ISO/IEC 23008-4:2020
(Main)Information technology — High efficiency coding and media delivery in heterogeneous environments — Part 4: MMT reference software
Information technology — High efficiency coding and media delivery in heterogeneous environments — Part 4: MMT reference software
This document provides the reference software for MMT and its description.
Technologies de l'information — Codage à haute efficacité et livraison des medias dans des environnements hétérogènes — Partie 4: Logiciel de référence pour le transport des médias MPEG (MMT)
General Information
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 23008-4
First edition
2020-06
Information technology — High
efficiency coding and media delivery
in heterogeneous environments —
Part 4:
MMT reference software
Technologies de l'information — Codage à haute efficacité et livraison
des medias dans des environnements hétérogènes —
Partie 4: Logiciel de référence pour le transport des médias MPEG
(MMT)
Reference number
ISO/IEC 23008-4:2020(E)
©
ISO/IEC 2020
---------------------- Page: 1 ----------------------
ISO/IEC 23008-4:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO/IEC 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 23008-4:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 1
5 Configuration file format . 6
6 Version control and compiling . 7
7 Execution . 7
© ISO/IEC 2020 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 23008-4:2020(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that
are members of ISO or IEC participate in the development of International Standards through
technical committees established by the respective organization to deal with particular fields of
technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other
international organizations, governmental and non-governmental, in liaison with ISO and IEC, also
take part in the work.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents) or the IEC
list of patent declarations received (see http:// patents .iec .ch).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 29, Coding of audio, picture, multimedia and hypermedia information.
A list of all parts in the ISO/IEC 23008 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO/IEC 2020 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC 23008-4:2020(E)
Introduction
The MMT reference and conformance software is defined as part of the MPEG-H standard in this
document. This document outlines the MMT reference and conformance software and describes how it
is used for conformance testing. It also collects a list of MMT features that need to be verified as part of
conformance testing.
The attachment, available at https:// standards .iso .org/ iso -iec/ 23008/ -4/ ed -1/ en, contains the updated
reference software source code implementing the MPEG media transport: MMT.tar.gz.
© ISO/IEC 2020 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO/IEC 23008-4:2020(E)
Information technology — High efficiency coding and
media delivery in heterogeneous environments —
Part 4:
MMT reference software
1 Scope
This document provides the reference software for MMT and its description.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/IEC 23008-1, Information technology — High efficiency coding and media delivery in heterogeneous
environments — Part 1: MPEG media transport (MMT)
3 Terms and definitions
For the purposes of this document, the following terms and definitions given in ISO/IEC 23008-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
4 General
The reference and conformance software operates according to Figure 1. It takes as input the MPUs,
generic files and signalling messages that are to be transmitted. The MMTP sender then generates the
MMTP flow as a multiplex of MMTP packets from the different sources and uses BSD sockets to send
them to a pre-configured destination IP address and port number using MMTP over UDP. The MMTP
receiver de-multiplexes the MMTP flow based on the packet_id and the mode and passes the packets
to the corresponding reconstruction module. The reconstruction module extracts the payload and
reconstructs the resource (i.e. the MPU, the generic file, or the signalling message).
© ISO/IEC 2020 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO/IEC 23008-4:2020(E)
Figure 1 — Operation of reference and conformance software
Figures 2 and 3 depict the structure and class diagram of the reference and conformance software. The
yellow, orange and green boxes indicate classes, general or binary files (MPU, generic, configuration,
and packet dump), and XML files respectively.
Figure 2 — Class diagram of MMTP sender
2 © ISO/IEC 2020 – All rights reserved
---------------------- Page: 7 -------------------
...
DRAFT INTERNATIONAL STANDARD
ISO/IEC DIS 23008-4
ISO/IEC JTC 1/SC 29 Secretariat: JISC
Voting begins on: Voting terminates on:
2015-09-21 2015-12-21
Information technology — High efficiency coding and
media delivery in heterogeneous environments —
Part 4:
MMT Reference and Conformance Software
Technologies de l’information — Codage à haute efficacité et livraison des medias dans des
environnements hétérogènes
ICS: 35.040
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/IEC DIS 23008-4:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO/IEC 2015
---------------------- Page: 1 ----------------------
ISO/IEC DIS 23008-4:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO/IEC 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC DIS 23008-4
Contents
1 Scope . 7
2 References . 7
3 Terms, Definitions and Abbreviated Terms . 7
4 Software Architecture . 8
5 Configuration File Format . 12
6 Version Control and Compiling . 13
© ISO/IEC 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC DIS 23008-4
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 23008-4 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 29, Coding of audio, picture, multimedia and hypermedia information.
This second/third/. edition cancels and replaces the first/second/. edition (), [clause(s) / subclause(s) /
table(s) / figure(s) / annex(es)] of which [has / have] been technically revised.
ISO/IEC 23008 consists of the following parts, under the general title Information technology — High efficiency
coding and media delivery in heterogeneous environments:
⎯ Part 1: MPEG media transport (MMT)
- Part 2: High efficiency video coding (HEVC)
- Part 4: MMT Reference Software
- Part 7: Conformance for MPEG Media Transport
- Part 10: FEC Codes
- Part 11: Composition Information (CI)
- Part 13: MPEG media transport (MMT) Implementation Guideline
© ISO/IEC 2015 – All rights reserved iv
---------------------- Page: 4 ----------------------
ISO/IEC DIS 23008-4
Introduction
This part of ISO/IEC 23008 specifies the reference software. The reference software of ISO/IEC 23009 serves
two main purposes:
⎯ Validation of the written specification of the several parts of ISO/IEC 23008;
⎯ Clarification of the written specification of the several parts of ISO/IEC 23008
© ISO/IEC 2015 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO/IEC DIS 23008-4
Information technology — High efficiency coding and media delivery
in heterogeneous environments — Part 4: MMT Reference and
Conformance Software
1 Scope
This part of ISO/IEC 23008 specifies the reference software implementing the normative clauses of some
parts of ISO/IEC 23008.
That is, test vectors comprising MMTP sender and MMTP Receiver that conform or do not conform to the
normative clauses of the other parts of ISO/IEC 23008 and corresponding software modules.
2 References
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) shall apply.
ISO/IEC 23008-1 Information technology — Part 1: MPEG Media Transport
ISO/IEC 23008-10 In
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.