ISO 14135-1:2017
(Main)Optics and photonics — Specifications for telescopic sights — Part 1: General-purpose instruments
Optics and photonics — Specifications for telescopic sights — Part 1: General-purpose instruments
ISO 14135-1:2017 applies to general-purpose telescopic sights, used on hand-held firearms and airguns. It contains a classification to the usage of telescopic sights and specifies interfaces, minimum requirements and tolerances to their performances. High-performance telescopic sights are specified in ISO 14135-2.
Optique et photonique — Spécifications pour lunettes de pointage — Partie 1: Instruments pour usage général
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 14135-1
Third edition
2017-08
Optics and photonics — Specifications
for telescopic sights —
Part 1:
General-purpose instruments
Optique et photonique — Spécifications pour lunettes de pointage —
Partie 1: Instruments pour usage général
Reference number
ISO 14135-1:2017(E)
©
ISO 2017
---------------------- Page: 1 ----------------------
ISO 14135-1:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14135-1:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Interfaces . 2
6 Fundamental requirements . 2
7 Consumer information . 4
7.1 Marking . 4
7.2 Information brochures . 4
7.3 Compliance . 4
Annex A (informative) Recommended interface dimensions . 6
Bibliography . 9
© ISO 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 14135-1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www. iso. org/d irectives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www. iso. org/p atents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o. org/i so/f oreword. html.
This document was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee
SC 4, Telescopic systems.
This third edition cancels and replaces the second edition (ISO 14135-1:2014), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— normative references have been updated;
— example of central tube with inside dovetail has been added.
A list of all parts in the ISO 14135 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 14135-1:2017(E)
Optics and photonics — Specifications for telescopic
sights —
Part 1:
General-purpose instruments
1 Scope
This document applies to general-purpose telescopic sights, used on hand-held firearms and airguns.
It contains a classification to the usage of telescopic sights and specifies interfaces, minimum
requirements and tolerances to their performances.
High-performance telescopic sights are specified in ISO 14135-2.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 14132-1, Optics and photonics — Vocabulary for telescopic systems — Part 1: General terms and
alphabetical indexes of terms in ISO 14132
ISO 14132-3, Optics and photonics — Vocabulary for telescopic systems — Part 3: Terms for telescopic sights
ISO 14490-1, Optics and optical instruments — Test methods for telescopic systems — Part 1: Test methods
for basic characteristics
ISO 14490-3, Optics and photonics — Test methods for telescopic systems — Part 3: Test methods for
telescopic sights
ISO 14490-5, Optics and optical instruments — Test methods for telescopic systems — Part 5: Test methods
for transmittance
ISO 14490-7, Optics and photonics — Test methods for telescopic systems — Part 7: Test methods for limit
of resolution
ISO 20711, Optics and photonics — Environmental requirements — Test requirements for telescopic systems
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 14132-1 and ISO 14132
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.