Milling machine arbors with 7/24 tapers — Part 1: Dimensions and designation

ISO 839-1:2006 specifies the dimensions of milling machine arbors with 7/24 tapers in accordance with ISO 297. It also specifies the designation of these arbors.

Arbres porte-fraises au cône 7/24 — Partie 1: Dimensions et désignation

L'ISO 839-1:2006 spécifie les dimensions des arbres porte-fraises au cône 7/24 conformément à l'ISO 297. Elle spécifie également la désignation de ces arbres.

General Information

Status
Published
Publication Date
05-Dec-2006
Current Stage
9093 - International Standard confirmed
Completion Date
21-Dec-2020
Ref Project

Relations

Buy Standard

Standard
ISO 839-1:2006 - Milling machine arbors with 7/24 tapers
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 839-1:2006 - Arbres porte-fraises au cône 7/24
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 839-1
Second edition
2006-12-01
Milling machine arbors with 7/24
tapers —
Part 1:
Dimensions and designation
Arbres porte-fraises au cône 7/24 —
Partie 1: Dimensions et désignation
Reference number
ISO 839-1:2006(E)
ISO 2006
---------------------- Page: 1 ----------------------
ISO 839-1:2006(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

© ISO 2006

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 839-1:2006(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 839-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 2, High speed

steel cutting tools and their attachments.

This second edition cancels and replaces the first edition (ISO 839-1:1976), which has been technically

revised.

ISO 839 consists of the following parts, under the general title Milling machine arbors with 7/24 tapers:

⎯ Part 1: Dimensions and designation
⎯ Part 2: Accessories
© ISO 2006 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 839-1:2006(E)
Milling machine arbors with 7/24 tapers —
Part 1:
Dimensions and designation
1 Scope

This part of ISO 839 specifies the dimensions of milling machine arbors with 7/24 tapers in accordance with

ISO 297. It also specifies the designation of these arbors.

NOTE The accessories of these arbors (spacing collars, bearing collars and clamping nuts) are specified in

ISO 839-2.
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.
ISO 297:1988, 7/24 tapers for tool shanks for manual changing
ISO 2768-1:1989, General tolerances — Part 1: Tolerances f
...

NORME ISO
INTERNATIONALE 839-1
Deuxième édition
2006-12-01
Arbres porte-fraises au cône 7/24 —
Partie 1:
Dimensions et désignation
Milling machine arbors with 7/24 tapers —
Part 1: Dimensions and designation
Numéro de référence
ISO 839-1:2006(F)
ISO 2006
---------------------- Page: 1 ----------------------
ISO 839-1:2006(F)
PDF – Exonération de responsabilité

Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier

peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence

autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées

acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute

responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.

Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info

du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir

l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,

veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2006

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit

de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.

ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2006 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 839-1:2006(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée

aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du

comité technique créé à cet effet. Les organisations internationales, gouvernementales et non

gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec

la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,

Partie 2.

La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur

publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres

votants.

L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne

pas avoir identifié de tels droits de propriété et averti de leur existence.

L'ISO 839-1 a été élaborée par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 2, Outils

coupants en acier rapide et leurs attachements.

Cette deuxième édition annule et remplace la première édition (ISO 839-1:1976), qui a fait l'objet d'une

révision technique.

L'ISO 839 comprend les parties suivantes, présentées sous le titre général Arbres porte-fraises au cône 7/24:

⎯ Partie 1: Dimensions et désignation
⎯ Partie 2: Équipements
© ISO 2006 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 839-1:2006(F)
Arbres porte-fraises au cône 7/24 —
Partie 1:
Dimensions et désignation
1 Domaine d'application

La présente partie de l'ISO 839 spécifie les dimensions des arbres porte-fraises au cône 7/24 conformément

à l'ISO 297. Elle spécifie également la désignation de ces arbres portes-fraises.

NOTE Les équipements de ces arbres (bagues d'espacement et de roulement, écrous de blocage) sont spécifiés

dans l'ISO 839-2.
2 Références normatives

Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les

références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du

document de référence s'applique (y compris les éventuels
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.