ISO 21927-7:2017
(Main)Smoke and heat control systems — Part 7: Smoke ducts sections
Smoke and heat control systems — Part 7: Smoke ducts sections
ISO 21927-7:2017 applies to smoke control duct sections placed on the market and intended to operate as part of a pressure differential system or smoke and heat exhaust system. This document specifies requirements and gives reference to the test methods defined for smoke control duct sections and their associated components (for example, hangers and other items proven at the time of testing), which are intended to be installed in such systems in buildings. Furthermore, marking and information on installation and maintenance of these products are also given in this document. NOTE To avoid duplication, reference is made to a variety of other standards. To this end, this document can be read in conjunction with EN 1366‑8, EN 1366‑9 and ISO 6944‑1, for details of the fire resistance testing and EN 13501‑4 for corresponding classification. ISO 21927-7:2017 has not considered in detail the detrimental and/or corrosive effects that may be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently. ISO 21927-7:2017 also governs associated components used together with smoke control duct sections such as turning vanes and silencers, with the exception of natural and powered smoke ventilators and smoke control dampers, which are covered by separate standards. Ducts for use other than in smoke and heat exhaust/control systems are not covered by this document.
Systèmes pour le contrôle des fumées et de la chaleur — Partie 7: Sections des conduits de désenfumage
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 21927-7
First edition
2017-04
Smoke and heat control systems —
Part 7:
Smoke ducts sections
Systèmes pour le contrôle des fumées et de la chaleur —
Partie 7: Sections des conduits de désenfumage
Reference number
ISO 21927-7:2017(E)
©
ISO 2017
---------------------- Page: 1 ----------------------
ISO 21927-7:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 21927-7:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Smoke control duct section requirements . 3
4.1 General . 3
4.1.1 Fire resistance — multi-compartment smoke control duct section . 3
4.1.2 Fire resistance — single compartment smoke control duct section . 4
4.2 Construction and components: Characteristics . 4
4.2.1 Construction and operation . 4
4.2.2 Structural supports used for smoke control duct sections . 4
4.2.3 Duct sealant materials used in or between smoke control duct sections . 4
4.2.4 Penetration seals between fire compartments . 4
4.2.5 Other components . 5
4.3 Fire resistance performance criteria: Multi-compartment fire resisting smoke
control duct sections . 5
4.3.1 Integrity, insulation, leakage . 5
4.3.2 Fire resistance classification and designation. 6
4.4 Fire resistance performance criteria: Single compartment smoke control duct sections . 6
4.4.1 Integrity, leakage . 6
4.4.2 Fire resistance classification and designation. 6
5 Test methods . 7
5.1 Ambient leakage tests .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.