Carbon-fibre-reinforced plastics — Determination of the size and aspect ratio of crushed objects — Amendment 1

Plastiques renforcés de fibres de carbone — Détermination des dimensions et du rapport d'apparence d'objets broyés — Amendement 1

General Information

Status
Published
Publication Date
08-May-2018
Current Stage
6060 - International Standard published
Start Date
09-May-2018
Completion Date
09-May-2018
Ref Project

RELATIONS

Buy Standard

Standard
ISO 30012:2016/Amd 1:2018
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 30012
First edition
2016-02-01
AMENDMENT 1
2018-04
Carbon-fibre-reinforced plastics —
Determination of the size and aspect
ratio of crushed objects
AMENDMENT 1
Plastiques renforcés de fibres de carbone — Détermination des
dimensions et du rapport d'apparence d'objets broyés
AMENDEMENT 1
Reference number
ISO 30012:2016/Amd.1:2018(E)
ISO 2018
---------------------- Page: 1 ----------------------
ISO 30012:2016/Amd.1:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 30012:2016/Amd.1:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/iso/foreword .html.

This document was prepared by Technical committee ISO/TC 61, Plastics, Subcommittee SC 13,

Composites and reinforcement fibres.
© ISO 2018 – All rights reserved iii
---------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.