement présents à des teneurs suffisantes pour avoir une incidence sur le résultat de façon significative. La méthode recommande une pesée d'une aliquote d'échantillon et un titrage gravimétrique pour obtenir la précision et l'exactitude nécessaires. Elle n'exclut pas l'emploi d'autres techniques, du moment que celles-ci donnent des résultats équivalents. L'utilisation d'un ou de plusieurs dispositifs automatiques pour l'exécution de certaines étapes critiques de la méthode présente des avantages, principalement dans le cas d'analyses de routine.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 7097-1
Second edition
Nuclear fuel technology —
2025-07
Determination of uranium in
solutions, uranium hexafluoride
and solids —
Part 1:
Iron(II) reduction/potassium
dichromate oxidation
titrimetric method
Technologie du combustible nucléaire — Dosage de l'uranium
dans des solutions, l'hexafluorure d'uranium et des solides —
Partie 1: Méthode titrimétrique par réduction au fer(II) et
oxydation au bichromate de potassium
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Reactions and interferences . 2
5.1 Reactions .2
5.2 Interferences .2
6 Reagents . 3
7 Apparatus . 6
8 Sample preparation . 7
8.1 General .7
8.2 Uranium metal .7
8.3 Uranium dioxide pellets .7
8.4 Uranium oxide powder (UO , UO , U O ) .7
2 3 3 8
8.5 Uranium hexafluoride .8
8.6 Uranium nitrate hexahydrate .8
9 Procedure . 8
10 Expression of the results . 9
10.1 General .9
10.2 Method of calculation .9
10.2.1 Linear interpolation .9
10.2.2 Calculation for the test solution .10
10.2.3 Calculations for samples .10
10.2.4 Average atomic mass .10
10.3 Repeatability .11
10.4 Bias .11
11 Test report .11
Annex A (normative) Uranium hexafluoride sampling and preparation of the test solution .12
Annex B (informative) Expression of results for samples . 14
Bibliography .15
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 85, Nuclear energy, nuclear technologies, and
radiological protection, Subcommittee SC 5, Nuclear installations, processes and technologies.
This second edition cancels and replaces the first edition (ISO 7097-1:2004), which has been technically
revised.
The main changes are as follows:
— aliquot size has been reduced (see Clause 4);
— information on interferences has been updated (see 5.2);
— requirements for standardisation of potassium dichromate titrant were updated (see 6.16);
— previous Annex A was divided into two annexes (Annex A and Annex B).
A list of all parts in the ISO 7097 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
Introduction
The ISO 7097 series documents describe two independent procedures for the determination of uranium in
solutions, uranium hexafluoride and solids. The two procedures are similar: this document uses a titration
with potassium dichromate while ISO 7097-2 uses a titration with cerium(IV).
v
International Standard ISO 7097-1:2025(en)
Nuclear fuel technology — Determination of uranium in
solutions, uranium hexafluoride and solids —
Part 1:
Iron(II) reduction/potassium dichromate oxidation
titrimetric method
1 Scope
This document describes an analytical method for the determination of uranium in samples from pure
product materials such as U metal, UO , UO , uranyl nitrate hexahydrate, uranium hexafluoride and U O
2 3 3 8
from the nuclear fuel cycle. This procedure is sufficiently accurate and precise to be used for nuclear
materials accountability. This method can be used directly for the analysis of most uranium and uranium
oxide nuclear reactor fuels, either irradiated or un-irradiated, and of uranium nitrate product solutions.
Fission products equivalent to up to 10 % burn-up of heavy atoms do not interfere, and other elements which
could cause interference are not normally present in sufficient quantity to affect the result significantly.
The method recommends that an aliquot of sample is weighed and that a mass titration is used, in order
to obtain improved precision and accuracy. This does not preclude the use of alternative techniques which
could give equivalent performance. The use of automatic device(s) in the performance of some critical steps
of the method has some advantages, mainly in the case of routine analysis.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles
and definitions
ISO 9894, Subsampling of uranium hexafluoride in the liquid phase
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5725-1 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Principle
Uranium(VI) is reduced to uranium(IV) in concentrated phosphoric acid reagent, in the presence of sulfamic
acid, by reaction with iron(II) sulfate. The excess of iron(II) sulfate is subsequently oxidized by nitric acid
in the presence of molybdenum, and the uranium(IV) is determined by mass titration with standardized
[2][3][4][5]
potassium dichromate solution to a potentiometric end point .
An aliquot of the sample containing about 15 mg to 50 mg of uranium solution is taken for the titration. An
excess of iron(II) sulfate solution is then added to reduce all the uranium to the quadrivalent state. Sulfamic
acid is added to eliminate nitrite i
...
Norme
internationale
ISO 7097-1
Deuxième édition
Technologie du combustible
2025-07
nucléaire — Dosage de l'uranium
dans des solutions, l'hexafluorure
d'uranium et des solides —
Partie 1:
Méthode titrimétrique par
réduction au fer(II) et oxydation au
bichromate de potassium
Nuclear fuel technology — Determination of uranium in
solutions, uranium hexafluoride and solids —
Part 1: Iron(II) reduction/potassium dichromate oxidation
titrimetric method
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2025
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 2
5 Réactions et interférences . 2
5.1 Réactions .2
5.2 Interférences .3
6 Réactifs . 3
7 Appareillage . 6
8 Préparation de l'échantillon . 7
8.1 Généralités .7
8.2 Uranium métal .8
8.3 Pastilles de dioxyde d'uranium.8
8.4 Poudre d'oxyde d'uranium (UO , UO , U O ) .8
2 3 3 8
8.5 Hexafluorure d'uranium .9
8.6 Nitrate d'uranyle hexahydraté .9
9 Mode opératoire . 9
10 Expression des résultats . 10
10.1 Généralités .10
10.2 Mode de calcul .10
10.2.1 Interpolation linéaire .10
10.2.2 Calcul pour la solution d'essai .11
10.2.3 Calculs pour les échantillons .11
10.2.4 Masse atomique moyenne .11
10.3 Répétabilité .11
10.4 Biais . 12
11 Rapport d'essai .12
Annexe A (normative) Échantillonnage de l'hexafluorure d'uranium et préparation de la
solution à mesurer .13
Annexe B (informative) Expression des résultats pour les échantillons .15
Bibliographie .16
iii
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'ISO attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation
d'un ou de plusieurs brevets. L'ISO ne prend pas position quant à la preuve, à la validité et à l'applicabilité
de tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l'ISO
n'avait pas reçu notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application.
Toutefois, il y a lieu d'avertir les responsables de la mise en application du présent document que des
informations plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à
l'adresse www.iso.org/brevets. L'ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou
partie de tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 85, Énergie nucléaire, technologies
nucléaires, et radioprotection, sous-comité SC 5, Installations nucléaires, procédés et technologies.
Cette deuxième édition annule et remplace la première édition (ISO 7097-1:2004), qui a fait l'objet d'une
révision technique.
Les principales modifications sont les suivantes:
— la quantité d'aliquotes a été réduite (voir l'Article 4);
— les informations sur les interférences ont été mises à jour (voir le paragraphe 5.2);
— les exigences relatives à l'étalonnage de la solution titrante de bichromate de potassium ont été mises à
jour (voir le paragraphe 6.16);
— la précédente Annexe A a été divisée en deux annexes (Annexe A et Annexe B).
Une liste de toutes les parties de la série ISO 7097 se trouve sur le site web de l'ISO.
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l'adresse www.iso.org/fr/members.html.
iv
Introduction
Les documents de la série ISO 7097 décrivent deux modes opératoires indépendants pour la détermination
de l'uranium dans des solutions, l'hexafluorure d'uranium et des solides. Les deux modes opératoires sont
similaires: le présent document utilise le bichromate de potassium pour le titrage tandis que l'ISO 7097-2
utilise le cérium(IV) pour le titrage.
v
Norme internationale ISO 7097-1:2025(fr)
Technologie du combustible nucléaire — Dosage de l'uranium
dans des solutions, l'hexafluorure d'uranium et des solides —
Partie 1:
Méthode titrimétrique par réduction au fer(II) et oxydation
au bichromate de potassium
1 Domaine d'application
Le présent document spécifie une méthode analytique de dosage de l'uranium dans les échantillons
de produits purs tels que l'U métal, l'UO , l'UO , le nitrate d'uranyle hexahydraté et l'hexafluorure
2 3
d'uranium U O du cycle du combustible. Ce mode opératoire est suffisamment juste et précis pour être
3 8
utilisé pour la comptabilité des matières nucléaires. Cette méthode peut être appliquée directement pour les
analyses de solutions d'uranium et d'oxydes d'uranium, irradiés ou non, et de solution de nitrate d'uranyle
de qualité nucléaire. Les produits de fission présents équivalents jusqu'à un taux de combustion des atomes
lourds de l'ordre de 10 % n'interfèrent pas, et les autres éléments qui pourraient causer des interférences ne
sont pas normalement présents à des teneurs suffisantes pour avoir une incidence sur le résultat de façon
significative. La méthode recommande une pesée d'une aliquote d'échantillon et un titrage gravimétrique
pour obtenir la précision et l'exactitude nécessaires. Elle n'exclut pas l'emploi d'autres techniques, du moment
que celles-ci donnent des résultats équivalents. L'utilisation d'un ou de plusieurs dispositifs automatiques
pour l'exécution de certaines étapes critiques de la méthode présente des avantages, principalement dans le
cas d'analyses de routine.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu'ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l'édition citée s'applique. Pour
les références non datées, la dernière édition du document de référence s'applique (y compris les éventuels
amendements).
ISO 3696, Eau pour laboratoire à usage analytique — Spécification et méthodes d'essai
ISO 5725-1, Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 1: Principes généraux
et définitions
ISO 9894, Sous-échantillonnage de l'hexafluorure d'uranium en phase liquide
3 Termes et définitions
Pour les besoins du présent document, les termes et les définition
...
FINAL DRAFT
International
Standard
ISO/FDIS 7097-1
ISO/TC 85/SC 5
Nuclear fuel technology —
Secretariat: BSI
Determination of uranium in
Voting begins on:
solutions, uranium hexafluoride
2025-04-07
and solids —
Voting terminates on:
2025-06-02
Part 1:
Iron(II) reduction/potassium
dichromate oxidation titrimetric
method
Technologie du combustible nucléaire — Dosage de l'uranium
dans des solutions, l'hexafluorure d'uranium et des solides —
Partie 1: Méthode titrimétrique par réduction au fer(II) et
oxydation au bichromate de potassium
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 7097-1:2025(en) © ISO 2025
FINAL DRAFT
ISO/FDIS 7097-1:2025(en)
International
Standard
ISO/FDIS 7097-1
ISO/TC 85/SC 5
Nuclear fuel technology —
Secretariat: BSI
Determination of uranium in
Voting begins on:
solutions, uranium hexafluoride
and solids —
Voting terminates on:
Part 1:
Iron(II) reduction/potassium
dichromate oxidation
titrimetric method
Technologie du combustible nucléaire — Dosage de l'uranium
dans des solutions, l'hexafluorure d'uranium et des solides —
Partie 1: Méthode titrimétrique par réduction au fer(II) et
oxydation au bichromate de potassium
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 7097-1:2025(en) © ISO 2025
ii
ISO/FDIS 7097-1:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Reactions and interferences . 2
5.1 Reactions .2
5.2 Interferences .3
6 Reagents . 3
7 Apparatus . 6
8 Sample preparation . 7
8.1 General .7
8.2 Uranium metal .7
8.3 Uranium dioxide pellets .7
8.4 Uranium oxide powder (UO , UO , U O ) .8
2 3 3 8
8.5 Uranium hexafluoride .8
8.6 Uranium nitrate hexahydrate .8
9 Procedure . 8
10 Expression of the results . 9
10.1 General .9
10.2 Method of calculation .9
10.2.1 Linear interpolation .9
10.2.2 Calculation for the test solution .10
10.2.3 Calculations for samples .10
10.2.4 Average atomic mass .10
10.3 Repeatability .11
10.4 Bias .11
11 Test report .11
Annex A (normative) Uranium hexafluoride sampling and preparation of the test solution .12
Annex B (informative) Expression of results for samples . 14
Bibliography .15
iii
ISO/FDIS 7097-1:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 85, Nuclear energy, nuclear technologies, and
radiological protection, Subcommittee SC 5, Nuclear installations, processes and technologies.
This second edition cancels and replaces the first edition (ISO 7097-1:2004), which has been technically
revised.
The main changes are as follows:
— aliquot size has been reduced (see Clause 4);
— information on interferences has been updated (see 5.2);
— requirements for standardisation of potassium dichromate titrant were updated (see 6.16);
— previous Annex A was divided into two annexes (Annex A and Annex B).
A list of all parts in the ISO 7097 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/FDIS 7097-1:2025(en)
Introduction
The ISO 7097 series documents describe two independent procedures for the determination of uranium in
solutions, uranium hexafluoride and solids. The two procedures are similar: this document uses a titration
with potassium dichromate while ISO 7097-2 uses a titration with cerium(IV).
v
FINAL DRAFT International Standard ISO/FDIS 7097-1:2025(en)
Nuclear fuel technology — Determination of uranium in
solutions, uranium hexafluoride and solids —
Part 1:
Iron(II) reduction/potassium dichromate oxidation
titrimetric method
1 Scope
This document describes an analytical method for the determination of uranium in samples from pure
product materials such as U metal, UO , UO , uranyl nitrate hexahydrate, uranium hexafluoride and U O
2 3 3 8
from the nuclear fuel cycle. This procedure is sufficiently accurate and precise to be used for nuclear
materials accountability. This method can be used directly for the analysis of most uranium and uranium
oxide nuclear reactor fuels, either irradiated or un-irradiated, and of uranium nitrate product solutions.
Fission products equivalent to up to 10 % burn-up of heavy atoms do not interfere, and other elements which
could cause interference are not normally present in sufficient quantity to affect the result significantly.
The method recommends that an aliquot of sample is weighed and that a mass titration is used, in order
to obtain improved precision and accuracy. This does not preclude the use of alternative techniques which
could give equivalent performance. The use of automatic device(s) in the performance of some critical steps
of the method has some advantages, mainly in the case of routine analysis.
2 Normative references
The following documents are referre
...
Formatted
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
ISO/FDIS 7097-1:2025(en)
Style Definition
...
ISO/TC 85/SC 5
Style Definition
...
Style Definition
...
Secretariat: BSI
Style Definition
...
Date: 2025-03-07xx
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Nuclear fuel technology — Determination of uranium in solutions,
Style Definition
...
uranium hexafluoride and solids — —
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Part 1: Style Definition
...
Style Definition
Iron(II) reduction/potassium dichromate oxidation titrimetric
...
Style Definition
method
...
Style Definition
...
Technologie du combustible nucléaire — Dosage de l'uranium dans des solutions, l'hexafluorure d'uranium et
Style Definition
...
des solides —
Style Definition
...
Partie 1: Méthode titrimétrique par réduction au fer(II) et oxydation au bichromate de potassium
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
FDIS stage
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
ISO/FDIS 7097-1:2025(en)
Formatted: Font: Bold
Formatted: HeaderCentered
Commented [eXtyles1]: The reference "ISO 2025" is to a
withdrawn standard
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
Formatted: Default Paragraph Font
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO Formatted: Default Paragraph Font
at the address below or ISO’s member body in the country of the requester.
Formatted: Indent: Left: 0 cm, Right: 0 cm, Space
Before: 0 pt, No page break before, Adjust space
ISO copyright office
between Latin and Asian text, Adjust space between
CP 401 • Ch. de Blandonnet 8
Asian text and numbers
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Formatted: French (France)
EmailE-mail: copyright@iso.org
Formatted: French (France)
Website: www.iso.orgwww.iso.org
Formatted: French (France)
Published in Switzerland
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 11 pt
Formatted: FooterPageRomanNumber, Space After: 0
pt, Line spacing: single
ii © ISO #### 2025 – All rights reserved
ii
ISO/FDIS 7097-1:2025(en)
Formatted: Font: Bold
Formatted: HeaderCentered, Left
Contents Formatted: Adjust space between Latin and Asian text,
Adjust space between Asian text and numbers
Foreword . v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Reactions and interferences . 2
5.1 Reactions . 2
5.2 Interferences . 3
6 Reagents . 3
7 Apparatus . 6
8 Sample preparation . 7
8.1 General. 7
8.2 Uranium metal . 7
8.3 Uranium dioxide pellets . 8
8.4 Uranium oxide powder (UO , UO , U O ) . 8
2 3 3 8
8.5 Uranium hexafluoride . 8
8.6 Uranium nitrate hexahydrate . 8
9 Procedure . 9
10 Expression of the results . 10
10.1 General. 10
10.2 Method of calculation . 10
10.3 Repeatability . 11
10.4 Bias . 12
11 Test report . 12
Annex A (normative) Uranium hexafluoride sampling and preparation of the test solution . 13
Annex B (informative) Expression of results for samples . 16
Bibliography . 18
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1 Formatted: Font: 10 pt
Formatted: Font: 10 pt
4 Principle . 1
Formatted: Font: 10 pt
5 Reactions and interferences . 2
5.1 Reactions . 2
Formatted: FooterCentered, Left, Space Before: 0 pt,
5.2 Interferences . 2
Tab stops: Not at 17.2 cm
Formatted: Font: 11 pt
6 Reagents . 3
Formatted: FooterPageRomanNumber, Left, Space
7 Apparatus . 6
After: 0 pt, Tab stops: Not at 17.2 cm
© ISO 2025 – All rights reserved
iii
ISO/FDIS 7097-1:2025(en)
Formatted: Font: Bold
Formatted: HeaderCentered
8 Sample preparation . 7
8.1 General. 7
8.2 Uranium metal . 7
8.3 Uranium dioxide pellets . 7
8.4 Uranium oxide powder (UO , UO , U O ) . 7
2 3 3 8
8.5 Uranium hexafluoride . 8
8.6 Uranium nitrate hexahydrate . 8
9 Procedure . 8
10 Expression of the results . 9
10.1 General. 9
10.2 Method of calculation . 9
10.2.1 Linear interpolation . 9
10.2.2 Calculation for the test solution . 10
10.2.3 Calculations for samples . 10
10.2.4 Average atomic mass . 10
10.3 Repeatability . 10
10.4 Bias . 11
11 Test report . 11
Annex A (normative) Uranium hexafluoride sampling and preparation of the test solution . 12
A.1 Sampling . 12
A.2 Preparation of the test solution . 12
Annex B (informative) Expression of results for samples . 14
B.1 Uranium metal or oxide . 14
B.2 Uranium hexafluoride . 14
B.3 Uranium nitrate hexahydrate . 14
Bibliography . 15
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 11 pt
Formatted: FooterPageRomanNumber, Space After: 0
pt, Line spacing: single
iv © ISO #### 2025 – All rights reserved
iv
ISO/FDIS 7097-1:2025(en)
Formatted: Font: Bold
Formatted: HeaderCentered, Left
Foreword Formatted: Adjust space between Latin and
...
PROJET FINAL
Norme
internationale
ISO/FDIS 7097-1
ISO/TC 85/SC 5
Technologie du combustible
Secrétariat: BSI
nucléaire — Dosage de l'uranium
Début de vote:
dans des solutions, l'hexafluorure
2025-04-07
d'uranium et des solides —
Vote clos le:
2025-06-02
Partie 1:
Méthode titrimétrique par
réduction au fer(II) et oxydation au
bichromate de potassium
Nuclear fuel technology — Determination of uranium in
solutions, uranium hexafluoride and solids —
Part 1: Iron(II) reduction/potassium dichromate oxidation
titrimetric method
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
Numéro de référence
ISO/FDIS 7097-1:2025(fr) © ISO 2025
PROJET FINAL
ISO/FDIS 7097-1:2025(fr)
Norme
internationale
ISO/FDIS 7097-1
ISO/TC 85/SC 5
Technologie du combustible
Secrétariat: BSI
nucléaire — Dosage de l'uranium
Début de vote:
dans des solutions, l'hexafluorure
2025-04-07
d'uranium et des solides —
Vote clos le:
2025-06-02
Partie 1:
Méthode titrimétrique par
réduction au fer(II) et oxydation au
bichromate de potassium
Nuclear fuel technology — Determination of uranium in
solutions, uranium hexafluoride and solids —
Part 1: Iron(II) reduction/potassium dichromate oxidation
titrimetric method
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
© ISO 2025 INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
NORMES POUVANT
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse Numéro de référence
ISO/FDIS 7097-1:2025(fr) © ISO 2025
ii
ISO/FDIS 7097-1:2025(fr)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 2
5 Réactions et interférences . 2
5.1 Réactions .2
5.2 Interférences .3
6 Réactifs . 3
7 Appareillage . 6
8 Préparation de l'échantillon . 7
8.1 Généralités .7
8.2 Uranium métal .8
8.3 Pastilles de dioxyde d'uranium.8
8.4 Poudre d'oxyde d'uranium (UO , UO , U O ) .8
2 3 3 8
8.5 Hexafluorure d'uranium .9
8.6 Nitrate d'uranyle hexahydraté .9
9 Mode opératoire . 9
10 Expression des résultats . 10
10.1 Généralités .10
10.2 Mode de calcul .10
10.2.1 Interpolation linéaire .10
10.2.2 Calcul pour la solution d'essai .11
10.2.3 Calculs pour les échantillons .11
10.2.4 Masse atomique moyenne .11
10.3 Répétabilité . 12
10.4 Biais . 12
11 Rapport d'essai .12
Annexe A (normative) Échantillonnage de l'hexafluorure d'uranium et préparation de la
solution à mesurer .13
Annexe B (informative) Expression des résultats pour les échantillons .15
Bibliographie .16
iii
ISO/FDIS 7097-1:2025(fr)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'ISO attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation
d'un ou de plusieurs brevets. L'ISO ne prend pas position quant à la preuve, à la validité et à l'applicabilité
de tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l'ISO
n'avait pas reçu notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application.
Toutefois, il y a lieu d'avertir les responsables de la mise en application du présent document que des
informations plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à
l'adresse www.iso.org/brevets. L'ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou
partie de tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 85, Énergie nucléaire, technologies
nucléaires, et radioprotection, sous-comité SC 5, Installations nucléaires, procédés et technologies.
Cette deuxième édition annule et remplace la première édition (ISO 7097-1:2004), qui a fait l'objet d'une
révision technique.
Les principales modifications sont les suivantes:
— la quantité d'aliquotes a été réduite (voir l'Article 4);
— les informations sur les interférences ont été mises à jour (voir le paragraphe 5.2);
— les exigences relatives à l'étalonnage de la solution titrante de bichromate de potassium ont été mises à
jour (voir le paragraphe 6.16);
— la précédente Annexe A a été divisée en deux annexes (Annexe A et Annexe B).
Une liste de toutes les parties de la série ISO 7097 se trouve sur le site web de l'ISO.
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l'adresse www.iso.org/fr/members.html.
iv
ISO/FDIS 7097-1:2025(fr)
Introduction
Les documents de la série ISO 7097 décrivent deux modes opératoires indépendants pour la détermination
de l'uranium dans des solutions, l'hexafluorure d'uranium et des solides. Les deux modes opératoires sont
similaires: le présent document utilise le bichromate de potassium pour le titrage tandis que l'ISO 7097-2
utilise le cérium(IV) pour le titrage.
v
PROJET FINAL Norme internationale ISO/FDIS 7097-1:2025(fr)
Technologie du combustible nucléaire — Dosage de l'uranium
dans des solutions, l'hexafluorure d'uranium et des solides —
Partie 1:
Méthode titrimétrique par réduction au fer(II) et oxydation
au bichromate de potassium
1 Domaine d'application
Le présent document spécifie une méthode analytique de dosage de l'uranium dans les échantillons
de produits purs tels que l'U métal, l'UO , l'UO , le nitrate d'uranyle
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.