ISO 9928-2:2007/PRF Amd 1
(Amendment)Cranes — Crane driving manual — Part 2: Mobile crane operators — Amendment 1
Cranes — Crane driving manual — Part 2: Mobile crane operators — Amendment 1
Appareils de levage à charge suspendue — Manuel à l'usage des conducteurs — Partie 2: Opérateurs de grues mobiles — Amendement 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 9928-2
First edition
2007-07-15
AMENDMENT 1
Cranes — Crane driving manual —
Part 2:
Mobile crane operators
AMENDMENT 1
Appareils de levage à charge suspendue — Manuel à l’usage des
conducteurs —
Partie 2: Opérateurs de grues mobiles
AMENDEMENT 1
PROOF/ÉPREUVE
Reference number
ISO 9928-2:2007/Amd.1:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 9928-2:2007/Amd.1:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 9928-2:2007/Amd.1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some o
...
© ISO 2002 – All rights reserved
Reference number of working document: ISO/TC 96/SC 6 N 562
Date: 2013‐2‐22
Reference number of document: ISO/DAM 9928-2
Committee identification: ISO/TC 96/SC 6
Secretariat: ANSI
Document type: International standard
Document subtype: if applicable
Document stage: (20) Preparation
Document language: E
Cranes — Crane operating driving manual —
Part 2: Mobile crane operators
Amendment 1
Appareils de levage à charge suspendue — Manuel à l'usage des
conducteurs —Partie 2:Grues mobiles
Warning
This document is not an ISO International Standard. It is distributed for review and comment. It is subject to
change without notice and may not be referred to as an International Standard.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Basic template BASICEN3 2002‐06‐01
---------------------- Page: 1 ----------------------
ISO DAM 9928-2
Copyright notice
This ISO document is a working draft or committee draft and is copyright‐protected by ISO. While
the reproduction of working drafts or committee drafts in any form for use by participants in the
ISO standards development process is permitted without prior permission from ISO, neither this
document nor any extract from it may be reproduced, stored or transmitted in any form for any
other purpose without prior written permission from ISO.
Requests for permission to reproduce this document for the purpose of selling it should be
addressed as shown below or to ISO’s member body in the country of the requester:
[Indicate :
the full address
telephone number
fax number
telex number
and electronic mail address
as appropriate, of the Copyright Manager of the ISO member body responsible for the secretariat of
the TC or SC within the framework of which the draft has been prepared]
Reproduction for sales purposes may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
iv © ISO 2002 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DAM 9928-2
Contents Page
Foreword iv
© ISO 2002 – All rights reserved v
---------------------- Page: 3 ----------------------
ISO DAM 9928-2
vi © ISO 2002 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/DAM 9928-2
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national
standards bodies (ISO member bodies). The work of preparing International Standards is normally
carried out through ISO technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on that committee.
International organizations, governmental and non‐governmental, in liaison with ISO, also take part in
the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all
mat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.