ISO 14135-1:2014
(Main)Optics and photonics — Specifications for telescopic sights — Part 1: General-purpose instruments
Optics and photonics — Specifications for telescopic sights — Part 1: General-purpose instruments
ISO 14135-1:2014 applies to general-purpose telescopic sights, used on hand-held firearms and airguns. It contains a classification to the usage of telescopic sights and specifies interfaces, minimum requirements, and tolerances to their performances. High-performance telescopic sights are specified in ISO 14135‑2.
Optique et photonique — Spécifications pour lunettes de pointage — Partie 1: Instruments pour usage général
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 14135-1
Second edition
2014-10-01
Optics and photonics — Specifications
for telescopic sights —
Part 1:
General-purpose instruments
Optique et photonique — Spécifications pour lunettes de pointage —
Partie 1: Instruments pour usage général
Reference number
ISO 14135-1:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 14135-1:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14135-1:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
5 Interfaces . 2
6 Fundamental requirements . 2
7 Consumer information . 4
7.1 Marking . 4
7.2 Information brochures . 4
7.3 Compliance . 4
Annex A (informative) Recommended interface dimensions . 6
© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 14135-1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 172, Optics and photonics, Subcommittee SC 4,
Telescopic systems.
This second edition cancels and replaces the first edition (ISO 14135-1:2003) which has been technically
revised.
ISO 14135 consists of the following parts, under the general title Optics and photonics — Specifications
for telescopic sights:
— Part 1: General-purpose instruments
— Part 2: High-performance instruments
iv © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 14135-1:2014(E)
Optics and photonics — Specifications for telescopic
sights —
Part 1:
General-purpose instruments
1 Scope
This part of ISO 14135 applies to general-purpose telescopic sights, used on hand-held firearms and
airguns. It contains a classification to the usage of telescopic sights and specifies interfaces, minimum
requirements, and tolerances to their performances.
High-performance telescopic sights are specified in ISO 14135-2.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 10109-4, Optics and optical instruments — Environmental requirements — Part 4: Test requirements
for telescopic systems
ISO 14132-1, Optics and photonics — Vocabulary for telescopic systems — Part 1: General terms and
alphabetical indexes of terms in ISO 14132
ISO 14132-3, Optics and photonics — Vocabulary for telescopic systems — Part 3: Terms for telescopic sights
ISO 14490-1, Optics and optical instruments — Test methods for telescopic systems — Part 1: Test methods
for basic characteristics
ISO 14490-3, Optics and optical instruments — Test methods for telescopic systems — Part 3: Test methods
for telescopic sights
ISO 14490-5, Optics and optical instr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.