ISO 7076-6:2024
(Main)Fire protection — Foam fire extinguishing systems — Part 6: Vehicle-mounted compressed air foam systems
Fire protection — Foam fire extinguishing systems — Part 6: Vehicle-mounted compressed air foam systems
This document specifies requirements for compressed air foam systems (CAFS) in which foam concentrate and compressed air are continuously added to the water being discharged from the fire-fighting pump. This document is applicable to CAFS that can be permanently installed in fire-fighting vehicles, or that are transportable or mobile. This document specifies requirements for CAFS which are used at ambient temperatures ranging from –10 °C to +40 °C. This document does not apply to stationary CAFS. This document does not apply to requirements for hazards related to handling foam concentrates, noise generated by CAFS, drives, auxiliary equipment, power sources, or pumps connected to the CAFS. This document does not specify requirements for special hazards arising from particular conditions under which CAFS are used, for example: — immunity against electromagnetic fields and electrostatic discharge; — operation without supervision; — events specific to the location where the CAFS is set up (e.g. on public roads); — handling of any equipment, devices, etc. which have to be connected to the CAFS or are joined to it (e.g. branch pipes, nozzles and pressure hoses); — decommissioning and disposal.
Titre manque — Partie 6: Titre manque
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 7076-6
Second edition
Fire protection — Foam fire
2024-06
extinguishing systems —
Part 6:
Vehicle-mounted compressed air
foam systems
Reference number
ISO 7076-6:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 7076-6:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 7076-6:2024(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 3
4.1 Conformance .3
4.1.1 Type assessments .3
4.1.2 Individual assessments .3
4.2 Safety and protective measures .4
4.2.1 General .4
4.2.2 Mechanical equipment .4
4.2.3 Components under pressure .4
4.2.4 Material, parts and components.5
4.2.5 Hot parts .5
4.2.6 Electrical equipment .5
4.2.7 Operator controls and indicators .5
4.2.8 System failure and continuation of on-going fire-fighting operation .5
4.2.9 Shutdown control .5
4.2.10 Maintenance and service .
...
International
Standard
ISO 7076-6
Second edition
Fire protection — Foam fire
extinguishing systems —
Part 6:
Vehicle-mounted compressed air
foam systems
PROOF/ÉPREUVE
Reference number
ISO 7076-6:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 7076-6:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 7076-6:2024(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 3
4.1 Conformance .3
4.1.1 Type assessments .3
4.1.2 Individual assessments .3
4.2 Safety and protective measures .4
4.2.1 General .4
4.2.2 Mechanical equipment .4
4.2.3 Components under pressure .4
4.2.4 Material, parts and components.5
4.2.5 Hot parts .5
4.2.6 Electrical equipment .5
4.2.7 Operator controls and indicators .5
4.2.8 System failure and continuation of on-going fire-fighting operation .5
4.2.9 Shutdown control .6
4.2.10 Maintenance and service .
...
ISO/DISPRF 7076-6:2023(E)
ISO/TC 21/SC 6/WG 8
Date: 2023-01-10
Secretariat: SAC
Date: 2024-04-22
Fire protection — Foam fire extinguishing systems —
Part 6:
Vehicle-mounted compressed air foam systems
Protection contre l'incendie — Systèmes d'extinction d'in cendie à mousse — Partie 6: Équipement pour
mousse physique à air comprimé monté sur vehicules
PROOF
---------------------- Page: 1 ----------------------
ISO/PRF 7076-6:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/PRF 7076-6:2024(en)
Contents Page
Foreword . v
Introduction . vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 4
4.1 Conformance . 4
4.1.1 Type assessments . 4
4.1.2 Individual assessments . 4
4.2 Safety and protective measures . 5
4.2.1 General . 5
4.2.2 Mechanical equipment . 5
4.2.3 Components under pressure . 5
4.2.4 Material, parts and components . 5
4.2.5 Hot parts . 6
4.2.6 Electrical equipment . 6
4.2.7 Operator controls and indicators . 6
4.2.8 System failure and continuation of on-going fire-fighting operation . 6
4.2.9 Shutdown control . 6
4.2.10 Maintenance and service . 6
4.2.11 Protection against over-speed . 6
4.2.12 Safety from over-heating . 7
4.3 Performance . 7
4.3.1 Operation .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.