Flexible cellular polymeric materials — Moulded and extruded sponge or expanded cellular rubber products — Compressibility test on finished parts

This International Standard specifies a method of determining the hardness or compressibility of a material by measuring the compression and/or deformation force on flexible cellular polymeric profiles not less than 3 mm thick.

Matériaux polymères alvéolaires souples — Produits en caoutchouc alvéolaire expansé ou spongieux, moulés et extrudés — Essai de compressibilité sur des produits finis

General Information

Status
Published
Publication Date
25-Oct-2000
Current Stage
9093 - International Standard confirmed
Completion Date
25-Nov-2020
Ref Project

Relations

Buy Standard

Standard
ISO 11752:2000 - Flexible cellular polymeric materials -- Moulded and extruded sponge or expanded cellular rubber products -- Compressibility test on finished parts
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11752
First edition
2000-10-15
Flexible cellular polymeric materials —
Moulded and extruded sponge or expanded
cellular rubber products — Compressibility
test on finished parts
Matériaux polymères alvéolaires souples — Produits en caoutchouc
alvéolaire expansé ou spongieux, moulés et extrudés — Essai de
compressibilité sur des produits finis
Reference number
ISO 11752:2000(E)
©
ISO 2000

---------------------- Page: 1 ----------------------
ISO 11752:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11752:2000(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Principle.1
4 Apparatus .1
5 Test pieces .2
6 Conditioning.2
7 Procedure .2
8 Expression of results .3
9 Test report .3
© ISO 2000 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11752:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 11752 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 4, Products (other than hoses).
iv © ISO 2000 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 11752:2000(E)
Flexible cellular polymeric materials — Moulded and extruded
sponge or expanded cellular rubber products — Compressibility
test on finished parts
WARNING — Persons using this International Standard should be familiar with normal laboratory practice.
This standard does not purport to address all of the safety problems, if any, associated with its use. It is
the responsibility of the user
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.