ISO/TR 21865:2017

Fireworks — Third party testing — Voluntary scheme

ISO/TR 21865:2017 describes the relevant responsibilities of the involved manufacturers of fireworks articles and corresponding laboratories for the application of the ISO 25947 series and the ISO 26261 series. By applying this approach, a clear separation of the responsibilities of the manufacturers and the third party laboratories is achieved in order to demonstrate the conformity to the relevant safety specifications defined in these standards.

Artifices de divertissement — Essais réalisés par des tiers — Essais à caractère non-obligatoire

General Information

• Status: Published
• Publication Date: 26-Oct-2017
• ICS: 71.100.30 - Explosives. Pyrotechnics and fireworks
• Technical Committee: ISO/TC 264 - Fireworks
• Drafting Committee: ISO/TC 264 - Fireworks
• Current Stage: 6060 - International Standard published
• Due Date: 16-Aug-2018
• Completion Date: 27-Oct-2017

Standards Content (Sample)

TECHNICAL ISO/TR
REPORT 21865
First edition
2017-11
Fireworks — Third party testing —
Voluntary scheme
Artifices de divertissement — Essais réalisés par des tiers — Essais à
caractère non-obligatoire
Reference number
ISO/TR 21865:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO/TR 21865:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TR 21865:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Responsibilities and obligations . 2
4.1 Manufacturers . 2
4.2 Laboratories . 2
Bibliography . 3
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TR 21865:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 264, Fireworks.
iv © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
TECHNICAL REPORT ISO/TR 21865:2017(E)
Fireworks — Third party testing — Voluntary scheme
1 Scope
This document describes the relevant responsibilities of the involved manufacturers of fireworks articles
and corresponding laboratories for the application of the ISO 25947 series and the ISO 26261 series.
By applying this approach, a clear separation of the responsibilities of the manufacturers and the
third party laboratories is achieved in order to demonstrate the conformity to the relevant safety
specifications defined in these standards.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for
...