Tool holders with cylindrical shank — Part 3: Type B with rectangular radial seat

ISO 10889-3:2004 specifies dimensions, designations and complementary technical delivery conditions for tool holders with a rectangular radial seat of types B1 to B8 with cylindrical shank in accordance with ISO 10889-1. It is applicable to tool holders with cylindrical shank for machine tools with non-rotating tools, preferably for turning machines.

Porte-outil à queue cylindrique — Partie 3: Porte-outil radial de type B

L'ISO 10889 est applicable aux porte-outil à queue cylindrique pour machines-outils à outils non rotatifs, en particulier les machines de tournage. L'ISO 10889-3:2004 spécifie les dimensions, la désignation et les conditions techniques de livraison complémentaires des porte-outil radiaux de types B1 à B8, à queue cylindrique conforme à l'ISO 10889-1:2004.

General Information

Status
Withdrawn
Publication Date
17-Nov-2004
Withdrawal Date
17-Nov-2004
Technical Committee
Drafting Committee
Current Stage
9599 - Withdrawal of International Standard
Completion Date
10-Mar-2016
Ref Project

Relations

Buy Standard

Standard
ISO 10889-3:2004 - Tool holders with cylindrical shank
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 10889-3:2004 - Porte-outil a queue cylindrique
French language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10889-3
Second edition
2004-11-15

Tool holders with cylindrical shank —
Part 3:
Type B with rectangular radial seat
Porte-outil à queue cylindrique —
Partie 3: Porte-outil radial de type B




Reference number
ISO 10889-3:2004(E)
©
ISO 2004

---------------------- Page: 1 ----------------------
ISO 10889-3:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10889-3:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10889-3 was prepared by Technical Committee ISO/TC 29, Small tools.
This second edition cancels and replaces the first edition (ISO 10889-3:1997), Table 1 of which has been
technically revised.
ISO 10889 consists of the following parts, under the general title Tool holders with cylindrical shank:
— Part 1: Cylindrical shank, location bore — Technical delivery conditions
— Part 2: Type A, shanks for tool holders of special designs
— Part 3: Type B with rectangular radial seat
— Part 4: Type C with rectangular axial seat
— Part 5: Type D with more than one rectangular seat
— Part 6: Type E with cylindrical seat
— Part 7: Type F with taper seat
— Part 8: Type Z, accessories

© ISO 2004 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 10889-3:2004(E)

Tool holders with cylindrical shank —
Part 3:
Type B with rectangular radial seat
1 Scope
ISO 10889 is applicable to tool holders with cylindrical shank for machine tools with non-rotating tools,
preferably for turning machines.
This part of ISO 10889 specifies dimensions, designations and complementary technical delivery conditions
for tool holders with a rectangular radial seat of types B1 to B8 with cylindrical shank in accordance with
ISO 10889-1. For non-standardized tool holders with a rectangular radial seat such as the tool holders shown
in the figures, it is advisable to apply the corresponding specifications of this part of ISO 10889.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications
ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance
indications
ISO 10889-1, Tool holders with cylindrical shank — Part 1: Cylindrical shank, location bore — Technical
delivery conditions
3 Dimensions
See Figures 1 to 8 and Table 1.
Unspecified details shall be chosen appropriately.
General tolerances: ISO 2768-mH.
© ISO 2004 – All rights reserved 1

----------
...

NORME ISO
INTERNATIONALE 10889-3
Deuxième édition
2004-11-15


Porte-outil à queue cylindrique —
Partie 3:
Porte-outil radial de type B
Tool holders with cylindrical shank —
Part 3: Type B with rectangular radial seat




Numéro de référence
ISO 10889-3:2004(F)
©
ISO 2004

---------------------- Page: 1 ----------------------
ISO 10889-3:2004(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


©  ISO 2004
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2004 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 10889-3:2004(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 10889-3 a été élaborée par le comité technique ISO/TC 29, Petit outillage.
Cette deuxième édition annule et remplace la première édition (ISO 10889-3:1997), dont le Tableau 1 a fait
l'objet d'une révision technique.
L'ISO 10889 comprend les parties suivantes, présentées sous le titre général Porte-outil à queue cylindrique:
— Partie 1: Queue cylindrique, alésage de réception — Conditions techniques de livraison
— Partie 2: Porte-outil de type A de conceptions spéciales
— Partie 3: Porte-outil radial de type B
— Partie 4: Porte-outil axial de type C
— Partie 5: Porte-outil de type D comportant plusieurs logements
— Partie 6: Porte-outil de type E pour outils à queue cylindrique
— Partie 7: Porte-outil de type F pour outils à queue conique
— Partie 8: Accessoires, type Z

© ISO 2004 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 10889-3:2004(F)

Porte-outil à queue cylindrique —
Partie 3:
Porte-outil radial de type B
1 Domaine d'application
L'ISO 10889 est applicable aux porte-outil à queue cylindrique pour machines-outils à outils non rotatifs, en
particulier les machines de tournage.
La présente partie de l'ISO 10889 spécifie les dimensions, la désignation et les conditions techniques de
livraison complémentaires des porte-outil radiaux de types B1 à B8, à queue cylindrique conforme à
l'ISO 10889-1. Pour les porte-outil radiaux non normalisés, tels que par exemple ceux représentés sur les
dessins, il est recommandé d'appliquer les spécifications correspondantes de la présente partie de
l'ISO 10889.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 2768-1, Tolérances générales — Partie 1: Tolérances pour dimensions linéaires et angulaires non
affectées de tolérances individuelles
ISO 2768-2, Tolérances générales — Partie 2: Tolérances géométriques pour éléments non affectés de
tolérances individuelles
ISO 10889-1, Porte-outil à queue cylindrique — Partie 1: Queue cylindrique, alésage de réception —
Conditions t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.