ISO 10405:1993

Petroleum and natural gas industries - Care and use of casing and tubing

Industries du pétrole et du gaz naturel — Entretien et utilisation des tubes de cuvelage et de production

General Information

• Status: Withdrawn
• Publication Date: 04-Aug-1993
• Withdrawal Date: 04-Aug-1993
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: ISO/TC 67/SC 5 - Casing, tubing and drill pipe
• Drafting Committee: ISO/TC 67/SC 5 - Casing, tubing and drill pipe
• Current Stage: 9599 - Withdrawal of International Standard
• Start Date: 24-Feb-2000
• Completion Date: 13-Dec-2025

Relations

• Revised: ISO 10405:2000 - Petroleum and natural gas industries - Care and use of casing and tubing
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL IS0
STANDARD
First edition
1993-08-o 1
Petroleum and natural gas industries - Care and
use of casing and tubing
Industries du p&role et du gaz nature/ - Entretien et utilisation des tubes de
cuvelage et de production
Reference number
IS0 10405:1993(E)
IS0 10405:1993(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established
has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
IS0 collaborates closely with the International Electrotechnical Commission (IEC) on
all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for voting. Publication as an International Standard requires
approval by at least 75 % of the member bodies casting a vote.
International Standard IS0 10405 was prepared by the American Petroleum Institute
(API) (as RP 5Cl) and was adopted, under a special “fast-track procedure”, by
Technical Corn-mittee lSO/TC 67, Materialsandequipmentforpetroleum andnatural
gas industries, in parallel with its approval by the IS0 member bodies.
Q IS0 1993
All rights reserved. No part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in
writing from the publisher.
International Organization for Standardization
56 l CH-1211 Geneve 20 l Switzerla nd
Case postale
Printed in Switzerland
ii
IS0 10405:1993(E)
Introduction
International Standard IS0 10405:1993 reproduces the content of API RP 5C1,16th
edition, 1988. ISO, in endorsing thisAP1 document, recognizes that in certain respects
the latter does not comply with all current IS0 rules on the presentation and content
of an International Standard. Therefore, the relevant technical body, within ISO/TC
67, will review IS0 10405:1993 and reissue it, when practicable, in a form complying
with these rules.
This International Standard is not intended to obviate the need for sound engineering
judgement as to when and where this International Standard should be utilized and
users should be aware that additional or differing requirements may be needed to
meet the needs for the particular service intended.
Standards referenced herein may be replaced by other international or national
standards that can be shown to meet or exceed the requirements of the referenced
standards.
. . .
III
This page intentionally left blank

~~~
IS0 10405:1993(E)
INTERNATIONAL STANDARD
Petroleum and natural gas industries - Care and use of
casing and tubing
1 Scope
This International Standard contains guiding principlesforcare and use of casing and tubing forthe petroleum and natural
gas industries.
2 Requirements
Requirements are specified in:
“API Recommended Practice 5Cl (RP SCl), Sixteenth Edition, May 31, 1988, Recommended Practice for Care and Use of
Casing and Tubing”,
which is adopted as IS0 10405.
For the purposes of international standardization, however, modifications shall apply to specific clauses and paragraphs
of API RP 5Cl. These modifications are outlined below.
NOTE - A wavy line in the margin indicates the location of a modification to the text of the API publication.
Page 3
Information given in the POLICY statement is relevant to the API publication only.
Page 6
Subclause 1.1, item b
Second line: delete “API” before “tubular goods”.
Subclause 1.7, item c
Second sentence shall read: “A steel tape calibrated in millimetres should be used.”
Page 7
Subclause 1.13
17th line from bottom shall read: “All values are rounded to the nearest 10 N-m.”
6th line from bottom: Delete the asterisk after the parenthesis and the corresponding footnote.
Subclause 1.14
Subheading above item a shall read: “Round thread, 114 mm through 340 mm OD”
Subheading above item g shall read: “Buttress thread, 114 mm through 340 mm OD”
Item g, 2nd line shall read: ‘I. sizes 114,3 mm through 339,7 mm OD.”
Page 8
Subheading on 1st line shall read: “Round thread and buttress thread, 406 mm, 473 mm and 508 mm OD”
Item h, 1st line shall read:
“Make-up of 406,4 mm, 473 mm and 508 mm OD shall be to a.”
Item h, second paragraph, first sentence shall read:
“On 8-round thread casing a 9,5 mm equilateral triangle is die stamped at a distance of L, + I,6 mm from each end.”
Item h, third paragraph, 4th line shall read: “(67 800 Nom)”
IS0 10405:1993(E)
Subclause 1.15
Second sentence shall read:
“The joint should be made up beyond the hand-tight position at least three turns for sizes 114,3 mm through 177,8 mm
and at least three and a half turns for sizes 193,7 mm and larger, except 244,5 mm and 273,l mm grade P-l 10 and 508 mm
grade J-55 and K-55 which should be made up for turns beyond hand-tight position.”
Page 9
Subclause 1.28
Delete the first sentence starting “When thorough.” and ending ‘I. Dallas, Texas.”
Pages 7 1 to 78, inclusive
Replace part of the existing tables by new table 1.1 and table 1.2.
Page 79
Subclause 2.1, item b
2nd line: Delete “API” before “tubular goods”.
Subclause 2.3
2nd line: Delete “API” before “drift mandrel”.
Subclause 2.9, item c
Second sentence shall read: “A steel tape calibrated in millimetres should be used.”
Page 20
Subclause 2.15
Last line shall read: “. coupling is made up with a torque of 68 Nmm.”
Subclause 2.16
13th line from bottom shall read: “All values are rounded to the nearest 10 Nmm.”
6th and 3rd lines from bottom: Delete the asterisk after the parenthesis (twice), and the corresponding footnote.
Subclause 2.24
Second sentence shall read:
“Tubing 60 mm OD and larger, preferably should be pulled in stands approximately 18 300 mm long or in doubles of
range 2. Stands of tubing 48,3 mm OD or smaller and stands longer than 18 300 mm, should have intermediate support.”
Page 2 7
Subclause 2.33
Delete the third sentence starting “When thorough.” and ending “. Dallas, Texas.‘”
Pages 22 to 24, inclusive
Replace the existing table by new table 2.1.
Page 25
Subclause 3.1
1st line: Delete “API” before “tubular goods“.
Subclause 3.3
in addition to I.C.C. requirement, . .”
2nd line: Delete the words ‘L,
Subclause 3.6, item a
3rd line shall read: “less than 500 mm from the ground.”

IS0 10405:1993(E)
Subclause 3.6, item g
3rd line shall read: “higher than 3 000 mm.,,
Page 26
Subclause 4.4
2nd line below table 4.1: Delete “API” before “specified pipe wall thickness,,.
Page 27
Subclause 6.3
1st line: Substitute “should,, for “shall”.
Subclause 6.5
3rd and 7th lines: Substitute “should” for “shall,,.
Page 28
Subclause 6.10
3rd line: Replace “1 200 F” by “650 OC”.
Subclause 6.11
Replace the present wording with the following:
“When using the metal arc process, low hydrogen electrodes should be used. These include all electrodes with the AWS
classifications Exxl5, Exxl6, and Exxl8 in AWS Specification A5.1, “CoveredCarbonSteelArc Welding Electrodes” (latest
edition*). Low-hydrogen electrodes should not be exposed to the atmosphere until ready for use. Electrodes must be
stored in holding ovens at 65 “C to 150 “C immediately after their containers have been opened. Once removed from the
holding oven, electrodes must be used within 30 min. Electrodes not used within this time limit must be discarded or re-
conditioned by baking at 315 “C to 370 “C for 1 h. After re-conditioning, electrodes must be placed into the holding oven.,,
Subclause 6.13
2nd line: Replace “3 in,, by “75 mm,,.
3rd line: Replace “400 to 600 F” by “205 “C to 315 “C’.
Subclause 6.14
3rd line from bottom: Replace “205 F’ by ‘121 OC’.
Subclause 6.16
2nd line shall read: “4’8 mm diameter or smaller should be used.”
Subclause 6.22
Second sentence shall read:
“If the top side of the float collar and casing collars are welded while the casing is in the rotary or if the practice is not to
make a complete weld,three 75 mm welds should be placed at 120” intervals around 244’5 mm casing, three 100 mm welds
should be placed on larger casing, and three 50 mm welds on smaller casings.’
Subclause 6.23
1st line shall read: “If welds longer than 100 mm to 150 mm are made,”
2nd line shall read: “For example: If 150 mm.’
5th line shall read: ‘I. 150 mm to the left of the weld.’
Subclause 6.26
2nd line shall read: ‘I. welds should be a minimum length of 50 mm at 50 mm intervals.,’
Subclause 6.27
End of 2nd line shall read: “., with 19 mm welds at two equal spacings on the front edge and on 19 mm weld . .’
IS0 10405:1993(E)
New tables
Recommended casing make-up torque 8-round-thread casing
1.1
1.2 Torque values for extremeline casing
2.1 Recommended tubing make-up torque round thread tubing
NOTE - In tables 1.1 and 2.1, the values expressed in pounds per foot (column 2) must be multiplied by 1,488 to determine the linear
density pl.
IS0 10405:1993(E)
TABLE 1.1
RECOMMENDED CASING M.i4KE-UP TORQUE
&ROUND-THREAD CASING
1 2 2 4 3 6
Nominal
Weight,
Size
Torque, ft-lbs (N-m)
Outside Threads
and
Diameter
Maximum
Optimum Minimum
Coupling
Thread
4 bs/ft Grade
in.
(mm)
4.500 114,3) 9.50 H-40 ST&C 770 (1040) 570 960 (1300)
(780)
4.500 114,3) 9.50 J-55 ST&C 1010 (1380) 760 (1030) 1270 (1720)
4.500 114,3) 10.50 J-55 ST&C 1320 (1790) 990 (1350) 1650 (2240)
4.500 114,3) 11.60 J-55 ST&C 1540 (2090) 1150 (1560) 1920 (2610)
4.500 114,3) 9.50 K-55 ST&C 1120 (1520) 840 (1140) (1900)
4.500 114,3) 10.50 K-55 ST&C 1460 (1980) 1100 (1490) (2480)
4.500 114,3) 11.60 K-55 ST&C 1700 (2310) 1280 (1730)
2130 (2890)
4.500 (114,3) 11.60 J-55 LT&C 1620 (2200) 1210
(1650) 2020 (2750)
4.500 (114,3) 11.60 K-55 LT&C 1800 (2430) 1350
(1830) 2240 (3040)
4.500 (114,3) 11.60 c-75 LT&C 2150 (2910) 1610
(2180) 2680 (3640)
4.500 (114,3) 13.50 C-75 LT&C 2600 (3530)
1950 (2640) 3250 (4410)
4.500 (114,3) 11.60 L-80 LT&C 2230 (3030) 1670
(2270) 2790 (3780)
4.500 (114,3) 13.50 L-80 LT&C 2710 (3670) 2030
(2750) 3380 (4590)
4.500 (114,3) 11.60 N-80 LT&C 2280 (3090)
1710 (2310) 2850 (3860)
4.500 (114,3) 13.50 N-80 LT&C 2760 (3740)
2070 (2810) 3450 (4680)
c-90 LT&C 2450 (3320) (2490)
4.500 (114,3) 11.60 1840 3060 (4150)
4.500 (114,3) 13.50 c-90 LT&C 2970
(4030) 2230 (3020) 3710 (5040)
4.500 (114,3) 11.60 c-95 LT&C 2580
(3500) 1940 (2630) 3230 (4380)
LT&C 3130 (4240) 2350
4.500 (114,3) 13.50 c-95 (3180) 3910 (5310)
LT&C 3020
4.500 (114,3) 11.60 P-110 (4100) 2270 (3070) 3780 (5120)
4.500 (114,3) P-110 LT&C 3660
13.50 (4960) 2750 (3720) 4580 (6200)
4.500 (114,3) 15.10 LT&C 4400
P-110 (5960) 3300 (4470) 5500 (7450)
4.500 (114,3) 15.10 Q-125 LT&C 4910 (6650) 3680 (4990) 6130 (8320)
ST&C
5.000 (127,O) 11.50 J-55 1330 1000 (1350) 1660 (2260)
ww
5.000 (127,O) 13.00 J-55 ST&C 1690 (2290) 1260 (1710) 2110 (2860)
5.000 (127,O) 15.00 J-55 ST&C 2070 (2800) 1550 (2100) 2580 (3500)
ST&C
5.000 (127,O) 11.50 K-55 1470 (1990) 1100 (1490) 1830 (2490)
5.000 (127,O) 13.00 K-55 ST&C 1860 (2520) 1390 (1890) 2320 (3150)
5.000 (127,O) 15.00 K-55 ST&C: 2280 (3090) 1710 (2320) 2850 (3860)
5.000 (127,O) 13.00 J-55 LTStC 1820 (2470) 1360 (1850) 2270 (3080)
5.000 (127,O) 15.00 J-55 LT&C 2230 (3020) 1670 (2270) 2790 (3780)
5.000 (127,O) 13.00 K-55 LTStC 2010 (2730) 1510 (2040) 2510 (3410)
127.0) 15.00 K-55 LT&C 2460 (3340) 1850 (2500) 3080 (4170)
127,O) 15.00 c-75 LT&C 2960 (4010) 2220 (3010) 3690 (5010)
(
127,O) 18.00 c-75 LT&C 3770 (5110) 2830 (3830) 4710 (6390)
127,O) 21.40 c-75 LT&C 4660 (6320) 3500 (4740) 5830 (7900)
(
127,O) 24.10 c-75 LT&C 5390 (7310) 4040 (5480) 6740 (9140)
127,O) 15.00 L-80 LT&C 3080 (4170) 2310 (3130) 3850 (5220)
(
127,O) 18.00 L-80 LT&C 3930 (5320) 2940 (3990) 4910 (6650)
5.000 (127,O) 21.40 L-80 LT&C 4860 (6590) 3640 (4940) 6070 (8230)
5.000 (127,O) 24.10 L80 LT&C 5610 (7610) 4210 (5710) 7020 (9520)
5.000 (127,O) 15.00 N-80 LT&C 3140 (4250) 2350 (3190) 3920 (5320)
5.000 (127,O) 18.00 N-80 LT&C 4000 (5420) 3000 (4070) 5000 (6780)
5.000 (127,O) 21.40 N-80 LT&C 4950 (6710) 3710 (5030) 6190 (8390)
5.000 (127,O) 24.10 N-80 LT&C 5720 (7760) 4290 (5820) 7150 (9700)

IS0 10405:1993(E)
TABLE 1.1 (cont.)
RECOMMENDED CASING MAKE-UP TORQUE
&ROUND-THREAD CASING
2 2 4 5 6
Nominal
Weight.
Size
Torque, ft-lbs (Km)
Outside Threads
Diameter and
Optimum Minimum hlaximum
Coupling
Thread
in. 4 bs/ft Grade
(mm)
5.000
127,0) 15.00 c-90 LT&C 3380 (4590) 2540 (3440) 4230 (5730)
5.000
18.00 c-90 LT&C 4310 (5850) 3240 (4390) 5390 (7310)
127,0)
5.000
127,0) 21.40 c-90 LT&C 5340 (7240) 4000 (5430) 6670 (9050)
5.000
127,0) 23.20 c-90 LT&C 5880 (7980) 4410 (5980) 7350 (9970)
5.000
127,0) 24.10 c-90 LT&C 6170 (8370) 4630 (6270) 7710 (10460)
5.000
127,0) 15.00 c-95 LT&C 3560 (4830) 2670 (3630) 4460 (6040)
5.000
127.0) 18.00 c-95 LT&C 4550 (6160) 3410 (4620) 5680 (7700)
5.000 (127.0) 21.40
c-95 LT&C 5620 (7630) 4220 (5720) 7030 (9530)
5.000 (127,0) 24.10
c-95 LT&C 6500 (8810) 4880 (6610) 8130 (11020)
1300 (1760)
5.500 (139,7) 14.00 H-40 ST&C 970 (1320) 1620 (2200)
5.500 139,7) 14.00 J-55 ST&C 1720 (2330) 1290 (1750) 2150 (2920)
5.500 139,7) 15.50 J-55 ST&C 2020 (2730) 1510 (2050) 2520 (3420)
5.500 139,7) 17.00 J-55 ST&C 2290 (3110) 1720 (2330) 2860 (3880)
5.500 139,7) 14.00 K-55 ST&C 1890 (2560) 1420 (1920) 2360 (3200)
5.500 139,7) 15.50 K-55 ST&C 2220 (3000) 1660 (2250)
2770 (3750)
5.500 139,7) 17.00 K-55 ST&C 2520 (3410) 1890 (2560)
3150 (4260)
5.500 (139,7) 15.50 J-55 LT&C 2170 (2940) 1630 (2210) 2710
3680)
5.500 (139,7) 17.00 J-55 LT&C 2470 (3340) 1850 (2510)
3080 4180)
5.500 (139,7) 15.50 K-55 LT&C 2390 (3240) 1790 (2430)
2990 4050)
5.500 (139,7) 17.00 K-55 LT&C 2720 (3680) 2040 (2760)
3390 4600)
5.500 (139,7) 17.00 c-75 LT&C 3270 (4440) 2460 (3330)
4090 5550)
5.500 (139,7) 20.00 c-75 LT&C 4030 (5460) 3020 (4100)
5040 6830)
5.500 (139,7) 23.00 c-75 LT&C 4730 (6410) 3550 (4810)
5910 (8020)
17.00 LT&C 3410 (4630) 2560
5.500 (139,7) L-80 (3470) 4270 (5790)
20.00 L-80 LT&C 4200 (5700) 3150 (4270)
5.500 (139,7) 5250 (7120)
5.500 (139,7) 23.00 LT&C 4930 (6690) 3700 (5020)
L-80 6170 (8360)
3480 (4710) 2610
5.500 139.7) 17.00 N-80 LT&C (3530) 4340 (5890)
LT&C 4280 (5800) 3210
5.500 139,7) 20.00 N-80 (4350) 5350 (7250)
23.00 LT&C 5020 (6810) 3770
5.500 139,7) N-80 (5110) 6280 (8510)
3750 (5090)
5.500 139,7) 17.00 c-90 LT&C 2820 (3820) 4690 (6360)
LT&C 4620 3-170
5.500 139.7) 20.00 c-90 (6270) (4700) 5780 (7830)
LT&C 5430 (7360)
5.500 139,7) 23.00 c-90 4070 (5520) 6780 (9190)
5.500 17.00 c-95 LT&C 3960 (5360) 2970 (4020) 4950 (6710)
20.00 c-95 LT&C 4870 (6600) 3650 (4950) 6090 (8250)
23.00 c-95 LT&C (7750) 4290 (5810) 7150 (9690)
5.500 (139,7 17.00 P-110 LT&C 4620 (6270) 3470 (4700) 5780 (7840)
5.500 (139,7 20.00 P-110 LTSEC 5690 (7720) 4270 (5790) 7110 (9650)
5.500 (139,7 23.00 P-110 LT&C (9060) 5010 (6790) 8350 (11320)
5.500 (139,7) 23.00 Q-125 LT&C 7470 (10120) 5600 (7590) 9330 (12650)
6.625 (168,3) 20.00 H-40 ST&C 1840 (2490) 1380 (1870) 2300 (3120)
6.625 (168,3) 20.00 J-55 ST&C 2450 (3320) 1830 (2490) 3060 (4150)
6.625 (168,3) 24.00 J-55 ST&C 3140 (4250) 2350 (3190) 3920 (5320)
6.625 (168,3) 20.00 K-55 ST&C 2670 (3620) 2000 (2710) 3340 (4520)
6.625 (168.3) 24.00 K-55 ST&C 3420 (4640) 2570 (3480) 4280 (5800)
6.625 (168,3) 20.00 J-55 LT&C 2660 (3600) 1990 (2700) 3320 (4500)
6.625 (168,3) 24.00 J-55 LT&C 3400 (4620) 2550 (3460) 4250 (5770)

IS0 10405:1993(E)
TABLE 1.1 (cont.)
RECOMMENDED CASING MAKE-UP TORQUE
&ROUND-THREAD CASING
1 2 2 4 5 7
NominaI
Size Weight.
Outside Threads Torque, ft-lbs (N-m)
Diameter
and
Coupling Optimum Minimum Maximum
in. (mm) .l bs/ft Grade Thread
6.625 168,3) 20.00 K-55 LT&C 2900 (3940) 2180 (2950) 3630 (4920)
6.625 168.3) 24.00 K-55 LT&C 3720 (5050) 2790 (3780) 4650 (6310)
6.625 168.3) 24.00 c-75 LT&C 4530 (6140) 3390 (4600) 5660 (7670)
168,3) 28.00 c-75 LT&C 5520 (7480) 4140 (5610) 6890 (9350)
6.625
32.00 c-75 LT&C 6380 (8650) 4780 (6490) 7970 10810)
6.625 168,3)
24.00 L-80 LT&C 4730 (6410) 3550 (4810) 5910 (8010)
6.625 168,3)
28.00 L-80 LT&C 5760 (7810) 4320 (5860) 7200 (9760)
6.625 168,3)
L-80 LT&zC 6660 (9030) 5000 8330 11290)
6.625 168,3) 32.00 (6780)
24.00 N-80 LT&C 4810 (6520) 3600 (4890) 6010 (8150)
6.625 168,3)
28.00 N-80 LT&C 5860 (7940) 4390 (5960) 7320 (9930)
6.625 168.3)
N-80 LT&C 6780 (9190) 8470
6.625 168,3) 32.00 5080 (6890) 11480)
c-90 LT&C 5210 (7060) 3910 6510 (8830)
6.625 168,3) 24.00 (5300)
28.00 c-90 LT&C 6350 (8610) 4760 7930 10760)
6.625 (168,3) (6450)
c-90 LT&C 7340 (9950) 9180 12440)
6.625 (168.3) 32.00 5510 (7470)
c-95 LT&C 5490 (7440) 4120 (5580) 6860
6.625 (168,3) 24.00 (9300)
c-95 LT&C 6690 (9070) 5020 (6800) 8360 11340)
6.625 (168,3) 28.00
LT&C 7740 (10490)
6.625 (168,3) 32.00 c-95 5800 (7870) 9670 13110)
P-110 LT&C 6410 (8690) 4810 (6520) 8010
6.625 (168,3) 24.00 (10860)
P-110 LT&C 7810 (10590) 5860 (7940) 9760 (13240)
6.625 (168,3) 28.00
P-110 LT&C 9040 (12250) 6780 (9190)
6.625 (168,3) 32.00 11290 (15310)
Q-125 LT&C 10110 (13710) 7580 (10280) 12640 (17130)
6.625 (168,3) 32.00
1220 (1650) 910 (1240) 1520 2070)
7.000 177,8) 17.00 H-40 ST&C
1760 (2380) 1320 (1790) 2200 2980)
7.000 177,8) 20.00 H-40 ST&C
2340 (3170) 1750 (2380) 2920 3960)
7.000 177,8) 20.00 J-55 ST&C
2840 (3850) 2130 3550
7.000 177,8) 23.00 J-55 ST&C (2890) 4820)
3340 (4530) 2500 (3400) 4170 5660)
177,8) 26.00 J-55 ST&C
7.000
2540 (3450) 1910 3180 4310)
177,8) 20.00 K-55 ST&C (2590)
7.000
7.000 23.00 K-55 ST&C 3090 (4190) 2320 (3150) 3870 (5240)
WV9
2730 4540 (6160)
26.00 K-55 ST&C 3640 (4930) (3700)
7.000 (177,8)
3910 (5300)
23.00 J-55 LT&C 3130 (4240) 2350 (3180)
7.000
J-55 LT&C 3670 (4980) 2760 (3740) 4590 (6230)
7.000 26.00
K-55 LT&C 3410 (4630) 2560 (3470) (5780)
7.000 23.00
(6800)
26.00 K-55 LT&C 4010 (5440) 3010 (4080) 5010
7.000
23.00 c-75 LT&C 4160 (5640) 3120 (4230) 5200 (7050)
7.000 WV)
c-75 LT&C 4890 (6630) 3670 (4970) 6110 (8280)
7.000 26.00
U77,8)
c-75 LT&C 5620 (7620) 4220 (5720) 7030 (9530)
7.000 (177,8) 29.00
32.00 c-75 LT&C 6330 (8580) 4750 (6440) 7910 10730)
7.000 (1773)
c-75 LT&C 7030 (9530) 5270 (7140) 8780 11910)
7.000 35.00
(177,8)
c-75 LT&C 7670 10400) 5750 (7800) 9580 12990)
7.000 38.00
(17X8)
L-80 LT&C 4350 (5890) 3260 (4420) 5430 (7370)
7.000 (177,8) 23.00
L-80 LT&C 5110 (6930) 3830 (5190) 6380 (8660)
7.000 26.00
(177,8)
L-80 LT&C 5870 (7960) 4410 (5970) 7340 (9960)
7.000 29.00
(177,8)
LT&C 6610 (8970) 4960 (6720) 8270 (11210)
7.000 32.00 L-80
(17X8)
L-80 LT&C 7340 (9950) 5510 (7470) 9180 (12440)
7.000 35.00
(177.8)
L-80 LT&C 8010 10860) 6010 (8150) 10010 (13580)
7.000 38.00
(177,8)
IS0 10405:1993(E)
TABLE 1.1 (cont.)
RECOMMENDED CASING MAKE-UP TORQUE
&ROUND-THREAD CASING
1 2 2 4 5 6 7
NominaI
Size Weight,
Torque, ft-lbs (X*m)
Outside Threads
Diameter and
Optimum Iv1 inimum Maximum
Coupling
Thread
in. .I bs/ft Grade
(mm)
4420 (5990)
7.000 W’W 23.00 N-80 LT&C 3310 (4490) 5520 (7490)
5190 (7040)
7.000 26.00 N-80 LT&C 3890 (5280) 6490 (8800)
WV9
5970 (8100)
7.000 29.00 N-80 LT&C 4480 (6070) 7460 10120)
(17X8)
7.000 32.00 N-80 LT&C 6720 (9110) 5040 (6840) 8400 11390)
(17VU
7.000 35.00 N-80 LT&C 7460 10120) 5600 (7590) 9330 12650)
WV)
7.000 38.00 N-80 LT&C 8140 11040) 6110 (8280) 10180 13800)
WV9
7.000 23.00 c-90 LT&C 4790 (6500) 3590 (4870) 5990 8120)
WW
7.000 26.00 c-90 LT&C 5630 (7630) 4220 (5730) 7040 9540)
UW9
7.000 29.00 c-90 LT&C 6480 (8780) 4860 (6590) 8100 0980)
WV)
7.000 32.00 c-90 LT&C 7290 (9880) 5470 (7410) 9110 2360)
(1778
7.000 35.00 c-90 LT&C 8090 10970) 6070 (8230) 10120 3720)
(1773
7.000 38.00 c-90 LT&C 8830 11970) 6620 (8980) 11040 4970)
(177,8)
7.000 23.00 c-95 LT&C 5050 (6850) 3790 (5140) 6310
U77,8)
c-95 LT&C 5930 (8050) 4450 6030) 7420
7.000 W7A9 26.00 10060)
c-95 LT&C 6830 (9250) 5120 6940) 8530
7.000 U77,8) 29.00 11570)
c-95 LT&C 7680 10420) 5760 7810) 9600
7.000 077,8) 32.00 13020)
LT&C 8530 11560) 6400
7.000 (17X8) 35.00 c-95 8670) 10660 14460)
LT&C 9310 12620) 6980
7.000 38.00 c-95 9470) 11640 15780)
W7,8)
P-110 LT&C 6930 (9390) 5200
7.000 WV) 26.00 7050) 8660 11740)
7.000 29.00 P-l 10 LT&C 7970 10800) 7980 8100) 9960 13510)
WV)
7.000 32.00 P-l 10 LT&C 8970 (12160) 6730 (9120) 11210 (15200)
WL8)
7.000 (17W 35.00 P-l 10 LT&C 9960 (13500) 7470 (10130) 12450 (16880)
7.000 38.00 P-110 LT&C 10870 (14730) 8150 (11050) 13580 (18420)
UWU
7.000 35.00 Q-125 LT&C 11150 (15110) 8360 (11340) 13930 (18890)
(17%8)
LT&C
7.000 38.00 Q-125 12160 (16490) 9120 (12370) 15210 (20620)
(17W
7.625 (193,7) 24.00 H-40 ST&C 2120 (2870) 1590 (2150 2640 (3590)
7.625 (193,7) 26.40 J-55 ST&C 3150 (4270) 2360 (3200 3940 (5340)
>
7.625 (193,7) 26.40 K-55 ST&C 3420 (4-640) 2570 (3480 4280 (5800)
>
7.625 (193,7) 26.40 J-55 LT&C 3460 (4690) 2600 (3520 4330 (5870)
)
7.625 193,7) 26.40 K-55 LT&C 3770 (5110) 2820 (3830 4710 (6380)
7.625 26.40 c-75 LT&C 4610 (6250) 3460 (4690 5760 (7810)
193,7)
7.625 193,7) 29.70 c-75 LT&C 5420 (7340) 4060 (5510 6770 (9180)
7.625 193,7) 33.70 c-75 LT&C 6350 (8610) 4760 (6460 7940 (10760)
39.00 C-75 LT&C 7510 (10190) 5640 (7640 9390 (12730)
7.625 193,7)
193,7) 42.80 c-75 LT&C 8520 (11560) 6390 (8670 10660 (14450)
7.625
193.7) 47.10 c-75 LT&C 9530 12920) 7150 (9690) 11910 16150)
7.625 ( (
L-80 LT&C 4820 (6530) 3610 (4900) 6020 (8170)
7.625 193,7) 26.40
L-80 LT&C 5670 (7680) 4250 (5760) 7080 (9600)
7.625 193,7) 29.70
L-80 LT&C 6640 (9000) 4980 (6750) 8300 11250)
7.625 193,7) 33.70
L-80 LT&C 7860 10650) 5890 (7990) 9820 13320)
7.625 193,7) 39.00
L-80 LT&C 8910 12090) 6690 (9060) 11140 15110)
7.625 193,7) 42.80
L-80 LT&C 9970 13520) 7480 10140 12460 16890)
7.625 193,7) 47.10
LT&C 4900 (6640) 3670 (4980 6120
7.625 (193,7) 26.40 N-80 (8300)
LT&C 5750 (7800) 4320 (5850
7.625 (193,7) 29.70 N-80 7190 (9750)
LT&C 6740 (9140) 5060 (6860 8430 (11430)
7.625 (193,7) 33.70 N-80
7.625 (193,7) 39.00 N-80 LT&C 7980 10820) 5990 (8120 9980 (13530)
9060 12280)
7.625 (193,7) 42.80 N-80 LT&C 6790 (9210 11320 (15350)
10130 13730) 7590 10300
7.625 (193,7) 47.10 N-80 LT&C 12660 (17160)

IS0 10405:1993(E)
TABLE 1.1 (cont.)
RECOMMENDED CASING MAKE-UP TORQUE
&ROUND-THREAD CASING
2 2 4 5 6 7
l-
Nominal
Size Weight,
Torque. ft-lbs (Km)
Outside Threads
Diameter and
Maximum
Coupling Optimum &I inimum
in. 4 bs/ft Grade Thread
(mm)
7.625 26.40 c-90 LT&C
(193,7) 5320 (7210) 3990 (5410) 6650 (9010)
7.625 29.70 c-90 LT&C
ww) 6250 (8470) 4690 (6360) 7810 (10590)
7.625 33.70 c-90 LT&C
(193.7) 7330 (9930) 5490 (7450) 9160 (12420)
7.625 39.00 c-90 LT&C
W&7) 8670 (11750) 6500 (8820) 10840 (14690)
42.80 c-90 LT&C
7.625 (19397~ 9840 (13330) 7380 (10000) 12290 ( 16670)
7.625 45.30 c-90 LT&C 10450 (14160) 7840
(19397) (10620) 13060 (17710)
7.625
47.10 c-90 LT&C 13750
(19397) 11000 (14910) 8250 (11180) 18640)
7.625 c-95
26.40 LT&C 4200 (5700) 7010
w%v 5600 (7600) (9500)
7.625 (193,7) 29.70 c-95 LT&C
6590 (8930) 4940 (6700) 8230 11160)
7.625 33.70 c-95 LT&C
(19397) 7720 (10470) 5790 (7850) 9650 13090)
LT&C
7.625 39.00 c-95 6850 (9290) 11420
(19397) 9140 (12390) 15480)
7.625 42.80 c-95 LT&C
(193,7) 10370 (14050) 7770 (10540) 12960 17570)
7.625 47.10 c-95 LT&C 11590 (15720) 8690 (11790)
ww 14490 (19640)
7.625 29.70 P-110 LT&C 7690 (10420) 5770 (7820)
(19397) 9610 (13030)
7.625 33.70 P-110 LT&C 9010 (12220) 6760 (9160)
(193,7) 11260 (15270)
7.625 (193,7) 39.00 P-l 10 LT&C 10660 (14460) 8000 (10840)
13330 (18070)
7.625 w&7) 42.80 P-110 LT&C 12100 (16400) 9070 (12300)
15120 (20510)
7.625 47.10 P-110 LT&C 13530 (18340) 10150 (13760)
(193,7) 16910 (22930)
7.625 (19397) 39.00 Q-125 LT&C 11940 (16190) 8960 (12150)
14930 (20240)
7.625 (19397) 42.80 Q-125 LT&C 13550 (18370) 10160 (13780) 16940 (22970)
7.625 45.30 Q-125 LT&C 14390 (19520) 10800 (14640)
(19397) 17990 (24390)
7.625 47.10 Q-125 LT&C 15150 (20540) 11360 (15410)
ww 18940 (25680)
8.625 (219,l) 28.00 H-40 ST&C 2330 (3150) 1740 (2370)
2910 (3940)
8.625 (219,l) 32.00 H-40 ST&C 2790 (3780) 2090
(2840) 3490 (4730)
8.625 (219,l) 24.00 J-55 ST&C 2440 (3310) 1830 (2480)
3050 (4140)
8.625 (219,1) 32.00 J-55 ST&C 3720 (5050) 2790 (3790)
4660 (6310)
8.625 (219,l) J-55 ST&C 4340 (5880) 3250
36.00 (4410) 5420 (7350)
8.625 (219,l K-55 ST&C 2630 (3570) 1970
24.00 (2680) 3290 (4460)
8.625 (219,l K-55 ST&C 4020 (5460) 3020
.I 32.00 (4090) 5030 (6820)
ST&C 4680 (6350)
8.625 (219,l 36.00 K-55 3510 (4760) 5850 (7940)
LT&C 4170
8.625 (219,l 32.00 J-55 (5660) 3130 (4240) 5220 (7070)
8.625 (219,l LT&C 4860 (6590) 3640
36.00 J-55 (4940) 6070 (8230)
8.625 (219,l 32.00 K-55 LT&C 4520 (6130) 3390 (4600) 5650 (7660)
LT&C
8.625 (219,l) 36.00 K-55 5260 (7140) 3950 (5350) 6580 (8920)
LT&C 6480
8.625 (219,l) 36.00 c-75 (8780) 4860 (6590) 8100 10980)
8.625 (219,l) 40.00 c-75 LT&C 7420 (10060) 5560 (7540) 9270 12570)
8.625 (219.1) 44.00 c-75 LT&C 8340 (11310) 6260 (8490) 10430 14140)
LT&C 7040
8.625 (219,l) 49.00 c-75 9390 (12730) (9550) 11730 15910)
8.625 (219,l 36.00 L-80 LT&C 6780 (9190) 5090 (6900) 8480 (11490)
8.625 (219,l 40.00 L-80 LT&C 7760 (10530) 5820 (7900) 9710 (13160)
LT&C
8.625 (219,l 44.00 L-80 8740 (11840) 6550 (8880) 10920 (14800)
8.625 (219,l 49.00 L-80 LT&C 9830 (13320) 7370 (9990) 12280 (16650)
8.625 (219,l 36.00 N-80 LT&C 6880 (9330) 5160 (7000) 8600 (11660)
8.625 (219,l 40.00 N-80 LT&C 7880 (10680) 5910 (8010) 9850 (13360)
8.625 (219,l) 44.00 N-80 LT&C 8870 (12020) 6650 (9020) 11080 (15030)
8.625 (219,l) 49.00 N-80 LT&C 9970 (13520) 7480 10140) 12470 (16900)
8.625 (219,l) 36.00 c-90 LT&C 7490 (10150) 5620 (7620) 9360 (12690)
8.625 (219,l) 40.00 c-90 LT&C 8580 (11630) 6430 (8720) 10720 (14530)
8.625 (219,l) 44.00 c-90 LT&C 9650 (13080) 7240 (9810) 12060 (16350)
8.625 (219,l) 49.00 c-90 LT&C 10850 (14710) 8140 11040) 13570 (18390)

IS0 10405:1993(E)
TABLE 1.1 (cont.)
RECOMMENDED CASING MAKE-UP TORQUE
&ROUND-THREAD CASING
1, 2 2 4 5 6 7
NominaI
Size Weight,
Outside Threads Torque, ft-Ibs (X-m)
Diameter and
Coupling Optimum hl inimum Maximum
in. 1 bs/ft Grade Thread
(mm)
8.625 (219,l) 36.00 c-95 LT&C 7890
10700) 5920 (8030) 9870 (13380)
8.625 (219,l) 40.00 c-95 LT&C 9040 12260) 6780 (9190) 11300 (15320)
8.625 (219,l) 44.00 c-95 LT&C 10170 13790) 7630 10340) 12710 (17230)
8.625 (219,l) 49.00 c-95 LT&C 11440 15510) 8580 11630) 14300 (19390)
8.625 (219,l) 40.00 P-110 LT&C 10550 14300) 7910 10720) 13180 (17870)
8.625 (219,l) 44.00 P-110 LT&C 11860 16090) 8900 12060) 14830 (20110)
8.625 (219,l) 49.00 P-110 LT&C 13350 (18100) 10010 (13570) 16680 (22620)
8.625 (219,l) 49.00 Q-125 LT&C 14960 (20280) 11220 (15210) 18700 (25350)
9.625 32.30 H-40 ST&C 2540 (3440) 1900 (2580) 3170
(2445) (4300)
9.625 36.00 H-40 ST&C 2940 (3990) 2210 (2990)
(2445) 3680 (4990)
9.625 36.00 J-55 ST&C 3940 (5340) 2950 4000) 4920
W&5) (6670)
9.625 40.00 J-55 ST&C 4520 (6120) 3390 4590) 5650
(2445) (7660)
9.625 36.00 K-55 ST&C 4230 (5740) 3180
(2445) 4310) 5290 (7180)
9.625 40.00 K-55 ST&C 4860 (6590) 3640 4940)
(2445) 6070 (8240)
9.625 36.00 J-55 LT&C 4530 (6140) 3400
(2445) 4610) 5660 (7680)
9.625 J-55 LT&C 5200 7050)
(2445) 40.00 ( 3900 5290) 6500 (8810)
9.625 36.00 K-55 LT&C 4890
(244.5) 6630) 3670 4970) 6110 (8290)
9.625 40.00 K-55 LT&C 5610 7610) 4210
(2445) 5710) 7020 (9510)
LTScC 6940
9.625 (2445) 40.00 C-75 9410) 5200 7060) 8670 11760)
9.625 LT&C 7760 (
WL5) 43.50 c-75 0530) 5820 7890) 9700 13160)
9.625 47.00 c-75 LT&C 8520 ( 1550) 6390
(2445) 8660) 10650 14440)
53.50 LT&C
9.625 (244.5) c-75 9990 (13540) 7490 (10160) 12490 16930)
9.625 (244,s) 40.00 LT&C 7270 (9860)
L-80 5450 (7390) 9090 12320)
9.625 43.50 L-80 LT&C 8130 (11030)
(2-M) 6100 (8270) 10170 13790)
LT&C
9.625 (2445) 47.00 L-80 8930 (12100) 6690 (9080) 11160 15130)
L-80 LT&C 10470 (14190)
9.625 (244,5) 53.50 7850 (10640) 13080 17740)
LT&C 7370
9.625 (2445) 40.00 N-80 10000) 5530 (7500 9220 12500)
9.625 (234,5) 43.50 N-80 ET&C 8250 11190) 6190 (8390 10310 13980)
9.625 (244,s) 47.00 N-80 LT&C 9050 12270) 6790 (9200 11320 15340)
N-80 LT&C
9.625 (2445) 53.50 10620 14390) 7960 (10790 13270 17990)
.
9.625 (2445) 40.00 c-90 LT&C 8040 10900) 6030 10050 13620)
9.625 (2445) 43.50 c-90 LT&C 8990 12190) 6740 11240 15240)
LT&C
9.625 (2445) 47.00 c-90 9870 13380) 7400 12330 16720)
9.625 53.50 c-90 LT&C 11570 (15690) 8680 14460 19610)
(2445)
9.625 40.00 c-95 LT&C 8470 (11490) 6360 (8620) 10590 14360)
(2445)
9.625 43.50 c-95 LT&C 9480 (12850) 7110 (9640) 11850 16060)
(2445)
9.625 47.00 c-95 LT&C 10400 (14100) 7800 10580) 13000 17630)
W45)
9.625 53.50 c-95 LT&C 12200 (16540) 9150 12400) 15250 20670)
(2445)
9.625 (244,5) 43.50 P-110 LT&C 11050 (14980) 8290 (11240) 13810 (18730)
9.625 47.00 P-110 LT&C 12130 (16440) 9090 (12330) 15160 (20550)
(2445)
9.625 53.50 P-110 LT&C 14220 (19280) 10670 (14460) 17780 (24100)
(2445)
LT&C
9.625 47.00 Q-125 13600 (18440) 10200 (13830) 17000 (23050)
(2445)
9.625 53.50 Q-125 LT&C 15950 (21620) 11960 (16220) 19940 (27030)
(2445)
IS0 10405:1993(E)
TABLIS 1.1 (cont.)
RECOMMENDED CASING MAKE-UP TORQUE
&ROUND-THREAD CASING
1 2 2 5 6 7
NominaI
Size Weight.
Outside Threads Torque. ft-Ibs (X-m)
Diameter and
Coupling Optimum hf inimum Maximum
Grade Thread
in. .I bs/ft
(mm)
ST&C 2050 (2790) 1540
32.75 H-40 (2090) 2570 (3480)
10.750 (27391
3140 (4250)
10.750 (273,l 40.50 H-40 ST&C 2350 (3190) 3920 (5320)
10.750 (273,l J-55 ST&C 4200 (5700) 3150 (4270) 5250 (7120)
40.50
J-55 ST&C 4930 (6680) 3700 (5010) 6160 (8360)
10.750 (273.1 45.55
J-55 ST&C 5650 (7660) 4240 (5750) 7070
10.750 (273,l 51.00 (9580)
K-55 ST&C 4500 6100) 3380
10.750 (273,l 40.50 (4580) 5630 (7630)
K-55 ST&C 5280 7160) 3960 (5370)
10.750 (273,l) 45.55 6600 (8960)
51.00 K-55 ST&C 6060 8210) 4540 (6160)
10.750 (273S) 7570 10270)
c-75 ST&C 7560 ( 0250) 5670
10.750 (27391) 51.00 (7690) 9450 12810)
55.50 c-75 ST&C 8420 ( 1420) 6320 (8560)
10.750 WW 10530 14270)
10.750 51.00 L-80 ST&C 7940 ( 0760) 5950 (8070)
(273J) 9920 13450)
10.750 55.50 L-80 ST&C 8840 ( 1990) 6630
W&l) (8990) 11050 14980)
10.750 51.00 N-80 ST&C 8040 (10900) 6030
WV) (8170) 10050 13620)
10.750 55.50 N-80 ST&C 8950 (12140) 6710
(2% 1) (9100) 11190 15170)
10.750 51.00 c-90 ST&C 8790 (11920) 6590
WW (8940) 10990 14890)
10.750 55.50 c-90 ST&C 9790 (13270) 7340
(2733 (9950) 12240 16590)
10.750 (273,l c-95 ST&C 9270 (12560) 6950
.I 51.00 11580 15700)
(273,l c-95 ST&C 10320 (13990) 7740
10.750 55.50 12900 (17490)
.I
P-110 ST&C 10790 (14630)
10.750 (273,l 51.00 8090 10970) 13490 (18290)
(273.1 P-110 ST&C 12020 (16300) 9020
10.750 55.50 12220) 15030 (20370)
P-110 ST&C 13370
10.750 (273,l 60.70 (18130) 10030 13600) 16720 (22660)
P-110 ST&C 14710
10.750 (273,l 65.70 (19950) 11030 14960) 18390 (24930)
(273.1 Q-125 ST&C 15020 (20360) 11260
10.750 60.70 15270) 18770 (25460)
10.750 (273,I 65.70 Q-125 ST&C (22400) 20650 (28000)
ST&C 3070 (4170)
11.750 (298,5) 42.00 H-40 2310 (3130) 3840 (5210)
11.750 (298,5) 47.00 J-55 ST&C 4770 (6460) 3570 (4850) 5960 (8080)
11.750 (298,5) 54.00 J-55 ST&C 5680 (7700) 4260 (5770) 7100 (9620)
11.750 (298,5) 60.00 J-55 ST&C 6490 (8800) 4870 (6600) 8110 (11000)
11.750 (298,5) 47.00 K-55 ST&C 5090 (6900) 3820 (5180) 6360 (8630)
11.750 (298,5) 54.00 K-55 ST&C 6060 (8220) 4550 (6170) 7580 (10280)
11.750 (298,5) 60.00 K-55 ST&C 6930 (9400) 5200 (7050) 8660 (11750)
11.750 (298,5) 60.00 c-75 ST&C 8690 (11780) 6520 (8830) 10860 (14720)
11.750 (298,5) 60.00 L-80 ST&C 9130 (12370) 6840 (9280) 11410 (15470)
11.750 (298,5) 60.00 N-80 ST&C 9240 (12420) 6930 (9390) 11550 (15650)
11.750 (298,5) 60.00 c-90 ST&C 10110 (13710) 7590 10290) 12640 (17140)
11.750 (298,5) 60.00 c-95 ST&C 10660 (14460) 8000 10840) 13330 (18070)
11.750 (298,5) 60.00 P-110 ST&C 12420 (16830) 9310 12630) 15520 (21040)
11.750 (298,5) 60.00 Q-125 ST&C 13950 (18920) 10470 (14190) 17440 (23650)
13.375 (339,7) 48.00 H-40 ST&C 3220 (4370) 2420 (3280) 4030 (5460)
5140 (6970) 3860 (5230) 6430 (8710)
13.375 (339,7) 54.50 J-55 ST&C
J-55 ST&C 5950 (8070) 4460 (6050) 7440 (10090)
13.375 (339,7) 61.00
68.00 J-55 ST&C 6750 (9160) 5070 (6870) 8440 (11450)
13.375 (339,7)
IS0 10405:1993(E)
TABLE 1.1 (cont.)
RECOMMENDED CASING MAKE-UP TORQUE
S-ROUND-THREAD CASING
4 5 6 7
1 2 2
NominaI
Size Weight.
Torque, ft-Ibs (N-m)
Outside Threads
Diameter and
Maximum
Optimum Minimum
Coupling
Thread
in. (mm) Ibs/ft Grade
13.375 (339,7) 54.50 K-55 ST&C 5470 (7410) 4100 (5560) 6840 9270)
(
13.375 (339,7) 61.00 K-55 ST&C 6330 (8580) 4750 (6440) 7910 0730)
(1
13.375 (339,7) 68.00 K-55 ST&C 7180 (9740) 5390 (7300) 8980 2170)
(1
13.375 (339,7) 68.00 c-75 ST&C 9060 12280) 6790 (9210) 11320
5350)
(1
13.375 (339,7) 72.00 c-75 ST&C 9780 13260) 7340 (9950) 12230 6580)
(1
13.375 339,7) 68.00 L-80 ST&C 9520 7140 (9680)
11900 16140)
(
13.375 339,7) 72.00 L-80 ST&C 10290 7720 10460)
12860 17440)
(
339,7) 68.00 N-80 ST&C 9630 13060) 7220 (9790) 12040
13.375 16320)
(
339,7) 72.00 N-80 ST&C 10400 14110) 7800
13.375 10580) 13010 17630)
(
339,7) 68.00 c-90 ST&C 10570 14330) 7930
13.375 10750) 13210 17910)
(
339,7) ST&C 11420 15480) 8560 11610)
13.375 72.00 c-90 14270 19350)
(
ST&C
13.375 (339,7) 68.00 c-95 11140 (15110) 8360 (11330) 13930 (18880)
ST&C
13.375 (339,7) 72.00 c-95 12040 (16320) 9030 (12240) 15050 (20400) ’
ST&C
13.375 (339,7) 68.00 P-l 10 12970 (17580) 9720 (13190) 16210 (21980)
13.375 (339,7) 72.00 P-110 ST&C 14010 (18990) 10510 (14240) 17510 (23740)
ST&C
13.375 (339,7) 72.00 Q-125 15770 (21370) 11820 (16030) 19710 (26720)
16.000 (406,4) 65.00 H-40 ST&C 4390 (5950) 3290 (4460) 5490 (7440)
16.000 (406,4) 75.00 J-55 ST&C 7100 (9630) 5330 (7220) 8880 (12040)
16.000 (406,4) 84.00 J-55 ST&C
8170 (11080) 6130 (8310) 10220 (13850)
16.000 (406,4) 75.00 K-55 ST&C 7520 (10190) 5640 (7640) 9390 (12740)
16.000 (406,4)
84.00 K-55 ST&C 8650 (11730) 6490 (8800) 10810 (14660)
18.625 (473,0) 87.50 H-40 ST&C 5590 (7580) 4200 (5690) 6990 (9480)
18.625 (473,0) 87.50 J-55 ST&C 7540 (10220) 5660 (7670) 9430 (12780)
18.625 (473,0) 87.50 K-55 ST&C 7940 (10770) 5960 (8080) 9930 (13460)
20.000 (508,O) 94.00 H-40 ST&C 5810 (7870) 4360 (5910) 7260 (9840)
20.000 (508,O) 94.00 J-55 ST&C 7830 (10620) 5870 (7960) 9790 ( 13270)
20.000 (508.0) 105.50 J-55 ST&C 9130 (12370) 6850 (9280) 11410 (15470)
20.000 (508,O) 133.00 J-55 ST&C 11920 (16160) 8940 (12120) 14900 (20200)
20.000 (508,O)
94.00 K-55 ST&C 8230 (11160) 6170 (8370) 10290 13950)
20.000 (508,O) 106.50 K-55 ST&C 9590 (13000) 7190 (9750) 11990 16260)
20.000 (508,O) 133.00 K-55 ST&C 12520 (16980) 9390 12740) 15660 21230)
(’
20.000 (508,O) 94.00 J-55 LT&C 9070 (12290) 6800 (9220) 11330 15360)
20.000 (508,O) 106.50 J-55 LTISEC 10560 (14320) 7920 10740) 13210 17900)
(’
20.000 (508,O) 133.00 J-55 LT&C 13790 (18700) 10350 14030) 17240 23380)
(
20.000 (508,O) 94.00 K-55 LT&C 9550 (12950) 7160 (9710) 11940 (16180)
20.000 (508,O) 106.50 K-55 LT&C 11130 (15090) 8350 (11310) 13910 (18860)
20.000 (508,O) 133.00 K-55 LT&C 14530 (19700) 10900 (14770) 18160 (24620)
IS0 10405:1993(E)
TABLE 1.2
TORQUE VALUES FOR EXTREMELINE CASING
The torque values listed below are recommended for use in conjunction with close visual examination to be sure the
shoulder closes and to avoid excessive box swelling.
TORQUE, ftalbf (N-m)
Size
J-55 & c-75, L-80, c-95,
Q-125
Outside
K-55 N-80, C-90 P-110
Dia.
In.
Min. Aim Max. Min. Aim Max. Min. Aim Max. Min. Aim Max.
(mm)
5 2500 2700 3000
3000 3200 3500 3500 3700 4000 4000 4200 4500
(127) (3390) (3660) (4070) (4070) (4340) (4750) (4750) (5020) (5420) (5420) (5690) (6100)
5m 2500 2700 3000 3000 3200 3500 3500
3700 4000 4000 4200 4500
(139,7) (3390) (3660) (4070) (4070) (4340) (4750) (4750) (5020) (5420) (5420) (5690) (6100)
66/8 3000
3200 3500 3500 3700 4000 4000 4200 4500 4500 4700
(168,3) (4070) (4340) (4750) (4750) (5020) (5420) (5420) (5690) (6100) (6100) (6370) (6780)
7 3000 3200 3500 3500 3700
4000 4000 4200 4500 4500 4700 5000
(177,8) (4070) (4340) (4750) (4750) (5020) (5420) (5420) (5690) (6100) (6100) (6370) (6780)
75/s 3500 3700 4000 4000 4200
4500 4500 4700 5000 5000 5200 5500
(193,7) (4750) (5020) (5420) (5420) (5690) (6100) (6100) (6370) (6780) (6780) (7050) (7460)
85/S
4000 4200 4500 4500 4700 5000 5000 5200 5500 5500
5700 6000
(219,l) (5420) (5690) (6100) (6100) (6370) (6780) (6780) (7050) (7460) (7460) (7730) (8130)
9518 4500 4700 5000
5000 5200 5500 6000 6200 6500 6500 6700 7000
(244,5) (6100) (6370) (6780) (6780) (7050) (7460) (8130) (8410) (8810) (8810) (9080) (9490)
NOTES:
(1) The outside shoulder is not a sealing surface; serves as a stop only.
(2) Torque values higher than those listed above may be considered under certain conditions, providing bos swelling
does not occur.
(3) Increased axial tension stress due to higher torque values could be excessive for sulfide service.
(4) If the connection does not shoulder when maximum torque is applied, it should be treated as a questionable joint
as provided under Par. 1.16.
(5) Recommended make-up torque values for 273,1 mm (10 W’) are not available due to lack of data.
IS0 10405:1993(E)
TABLE 2.1
RECOMMENDED TUBING MAKE-UP TORQUE
ROUND THREAD TUBING
1 2 2 4 5
6 7
Nominal
Size Weight,
Outside Threads Torque, ft-Ibs (N-m)
Diameter and
Optimum
Coupling Minimum Maximum
Thread
in. (mm) . Ibs/ft Grade
.1.050
( 26,7) 1.14 H-40 NU 140 (190) 100 (140) 170 (240)
1.050
( 26,7) 1.14 J-55 NU 180 (240) 130 (180) 220 (300)
1.050 ( 26,7) 1.14 c-75 NU 230 (320) 180 (240) 290 (400)
1.050
( 26,7) 1.14 L-80 NU 240 (330) 180 (240) 300 (410)
1.050
( 26,7) 1.14 N-80 NU 250 (340) 190 (250) 310 (420)
1.050 ( 26,7) 1.14 c-90 NU 260 (350) 200 (260)
330 (440)
1.050 ( 26,7) 1.20 H-40 EUE 460 (630) 350 (470)
580 (780)
1.050 ( 26,7) 1.20 J-55 EUE 600 (810) 450 (610)
750 (1020)
1.050 ( 26,7) 1.20 c-75 EUE 780 (1060)
590 (800) 980 (1330)
1.050 ( 26,7) 1.20 L-80 EUE 810 (1090) 610
(820) 1010 (1370)
1.050 ( 26,7) 1.20 N-80 EUE 830 (1130) 620 (840)
1040 (1410)
1.050 ( 26,7) 1.20 c-90 EUE 880 (1190)
660 (890) 1100 (1480)
1.315 33,4) 1.70 H-40 NU 210
(280) 160 (210) 260 (350)
1.315 33,4) 1.70 J-55
NU 270 (370) 200 (280) 340 (460)
33,4) 1.70 c-75 NU
1.315 360 (480) 270 (360) 440 (600)
3394) 1.70 L-80 NU
1.315 370 (500) 270 (370) 460 (620)
3394) 1.70 N-80 NU 380
1.315 (510) 280 (380) 470 (640)
3394) 1.70 c-90
1.315 NU 400 (540) 300 (400) 500 (670)
33.4) 1.80 H-40 EUE
1.315 440 (590) 330 (440) 550 (740)
1.315 ( 33,4) 1.80 J-55 EUE
570 (770) 430 (580) 710 (960)
1.315 ( 33,4) 1.80 c-75
EUE 740 (1010) 560 (750) 930 (1260)
1.315 ( 33,4) 1.80 L-80
EUE 760 (1040) 570 (780) 960 (1300)
1.315 ( 33,4) 1.80 N-80
EUE 790 (1070) 590 (800) 980 (1330)
1.315 ( 33,4) 1.80 c-90
EUE 830 ‘(1130) 620 (840) 1040 (1410)
1.315 ( 33,4) 1.72 H-40 IJ 310 (410) 230 (310) 380 (520)
3394) 1.72 J-55
1.315 IJ 400 (540) 300 (400) 500 (670)
1.315 3374) 1.72 c-75 IJ 520 (700) 390 (530) 650 (880)
33,4)
1.315 1.72 L-80 IJ 530 (720) 400 (540) 670 (900)
3394) 1.72 N-80 IJ
1.315 550 (740) 410 (560) 690 (930)
3394)
1.315 1.72 c-90 IJ 580 (780) 430 (590) 720 (980)
1.660 2.30 H-40 NU 270 (360) 200 (270) 340 (450)
42,2)
1.660 ( 42,2) 2.30 J-55 NU 350 (470) 260 (360) 440 (590)
1.660 ( 42.2) 2.30 C-75 NU 460 (620) 340 (470) 570 (780)
1.660 ( 42,2) 2.30 L-80 NU 470 (640) 350 (480) 590 (800)
1.660 2.30 N-80 NU 490 (660) 360 (490) 610 (820)
( 42,2)
1.660 ( 42,2) 2.30 c-90 NU 510 (700) 390 (520) 640 (870)
1.660 ( 42,2) 2.30 H-40 EUE 530 (720) 400 (540) 660 (900)
2.40 J-55 EUE 690 (940) 520 (700) 860 (1170)
1.660 ( 42,2)
2.40 C-75 EUE 910 (1230) 680 (920) 1130 (1540)
1.660 ( 42,2)
2.40 L-80 EUE 940 (1270) 700 (950) 1170 (1590)
1.660 ( 42,2)
2.40 N-80 EUE 960 (1300) 720 (980) 1200 (1630)
1.660 ( 42,2)
2.40 c-90 EUE 1020 (1380) 760 (1040) 1270 (1730)
1.660 ( 42,2)
2.10 H-40 IJ 380 (520) 290 (390) 480 (650)
1.660 ( 42,2)
422) 2.33 H-40 IJ 380 (520) 290
1.660 (390) 480 (650)
422) 2.10 J-55 IJ 500 (680) 370 (510)
1.660 620 (850)
422) 2.33 J-55 IJ 500 (680) 370
1.660 (510) 620 (850)
42.2) 2.33 C-75 IJ 650
1.660 (890) 490 (670) 820 (1110)
422) 2.33 L-80 IJ 680 (920) 510
1.660 (690) 840 (1140)
42.2) 2.33 N-80 IJ 690
1.660 (940) 520 (710) 870 (1180)
422) 2.33 c-90 IJ
1.660 730 (1000) 550 (750) 920 (1240)
IS0 10405:1993(E)
TABLE 2.1 (cont.)
RECOMMENDED TUBING MAKE-UP TORQUE
ROUND THREAD TUBING
2 2 4
1 5 6 7
Nominal
Size Weight,
Outside Threads Torque, ft-lbs (N-m)
Diameter and
Coupling Optimum Minimum
Maximum
in. (mm) . lbs/ft Grade Thread
1.900 ( 48,3) 2.75 H-40
NU 320 (430) (320) 400 (540)
1.900 ( 48,3) 2.75
J-55 NU 410 (420)
(560) 310 520 (700)
1.900 ( 48,3) 2.75 c-75
NU 540 (730) (550)
410 680 (920)
1.900 ( 48,3) 2.75 L-80
NU 560 (760) (570)
420 700 (950)
48,3) 2.75
N-80 NU 570 (580)
(780) 430 720 (970)
1.900
48,3) 2.75
c-90 NU 610 (620)
(830) 460 760 (1030)
1.900
48,s) 2.90
H-40 EUE 670 (680)
(910) 500 840 (1130)
1.900
493)
2.90 J-55 EUE (890)
880 (1190) 660 1090 (1480)
1.900
48,3)
2.90 c-75 EUE (1170)
1150 (1560) 860 1440 (1950)
1.900
48,3
2.90 L-80 EUE (1210)
1190 (1610) 890 1490 (2010)
1.900
48,3)
2.90 N-80 EUE (1240)
1220 (1650) 910 1520 (2060)
1.900
1.900 ( 48,3)
2.90 c-90 EUE
1300 (1760) 970 (1320)
1620 (2200)
H-40 IJ 450 (600) 330 (450) 560 (750)
1.900 ( 48,3) 2.40
H-40 IJ 450 (600) 330 (450) 560 (750)
1.900 ( 48,3) 2.76
J-55 IJ 580 (790) 440 (590) 730 (990)
1.900 ( 48,3) 2.40
J-55 IJ 580 (790) 440 (590) 730 (990)
1.900 ( 48,3) 2.76
c-75 IJ 760 (1030) 570 (780) 950 (1290)
1.900 ( 48,3) 2.76
L-80 IJ 790 (1070) 590 (800) 990 (1340)
1.900 ( 48,3) 2.76
N-80 IJ 810 (1100) 610 (820) 1010 (1370)
1.900 ( 48,3) 2.76
c-90 1 j 860 (1160) 640 (870) 1070 (1450)
1.900 ( 483) 2.76
2.063
( 52,4) 3.25 H-40 IJ
570 (770) 430 (580)
710 (960)
2.063 ( 5294)
3.25 J-55 IJ
740 (1010) 560
(750) 930 (1260)
2.063 ( 52,4)
3.25 c-75 IJ
970 (1320) 730 (990)
1220 (1650)
2.063 ( 52,4)
3.25 L-80 IJ 1010
(1370) 760 (1020)
1260 (1710)
2.063 ( 52,4)
3.25 N-80 IJ
1030 (1400) 770 (1050)
1290 (1750)
2.063 ( 52,4)
3.25 c-90 IJ
1100 (1490) 820 (1120)
1370 (1860)
IS0 10405:1993(E)
TABLE 2.1 (cont.)
RECOMMENDED TUBING MAKE-UP TORQUE
ROUND THREAD TUBING
1 2 2 5 6 7
2.375 ( 60,3) 4.00 H-40 NU 470 350 (480 580 790)
630)
700 950)
2.375 ( 60,3) 4.60 H-40 NU 560 420 (570
(760)
460 (620
2.375 ( 60,3) 4.00 J-55 NU 610 760 ( 040)
(830)
2.375 ( 60,3) 4.60 J-55 NU 730 550 (740 910 ( 240)
(990)
2.375 ( 60,3) c-75 NU (1090) 600 (820 1010 ( 360)
4.00
2.375 ( 60,3) 4.60 c-75 NU 960 (1300) 720 (980 1200 ( 630)
5.80 c-75 NU 1380 (1860) 1030 (1400 1720 ( 330)
2.375 ( 60,3)
1040 (1410)
2.375 4.00 L-80 NU 830 (1130) 620 (8501
( 60,3)
990 (1350) 750 (1010) 1240 (1680)
2.375 ( 60.3) 4.60 L-80 NU
L-80 NU 1420 (1930) 1070
2.375 ( 60,3) 5.80 (1450) 1780 (2410)
2.375 4.00 N-80 NU 850 (1160)
( 60,3) 640 1070 (1450)
(870)
2.375 NU 1020 (1380) (1040) 1270
( 60,3) 4.60 N-80 760 (1730)
1460 (1980) 1090 1820 (2470)
2.375 ( 60,3) 5.80 N-80 NU (1480)
NU 910 (1230) 680 1140 (1540)
2.375 . 4.00 c-90 (920)
NU 1080 (1470) 810 (1100) 1360
2.375 60.3) 4.60 c-90 (1840)
c-90 NU 1550 (2110) 1160 (1580) 1940 (2630)
2.375 603 5.80
2.375 4.60 P-105 NU 1280 (1740) 960 (1300)
...