ISO/IEC 16353:2011

Information technology — Telecommunications and information exchange between systems — Front-end configuration command for NFC-WI (NFC-FEC)

ISO/IEC 16353:2011 specifies commands for the Near Field Communication Wired Interface (NFC-WI) specified in ISO/IEC 28361. The commands allow exchange of control and state information between the transceiver and the front-end.

Technologies de l'information — Télécommunications et échange d'informations entre systèmes — Commande à configuration frontale pour NFC-WI (NFC-FEC)

General Information

• Status: Published
• Publication Date: 29-Sep-2011
• ICS: 35.100.10 - Physical layer
• Technical Committee: ISO/IEC JTC 1/SC 6 - Telecommunications and information exchange between systems
• Drafting Committee: ISO/IEC JTC 1/SC 6/WG 1 - Physical and data link layers
• Current Stage: 9060 - Close of review
• Start Date: 02-Sep-2027

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 16353
First edition
2011-10-01


Information technology —
Telecommunications and information
exchange between systems —
Front-end configuration command for
NFC-WI (NFC-FEC)
Technologies de l'information — Télécommunications et échange
d'informations entre systèmes — Commande à configuration frontale
pour NFC-WI (NFC-FEC)




Reference number
ISO/IEC 16353:2011(E)
©
ISO/IEC 2011

---------------------- Page: 1 ----------------------
ISO/IEC 16353:2011(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2011 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 16353:2011(E)
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Conformance . 1
3 Normative references . 1
4 Terms and definitions . 1
5 Conventions and notations . 1
6 Acronyms . 1
7 States . 1
7.1 Escape state . 2
7.2 Command Ready state . 2
7.3 Command Busy state . 2
7.4 Quit state . 2
8 Commands and Responses . 3
8.1 Command and response Format . 3
8.2 Checksum . 3
8.3 Commands . 3
8.4 Responses . 4
9 Information-Transfer . 4
9.1 Transceiver Frames . 4
9.2 Front-end Frames . 4

© ISO/IEC 2011 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 16353:2011(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 16353 was prepared by Ecma International (as ECMA-390) and was adopted, under a special “fast-
track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its
approval by national bodies of ISO and IEC.

iv © ISO/IEC 2011 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 16353:2011(E)
Introduction
ISO/IEC 28361 specifies a two-wire interface for which this International Standard defines commands,
responses and their transmission, allowing the exchange of control and state information between the
transceiver and the front-end as specified in ISO/IEC 28361. Such exchange may include indication of the
presence of the RF field and control information to change data rates and communication modes of the
front-end.


© ISO/IEC 2011 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD
...