ISO 603-18:2013

Bonded abrasive products — Dimensions — Part 18: Grinding wheels for flat glass edge grinding machines

ISO 603-18:2013 specifies the shapes, dimensions and limit deviations, in millimetres, of grinding wheels for flat glass edge grinding machines. This type of bonded abrasive wheel is intended to be used on stationary machines where the position of the grinding wheel is fixed and the workpiece is guided by hand or guided mechanically, or on a stationary machine where the grinding wheel is guided mechanically and the workpiece is fixed.

Produits abrasifs agglomérés — Dimensions — Partie 18: Meules pour machines à meuler les bords de verre plat

General Information

• Status: Published
• Publication Date: 02-Jan-2013
• ICS: 25.100.70 - Abrasives
• Technical Committee: ISO/TC 29/SC 5 - Grinding wheels and abrasives
• Drafting Committee: ISO/TC 29/SC 5/WG 5 - Bonded abrasives
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 11-Mar-2024

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 603-18
First edition
2013-01-15
Bonded abrasive products —
Dimensions —
Part 18:
Grinding wheels for flat glass edge
grinding machines
Produits abrasifs agglomérés — Dimensions —
Partie 18: Meules pour machines à meuler les bords de verre plat
Reference number
ISO 603-18:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 603-18:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 603-18:2013(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Requirements . 1
3.1 Shapes and dimensions . 1
3.2 Designation . 6
3.3 Specifications. 6
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 603-18:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 603-18 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding
wheels and abrasives.
ISO 603 consists of the following parts, under the general title Bonded abrasive products — Dimensions:
— Part 1: Grinding wheels for external cylindrical grinding between centres
— Part 2: Grinding wheels for centreless external cylindrical grinding
— Part 3: Grinding wheels for internal cylindrical grinding
— Part 4: Grinding wheels for surface grinding/peripheral grinding
— Part 5: Grinding wheels for surface grinding/face grinding
— Part 6: Grinding wheels for tool and tool room grinding
— Part 7: Grinding wheels for manually guided grinding
— Part 8: Grinding wheels for deburring and fettling/snagging
— Part 9: Grinding wheels for high-pressure grinding
— Part 10: Stones for honing and superfinishings
— Part 11: Hand finishing sticks
— Part 12: Grinding wheels for deburring and fettling on a straight grinder
— Part 13: Grinding wheels for deburring and fettling on a vertical grinder
— Part 14: Grinding
...

DRAFT INTERNATIONAL STANDARD ISO/DIS 603-18
ISO/TC 29/SC 5 Secretariat: DIN
Voting begins on Voting terminates on

2011-09-30 2012-03-01
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION    МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ    ORGANISATION INTERNATIONALE DE NORMALISATION


Bonded abrasive products — Dimensions —
Part 18:
Grinding wheels for flat glass edge grinding machines
Produits abrasifs agglomérés — Dimensions —
Partie 18: Meules pour machines à meuler les bords de verre plat
ICS 25.100.70








In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.

To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.



THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©  International Organization for Standardization, 2011

---------------------- Page: 1 ----------------------
ISO/DIS 603-18

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.

ii © ISO 2011 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 603-18
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Requirements.1
3.1 Shapes and dimensions .1
3.1.1 Straight Wheel, Type 1.2
3.1.2 Straight Cup Wheel, Type 6.3
3.1.3 Disc Wheel, cemented, Type 35 .4
3.1.4 Straight Wheel, Type 1 with profile.5
3.2 Designation.7
3.3 Specifications.7
3.3.1 General specification.7
3.3.2 Tolerances.7
3.3.3 Unbalance.
...