ISO 19699-2:2017

Superabsorbent polymer — Sodium polyacrylate resin for absorbing blood — Part 2: Specifications

ISO 19699-2:2017 specifies the requirements for properties, marking and packaging of superabsorbent polymer (SAP) made from sodium polyacrylate resin for absorbing blood. ISO 19699-2:2017 applies to sodium polyacrylate resin, as raw material, and applies to SAP for the final products used for absorbing blood.

Résines super-absorbantes — Polyacrylate de sodium pour l'absorption du sang — Partie 2: Spécifications

General Information

• Status: Published
• Publication Date: 13-Aug-2017
• ICS: 83.140.99 - Other rubber and plastics products
• Technical Committee: ISO/TC 61/SC 11 - Products
• Drafting Committee: ISO/TC 61/SC 11 - Products
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 29-Jul-2022

Relations

• Consolidated By: ISO 22635:2019 - Adhesives — Test methods for adhesives for plastic or rubber floor coverings or wall coverings — Determination of dimensional changes after accelerated ageing
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 19699-2
First edition
2017-08
Superabsorbent polymer — Sodium
polyacrylate resin for absorbing
blood —
Part 2:
Specifications
Résines super-absorbantes — Polyacrylate de sodium pour
l’absorption du sang —
Partie 2: Spécifications
Reference number
ISO 19699-2:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 19699-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 19699-2:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 1
3.1 Terms and definitions . 1
3.2 Abbreviated terms . 2
4 Requirements . 2
5 Marking (optional) . 2
6 Packaging . 2
6.1 Appearance . 2
6.2 Performance characteristics. 3
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 19699-2:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
A list of all parts in the ISO 19699 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 19699-2:2017(E)

Int
...