ISO 1018:2019

Hard coal — Determination of moisture-holding capacity

This document gives reference to ASTM D1412 as a method of determining the moisture-holding capacity of hard coals.

Houille — Détermination de la capacité de rétention d'humidité

General Information

• Status: Withdrawn
• Publication Date: 29-Sep-2019
• ICS: 73.040 - Coals
• Technical Committee: ISO/TC 27/SC 5 - Methods of analysis
• Drafting Committee: ISO/TC 27/SC 5/WG 1 - Moisture, volatile matter and ash
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 27-Nov-2023

Relations

• Revised: ISO 1018:2023 - Coal — Determination of moisture-holding capacity
• Effective Date: 27-May-2023
• Revises: ISO 1018:1975 - Hard coal — Determination of moisture-holding capacity
• Effective Date: 02-Sep-2017

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 1018
Second edition
2019-09
Hard coal — Determination of
moisture-holding capacity
Houille — Détermination de la capacité de rétention d'humidité
Reference number
ISO 1018:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 1018:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 1018:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Sampling . 1
5 Principle . 1
Bibliography . 2
© ISO 2019 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 1018:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 27, Solid mine
...