ISO 6695:2015

Cycles — Pedal axle and crank assembly with square end fitting — Assembly dimensions

ISO 6695:2015 specifies the dimensions for the assembly of cranks on bottom bracket spindles with square end fittings.

Cycles — Axe de pédalier et manivelle à emmanchement carré — Dimensions d'assemblage

General Information

• Status: Published
• Publication Date: 02-Dec-2015
• ICS: 43.150 - Cycles
• Technical Committee: ISO/TC 149 - Cycles
• Drafting Committee: ISO/TC 149 - Cycles
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 18-Jul-2022

Relations

• Revises: ISO 6695:1991 - Cycles — Pedal axle and crank assembly with square end fitting — Assembly dimensions
• Effective Date: 28-Sep-2013

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6695
Second edition
2015-12-15
Cycles — Pedal axle and crank
assembly with square end fitting —
Assembly dimensions
Cycles — Axe de pédalier et manivelle à emmanchement carré —
Dimensions d’assemblage
Reference number
ISO 6695:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 6695:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6695:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Dimensions . 1
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6695:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directive
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 6695
ISO/TC 149
Cycles — Pedal axle and crank
Secretariat: DIN
assembly with square end fitting —
Voting begins on:
2015­09­07 Assembly dimensions
Voting terminates on:
Cycles — Axe de pédalier et manivelle à emmanchement carré —
2015­11­07
Dimensions d’assemblage
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 6695:2015(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2015

---------------------- Page: 1 ----------------------
ISO/FDIS 6695:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH­1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 6695:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Dimensions . 1
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/FDIS 6695:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non­governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotech
...