Sampling procedures for inspection by attributes — Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection — Technical Corrigendum 1

Règles d'échantillonnage pour les contrôles par attributs — Partie 1: Plans d'échantillonnage pour les contrôles lot par lot, indexés d'après le niveau de qualité acceptable (NQA) — Rectificatif technique 1

Sampling procedures for inspection by attributes - Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection - Technical corrigendum 1

General Information

Status

Withdrawn

Publication Date

21-Jul-1993

Withdrawal Date

21-Jul-1993

ICS

03.120.30 - Application of statistical methods

Technical Committee

ISO/TC 69/SC 5 - Acceptance sampling

Drafting Committee

ISO/TC 69/SC 5/WG 2 - Sampling procedures for inspection by attributes (Revision of ISO 2859)

Current Stage

9599 - Withdrawal of International Standard

Completion Date

18-Nov-1999

Ref Project

SIST ISO 2859-1:1996/C1:1996 - ISO 2859-1:1989/Cor 1:1993

Relations

Revised

ISO 2859-1:1999 - Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection

Effective Date

15-Apr-2008

Revised

SIST ISO 2859-1:2003 - Sampling procedures for inspection by attributes -- Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection

Effective Date

12-May-2008

Corrects

ISO 2859-1:1989 - Sampling procedures for inspection by attributes — Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection

Effective Date

06-Jun-2022

Child

ISO 2859-1:1989 - Sampling procedures for inspection by attributes — Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection

Effective Date

15-Apr-2008

Child

SIST ISO 2859-1:1996 - Sampling procedures for inspection by attributes -- Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection

Effective Date

12-May-2008

Consolidated By

ISO 14630:2005 - Non-active surgical implants — General requirements

Effective Date

06-Jun-2022

Buy Standard

Standard

ISO 2859-1:1989/Cor 1:1993

English language

2 pages

sale 15% off

Preview

sale 15% off

Preview

Standard

ISO 2859-1:1989/Cor 1:1993

French language

2 pages

sale 15% off

Preview

sale 15% off

Preview

Corrigendum

ISO 2859-1:1996/C1:1996

English language

2 pages

sale 10% off

Preview

sale 10% off

Preview

e-Library read for

1 day

Standards Content (Sample)

INTERNATIONAL STANDARD IS0 285901:1989
TECHNICAL CORRIGENDUM 1
Published 1993-07-15
lNTEMAnoNu onGANKAnoN FOR STANDARDuAnoN.MU)(13YHA~~HAFI oPrAHu3Alpw no cTAHC\APTH3ALpwl. oRGANlsAnoN NmwmoNALE M mwAL8sAm
Sampling procedures for inspection by attributes -
Part 1:
Sampling plans indexed by acceptable quality level (AQL)
for lot-by-lot inspection
TECHNICAL CORRIGENDUM 1
R&g/es d%chanti/lonnage pour /es contrhles par attributs -
Partie 1: Plans d’khantiiionnage pour ies contr6ies lot par lot, index& d’apr&s ie niveau de qua/it6 acceptable (NQA)
RECTIFiCATiF 7ECHNiQUE 1
Technical corrigendum 1 to International Standard IS0 2859~1:1989 was prepared by Technical Committee ISO/rC 69,
Applicati
...

NORME INTERNATIONALE IS0 2859-1 ~1989
RECTIFICATIF TECHNIQUE 1
Publié 1993-07- 15
Règles d'échantillonnage pour les contrôles par attributs -
Partie 1:
Plans d'échantillonnage pour les contrôles lot par lot,
indexés d'après le niveau de qualité acceptable (NQA)
RECTIFICATIF TECHNIQUE iq
Sampling procedures for inspection by attributes -
Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection
TECHNICAL CORRIGENDUM 1
Le Rectificatif technique 1 à la Norme internationale IS0 2859-1:1989 a été préparé par le comité technique lSO/rC 69,
Application des méthodes statistiques, sous-comité SC 5, Échantillonnage en vue d'acceptation.
Page 48
Le graphique H doit être remplacé par le graph
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sampling procedures for inspection by attributes - Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection - Technical corrigendum 1ISO 2859-1:1989/Cor 1:199303.120.30Application of statistical methodsICS:Ta slovenski standard je istoveten z:ISO 2859-1:1989/Cor 1:1993SIST ISO 2859-1:1996/C1:1996en01-september-1996SIST ISO 2859-1:1996/C1:1996SLOVENSKI
STANDARD

SIST ISO 2859-1:1996/C1:1996

INTERNATIONAL STANDARD IS0 285901:1989 TECHNICAL CORRIGENDUM 1 Published 1993-07-15 lNTEMAnoNu onGANKAnoN FOR STANDARDuAnoN.MU)(13YHA~~HAFI oPrAHu3Alpw no cTAHC\APTH3ALpwl. oRGANlsAnoN NmwmoNALE M mwAL8sAm Sampling procedures for inspection by attributes - Part 1: Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection TECHNICAL CORRIGENDUM 1 R&g/es d%chanti/lon
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO

ISO 28596:2022(Main)

Sampling procedures for inspection by attributes — Two-stage sampling plans for auditing and for inspection under prior information

This document specifies two-stage (double) sampling plans by attributes for inspection for a proportion of nonconforming items in a target population of discrete units, in particular: a) the proportion of nonconforming items in a lot of product items; b) the proportion of nonconforming function instances of an internal control system (ICS); c) the proportion of misstatements in a population of accounting entries or booking records; d) the proportion of nonconforming test characteristics of an entity subject to an acceptance test, e.g. in product and process audits. The plans are preferable to single sampling plans where the cost of inspection is high or where the delay and uncertainty caused by the possible requirement for second samples is inconsequential. The statistical theory underlying the plans, tables and figures are provided in Annexes A through K.

Standard
41 pages
English language
sale 15% off

ISO

ISO 3951-1:2022(Main)

Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL

SIST ISO 3951-1:2023

This document specifies single sampling plans for lot-by-lot inspection under the following conditions: a) where the inspection procedure is applied to a continuing series of lots of discrete products, all supplied by one producer using one production process; b) where only a single quality characteristic, x, of these products is taken into consideration, which is measurable on a continuous scale; c) where production is under statistical control and the quality characteristic, x, is distributed according to a normal distribution or a close approximation to the normal distribution; d) where a contract or standard defines a lower specification limit, L, an upper specification limit, U, or both. An item is qualified as conforming if its measured quality characteristic, x, satisfies as appropriate one of the following inequalities: 1) x ≥ L (i.e. the lower specification limit is not violated); 2) x ≤ U (i.e. the upper specification limit is not violated); 3) x ≥ L and x ≤ U (i.e. neither the lower nor the upper specification limit is violated). Inequalities 1) and 2) are cases with a single specification limit, and 3) is a case with double specification limits. Where double specification limits apply, it is assumed in this document that conformity to both specification limits is equally important to the integrity of the product. In such cases, it is appropriate to apply a single AQL to the combined percentage of a product outside the two specification limits. This is referred to as combined control.

Standard
114 pages
English language
sale 10% off
e-Library read for
1 day
Standard
107 pages
English language
sale 15% off
Standard
110 pages
French language
sale 15% off

ISO

ISO 2859-4:2020(Main)

Sampling procedures for inspection by attributes — Part 4: Procedures for assessment of declared quality levels

SIST ISO 2859-4:2021

This document establishes single sampling plans for conformance testing, i.e., for assessing whether the quality level of a relevant audit population (lot, process, inventory, file etc) conforms to a declared value. Sampling plans are provided corresponding to four levels of discriminatory ability. The limiting quality ratio (LQR) (see Clause 4) of each sampling plan is given for reference. For levels I-III, the sampling plans have been devised so as to obtain a risk no more than 5 % of contradicting a correct declared quality level. The risk of failing to contradict an incorrectly declared quality level which is related to the LQR is no more than 10 %. The sample sizes for level 0 are designed in a way that the LQR factors of the sampling plans are compatible with the LQR factors for level I. In contrast to the procedures in the other parts of the ISO 2859 series, the procedures in this document are not applicable to acceptance assessment of lots. Generally, this document mainly focuses on controlling type I error, which differs from the balancing of the risks in the procedures for acceptance sampling. This document can be used for various forms of quality inspection in situations where objective evidence of conformity to some declared quality level is to be provided by means of inspection of a sample. The procedures are applicable to entities such as lots, process output, etc. that allow random samples of individual items to be taken from the entity. The sampling plans provided in this document are applicable, but not limited, to the inspection of a variety of targets such as: — end items; — components and raw materials; — operations; — materials in process; — supplies in storage; — maintenance operations; — data or records; — administrative procedures; — accounting procedures or accounting entries; — internal control procedures. This document considers two types of quality models for discrete items and populations, as follows. i) The conforming-nonconforming model, where each item is classified as conforming or nonconforming, and where the quality indicator of a population of items is the proportion p of nonconforming items, or, equivalently, the percentage 100 p of nonconforming items. ii) The nonconformities model, where the number of nonconformities is counted on each item, and where the quality indicator of a population of items is the average number λ of nonconformities found on items in the population, or, equivalently, the percentage 100 λ of nonconformities on items in the population.

Standard
23 pages
English language
sale 10% off
e-Library read for
1 day
Standard
18 pages
English language
sale 15% off
Standard
19 pages
French language
sale 15% off
Draft
18 pages
English language
sale 15% off

ISO

ISO 2859-2:2020(Main)

Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection

SIST ISO 2859-2:2020

This document specifies an acceptance sampling system for inspection by attributes indexed by limiting quality (LQ). The sampling system is used for lots in isolation (isolated sequences of lots, an isolated lot, a unique lot or a short series of lots), where switching rules, such as those of ISO 2859‑1, are not applicable. Inspection levels, as provided by ISO 2859‑1 to control the relative amount of inspection, are not provided in this document. In many industrial situations, in which switching rules might be used, they are not applied for a number of reasons, not all of which might be valid: a) production is intermittent (not continuous); b) production is from several different sources in varying quantities, i.e. "job lots"; c) lots are isolated; d) lots are resubmitted after inspection. The sampling plans in this document are indexed by a series of specified values of limiting quality (LQ), where the consumer's risk (the probability of acceptance at the LQ) is usually below 0,10 (10 %), except in some instances. This document is intended both for inspection for nonconforming items and for inspection for nonconformities per 100 items. It is intended to be used when the supplier and the consumer both regard the lot to be in isolation. That is, the lot is unique in that it is the only one of its type produced. It can also be used when there is a series of lots too short for switching rules to be applied.

Standard
50 pages
English language
sale 10% off
e-Library read for
1 day
Standard
46 pages
English language
sale 15% off
Standard
46 pages
French language
sale 15% off

ISO

ISO 39511:2018(Main)

Sequential sampling plans for inspection by variables for percent nonconforming (known standard deviation)

SIST ISO 39511:2018

This International Standard specifies sequential sampling plans and procedures for inspection by variables of discrete items. The plans are indexed in terms of producer's risk point and the consumer's risk point. Therefore, they are suitable not only for the purposes of acceptance sampling, but for the more general purpose of the testing of simple statistical hypotheses for proportions. The purpose of this International Standard is to provide procedures for the sequential assessment of inspection results that may be used to induce the supplier to supply lots of a quality having a high probability of acceptance. At the same time, the consumer is protected by a prescribed upper limit to the probability of accepting a lot (or process) of poor quality. This International Standard is primarily designed for use under the following conditions: a) where the inspection procedure is to be applied to a continuing series of lots of discrete products all supplied by one producer using one production process. In such a case, sampling of particular lots is equivalent to the sampling of the process. If there are different producers or production processes, this International Standard shall be applied to each one separately; b) where only a single quality characteristic x of these products is taken into consideration, which must be measurable on a continuous scale; c) where the measurement error is negligible (i.e. with a standard deviation no more than 10 % of the process standard deviation); d) where production is stable (under statistical control) and the quality characteristic x has a known standard deviation, and is distributed according to a normal distribution or a close approximation to the normal distribution; CAUTION — The procedures in this International Standard are not suitable for application to lots that have been screened previously for nonconforming items. e) where a contract or standard defines an upper specification limit U, a lower specification limit L, or both; an item is qualified as conforming if and only if its measured quality characteristic, x, satisfies the appropriate one of the following inequalities: x ≤ U (i.e. the upper specification limit is not violated); x ≥ L (i.e. the lower specification limit is not violated); and (i.e. neither the upper nor the lower specification limit is violated.) Inequalities 1) and 2) are called cases with a "single specification limit", and 3) is the case with "double specification limits". In this International Standard, it is assumed that, where double specification limits apply, conformance to both specification limits is either equally important to the integrity of the product or is considered separately for both specification limits. In the first case, it is appropriate to control the combined percentage of product outside the two specification limits. This is referred to as combined control. In the second case, nonconformity beyond each of the limits is controlled separately, and this is referred to as separate control.

Standard
35 pages
English language
sale 15% off
Standard
41 pages
English language
sale 10% off
e-Library read for
1 day
Standard
35 pages
French language
sale 15% off

ISO

ISO 28597:2017(Main)

Acceptance sampling procedures by attributes — Specified quality levels in nonconforming items per million

SIST ISO 28597:2018

ISO 28597:2017 specifies, for quality levels expressed as nonconforming items per million items, procedures for estimating the quality level of a single entity (e.g. a lot) and, when the production process is in statistical control, for estimating the process quality level based on evidence from several samples. Procedures are also specified for using this information when selecting a suitable sampling plan so as to verify that the quality level of a given lot does not exceed a stated limiting quality level (LQL). For the case where no prior sample data is available, guidance is given for presuming a process quality level in selecting a plan.

Standard
19 pages
English language
sale 15% off
Standard
25 pages
English language
sale 10% off
e-Library read for
1 day
Standard
19 pages
French language
sale 15% off

ISO

ISO 28593:2017(Main)

Acceptance sampling procedures by attributes — Accept-zero sampling system based on credit principle for controlling outgoing quality

ISO 28593:2017 specifies a system of single sampling schemes for lot-by-lot inspection by attributes. All the sampling plans of the present system are of accept-zero form, i.e. no lot is accepted if the sample from it contains one or more nonconforming items. The schemes depend on a suitably-defined average outgoing quality limit (AOQL), the value of which is chosen by the user; no restrictions are placed on the choice of the value of the AOQL or on the sizes of successive lots in the series. The methodology ensures that the overall average quality reaching the customer or market-place will not exceed the AOQL in the long run.

Standard
9 pages
English language
sale 15% off

ISO

ISO 28592:2017(Main)

Double sampling plans by attributes with minimal sample sizes, indexed by producer's risk quality (PRQ) and consumer's risk quality (CRQ)

SIST ISO 28592:2018

ISO 28592:2017 provides double sampling plans by attributes for the acceptance inspection of lots of discrete items. The plans are indexed by the producer's risk quality (PRQ) and the consumer's risk quality (CRQ) where the nominal producer's and consumer's risks are respectively either (5 %, 5 %), (5 %, 10 %) or (10 %, 10 %). Plans are provided for inspection for percent nonconforming and for inspection for nonconformities per 100 items. The lot is accepted if there are no nonconforming items (nonconformities) in the first random sample, and rejected if it contains two or more nonconforming items (nonconformities). If precisely one nonconforming item is found in the first sample, a second random sample is drawn; the lot is then accepted if the second sample contains no nonconforming items (nonconformities) and rejected otherwise. The objective of this International Standard is to provide procedures that enable lot disposition to be determined quickly and economically if quality is particularly good or bad. For intermediate quality, a second sample is drawn in order to be able to discriminate more reliably between acceptable and unacceptable lots. The two sample sizes are chosen to minimize the maximum expected sample size with respect to incoming quality subject to the nominal risks not being exceeded. Similarly, the plans may be used to test the hypothesis that a lot or process quality level is equal to the PRQ (i.e. acceptable) against the alternative hypothesis that the quality level is equal to the CRQ (i.e. unacceptable). The plans are preferable to single sampling plans where the cost of inspection is high, where the delay and uncertainty caused by the possible requirement for second samples is inconsequential and where a relatively large ratio of the consumer's risk quality to the producer's risk quality can be tolerated. The plans are suitable for isolated lots or for short series of lots, where the sum of the two sample sizes is no larger than about 10 % of the size of the lot. The plans are also suitable for continuing series of lots when lots that fail to satisfy the acceptance criteria are 100 % inspected and all nonconforming items replaced by conforming items; however, for continuing series of lots, consideration should also be given to using double sampling plans from ISO 2859‑1. The statistical theory underlying the plans, tables and figures is provided in Annex A.

Standard
79 pages
English language
sale 15% off
Standard
85 pages
English language
sale 10% off
e-Library read for
1 day

ISO

ISO 28590:2017(Main)

Sampling procedures for inspection by attributes — Introduction to the ISO 2859 series of standards for sampling for inspection by attributes

SIST ISO 28590:2018

ISO 28590:2017 provides a general introduction to acceptance sampling by attributes and provides a brief summary of the attribute sampling schemes and plans used in ISO 2859‑1, ISO 2859‑2, ISO 2859‑3, ISO 2859‑4 and ISO 2859‑5, which describe specific types of attribute sampling systems. It also provides guidance on the selection of the appropriate inspection system for use in a particular situation.

Standard
11 pages
English language
sale 15% off
Standard
17 pages
English language
sale 10% off
e-Library read for
1 day
Standard
11 pages
French language
sale 15% off

ISO

ISO 28598-1:2017(Main)

Acceptance sampling procedures based on the allocation of priorities principle (APP) — Part 1: Guidelines for the APP approach

ISO 28598-1:2017 provides guidelines specifying the organizational principles of acceptance sampling in situations where the contract or the legislation provides for successive inspection to be carried out by different parties: the supplier, the customer and/or a third party. These guidelines are designed for inspection of populations of any product supplied or delivered in discrete items in lots. They are applicable to - supplier inspection (final inspection, product certification upon supplier's request), - customer inspection (incoming inspection, audit inspection, acceptance sampling), - third-party inspection (certification of product, inspection and supervision for observance of International Standard requirements, quality inspection carried out at the supplier, and/or customer, request), where the quality levels and the lot acceptability criteria are specified unilaterally by the supplier or contractually by the supplier and the customer. These guidelines are also applicable to situations when only one sampling inspection is actually needed. NOTE Single sampling APP plans by attributes are given in ISO 28598‑2. The guidelines provided by this part of ISO 28598 may be applied in developing standards on acceptance sampling for standard inspection models, specific items or quality levels, as well as in developing contracts, specifications and instructions. In contractual use of the APP, the parties concerned should acknowledge in the contract that they approve of its principles (also by referring to the present guidelines). The parties may also provide for the use of the APP in disputes and arbitration.

Standard
26 pages
English language
sale 15% off
Standard
26 pages
French language
sale 15% off