ISO 8106:2004
(Main)Glass containers — Determination of capacity by gravimetric method — Test method
Glass containers — Determination of capacity by gravimetric method — Test method
ISO 8106:2004 specifies a gravimetric method for determining the capacity of glass containers and their compliance with specification limits.
Récipients en verre — Détermination de la capacité par la méthode gravimétrique — Méthode d'essai
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 8106
Second edition
2004-11-01
Glass containers — Determination of
capacity by gravimetric method — Test
method
Récipients en verre — Détermination de la capacité par la méthode
gravimétrique — Méthode d'essai
Reference number
ISO 8106:2004(E)
©
ISO 2004
---------------------- Page: 1 ----------------------
ISO 8106:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 8106:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8106 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical
Committee ISO/TC 63, Glass containers, in accordance with the Agreement on technical cooperation between
ISO and CEN (Vienna Agreement).
Throughout the text of this document, read ".this European Standard." to mean ".this International
Standard.".
This second edition cancels and replaces the first edition (ISO 8106:1985), which has been technically
revised.
© ISO 2004 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 8106:2004(E)
Contents page
Foreword.v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Principle.1
5 Sampling.1
6 Apparatus .1
7 Procedure .2
8 Expression of results .2
9 Test report .4
Bibliography .5
iv © ISO 2004 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 8106:2004(E)
Foreword
This document (EN ISO 8106:2004) has been prepared by Technical Committee CEN /TC 261, "Packaging", the
secretariat of which is held by AFNOR, in collaboration with Technical Committee ISO/TC 63 "Glass containers".
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by May 2005, and conflicting national standards shall be withdrawn at the latest by
May 2005.
This document includes a Bibliography.
Efficient packaging is of great importance for the distribution and the protection of goods and the environment.
Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack.
This standard is part of a series of standards for "Glass containers - Test methods":
EN ISO 7458, Glass containers — Internal pressure resistance — Test methods (ISO 7458:2004)
EN ISO 7459, Glass containers — Thermal shock resistance and thermal shock endurance — Test methods
(ISO 7459:2004)
EN ISO 8106, Glass containers — Determination of capacity by gravimetric method — Test method
(ISO 8106:2004)
EN ISO 8113, Glass containers — Resistance to vertical load — Test method (ISO 811
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.