ISO 3547-1:2018

Plain bearings — Wrapped bushes — Part 1: Dimensions

This document specifies the dimensions and designations of cylindrical and flanged wrapped bushes made of mono and multi-layer bearing material for plain bearing applications.

Paliers lisses — Bagues roulées — Partie 1: Dimensions

Drsni ležaji - Zvite puše - 1. del: Mere

General Information

• Status: Published
• Publication Date: 09-Jul-2018
• ICS: 21.100.10 - Plain bearings
• Technical Committee: ISO/TC 123/SC 3 - Dimensions, tolerances and construction details
• Drafting Committee: ISO/TC 123/SC 3 - Dimensions, tolerances and construction details
• Current Stage: 9060 - Close of review
• Start Date: 04-Mar-2029
• Ref Project: SIST ISO 3547-1:2020 - Plain bearings - Wrapped bushes - Part 1: Dimensions

Relations

• Revises: ISO 3547-1:2006 - Plain bearings — Wrapped bushes — Part 1: Dimensions
• Effective Date: 19-Dec-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 3547-1:2020
01-oktober-2020
Drsni ležaji - Zvite puše - 1. del: Mere
Plain bearings - Wrapped bushes - Part 1: Dimensions
Paliers lisses - Bagues roulées
Ta slovenski standard je istoveten z: ISO 3547-1:2018
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3547-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 3547-1:2020

---------------------- Page: 2 ----------------------
SIST ISO 3547-1:2020
INTERNATIONAL ISO
STANDARD 3547-1
Third edition
2018-07
Plain bearings — Wrapped bushes —
Part 1:
Dimensions
Paliers lisses — Bagues roulées —
Partie 1: Dimensions
Reference number
ISO 3547-1:2018(E)
©
ISO 2018

---------------------- Page: 3 ----------------------
SIST ISO 3547-1:2020
ISO 3547-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 3547-1:2020
ISO 3547-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 1
5 Dimensions . 2
6 Design . 9
7 Example for calculation of inside diameter, D .10
i
8 Designation .10
Bibliography .11
© ISO 2018 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 3547-1:2020
ISO 3547-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
...

INTERNATIONAL ISO
STANDARD 3547-1
Third edition
2018-07
Plain bearings — Wrapped bushes —
Part 1:
Dimensions
Paliers lisses — Bagues roulées —
Partie 1: Dimensions
Reference number
ISO 3547-1:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 3547-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3547-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 1
5 Dimensions . 2
6 Design . 9
7 Example for calculation of inside diameter, D .10
i
8 Designation .10
Bibliography .11
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3547-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the volunta
...