ISO/IEC 29341-30-2:2017

Information technology — UPnP Device Architecture — Part 30-2: IoT management and control device control protocol — IoT management and control device

ISO/IEC 29341-30-2:2017 defines the device for IOT Management and Control, which identifies Level 1 of the device named IOT Management and Control. This Publicly Available Specification is applicable to Standardized DCPs of the UPnP Forum which include this device. This device definition is compliant with the UPnP Device Architecture version 1.0 [1]. It defines a device type referred to herein as IOT Management and Control device. This specification defines a general-purpose device that can be used to instantiate a bridge or gateway device that is connected to Sensors and Actuators. This device implements a bridge between the UPnP network and Sensors/Actuators endpoints. It exposes services to check the status, and send and receive data from Sensors. Sensors/Actuators may be connected using a variety of transport protocols including Bluetooth, ZigBee and IEEE 11073.

Technologies de l'information — Architecture de dispositif UPnP — Partie 30-2: Protocole de contrôle de dispositif de gestion et de contrôle de l'Internet des objets — Dispositif de gestion et de contrôle de l'Internet des objets

General Information

• Status: Published
• Publication Date: 01-Jun-2017
• ICS: 35.200 - Interface and interconnection equipment
• Technical Committee: ISO/IEC JTC 1 - Information technology
• Drafting Committee: ISO/IEC JTC 1 - Information technology
• Current Stage: 9060 - Close of review
• Start Date: 02-Dec-2027

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 29341-30-2
First edition
2017-06
Information technology — UPnP
Device Architecture —
Part 30-2:
IoT management and control device
control protocol — IoT management
and control device
Technologies de l’information — Architecture de dispositif UPnP —
Partie 30-2: Protocole de contrôle de dispositif de gestion et de
contrôle de l’Internet des objets — Dispositif de gestion et de contrôle
de l’Internet des objets
Reference number
ISO/IEC 29341-30-2:2017(E)
©
ISO/IEC 2017

---------------------- Page: 1 ----------------------
ISO/IEC 29341-30-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO/IEC 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 29341-30-2:2017(E)

CONTENTS

1  Scope . 1
2  Normative References . 1
3  Terms, Definitions and Abbreviations . 2
4  Notations and conventions . 2
4.1  Notation . 2
4.2  Data Types . 2
4.3  Vendor-defined Extensions . 3
5  Device Definitions . 3
5.1  Device Type . 3
5.2  Device Model . 3
5.2.1  Description of Device Requirements . 4
5.2.2  Relationships Between Services . 4
6  XML Device Description . 4
Annex A - Theory of Operation (informative) . 6
A.1  Introduction . 6
A.2  Device Discovery . 6
A.3  Sensor Discovery, Configuration and Status Reading . 6
A.4  Reading and Writing of Data . 6
A.5  Connecting Sensors to Transport Clients . 7
Figure 1 — IOT Management and Control Device Functional Diagram . 1
Figure A.1 —Simple Read and Write Flow Diagram. . 7
Figure A.2 — Connecting a IoT Management and Control Device to an External
Storage. . 8
Table 1 — Device Requirements . 3


 ISO/IEC 2017 – All rights reserved  iii

---------------------- Page: 3 ----------------------
ISO/IEC 29341-30-2:2017(E)

Foreword

ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical activity.
ISO and IEC technical committees collaborate in fields of mutual interest. Other international
organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
work. In the field of information technology, ISO and IEC have established a joint technical committee,
ISO/IEC JTC 1.

The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see http://www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.

For an explanation on the voluntary nature of Standards, the meaning of the ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword –
Supplementary information .

ISO/IEC 29341-30-2 was prepared by UPnP Forum and adopted, under the PAS procedure, by joint
technical committee ISO/IEC JTC 1, Information technology, in parallel with its approval by national
bodies of ISO and IEC.
The list of all currently available parts of ISO/IEC 29341 series, under the general title
Information technology — UPnP Device Architecture, can be found on the ISO web site.
iv   ISO/IEC 2017 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 29341-30-2:2017(E)

Introduction
ISO and IEC draw attention to the fact that it is claimed that compliance with this document may
involve the use of patents as indicated below.

ISO and IEC take no position concerning the evidence, validity and scope of these patent rights. The
holders of -these patent rights have assured ISO and IEC that they are willing to negotiate licenses
under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In
this respect, the statements of the holders of these patent rights are registered with ISO and IEC.

Intel Corporation has informed IEC and ISO that it has patent applications or granted patents.
Information may be obtained from:
Intel Corporation
Standards Licensing Department
5200 NE Elam Young Parkway
MS: JFS-98
USA – Hillsboro, Oregon 97124
Microsoft Corporation has informed IEC and ISO that it has patent applications or granted
patents as listed below:
6101499 / US; 6687755 / US; 6910068 / US; 7130895 / US; 6725281 / US; 7089307 / US;
7069312 / US; 10/783 524 /US
Information may be obtained from:
Microsoft Corporation
One Microsoft Way
USA – Redmond WA 98052
Philips International B.V. has informed IEC and ISO that it has patent applications or granted
patents.
Information may be obtained from:
Philips International B.V. – IP&S
High Tech campus, building 44 3A21
NL – 5656 Eindhoven
NXP B.V. (NL) has informed IEC and ISO that it has patent applications or granted patents.
Information may be obtained from:
NXP B.V. (NL)
High Tech campus 60
NL – 5656 AG Eindhoven
Matsushita Electric Industrial Co. Ltd. has informed IEC and ISO that it has patent
applications or granted patents.
Information may be obtained from:
Matsushita Electric Industrial Co. Ltd.
1-3-7 Shiromi, Chuoh-ku
JP – Osaka 540-6139
Hewlett Packard Company has informed IEC and ISO that it has patent applications or
granted patents as listed below:
5 956 487 / US; 6 170 007 / US; 6 139 177 / US; 6 529 936 / US; 6 470 339 / US; 6 571 388 /
US; 6 205 466 / US
 ISO/IEC 2017 – All rights reserved v

---------------------- Page: 5 ----------------------
ISO/IEC 29341-30-2:2017(E)

Information may be obtained from:
Hewlett Packard Company
1501 Page Mill Road
USA – Palo Alto, CA 94304
Samsung Electronics Co. Ltd. has informed IEC and ISO that it has patent applications or
granted patents.
Information may be obtained from:
Digital Media Business, Samsung Electronics Co. Ltd.
416 Maetan-3 Dong, Yeongtang-Gu,
KR – Suwon City 443-742
Huawei Technologies Co., Ltd. has informed IEC and ISO that it has patent applications or
granted patents.
Information may be obtained from:
Huawei Technologies Co., Ltd.
Administration Building, Bantian Longgang District
Shenzhen – China 518129
Qualcomm Incorporated has informed IEC and ISO that it has patent applications or granted
patents.
Information may be obtained from:
Qualcomm Incorporated
5775 Morehouse Drive
San Diego, CA – USA 92121
Telecom Italia S.p.A.has informed IEC and ISO that it has patent applications or granted
patents.
Information may be obtained from:
Telecom Italia S.p.A.
Via Reiss Romoli, 274
Turin - Italy 10148
Cisco Systems informed IEC and ISO that it has patent applications or granted patents.
Information may be obtained from:
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA – USA 95134
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights other than those identified above. ISO and IEC shall not be held responsible for
identifying any or all such patent rights.

vi   ISO/IEC 2017 – All rights reserved

---------------------- Page: 6 ----------------------
ISO/IEC 29341-30-2:2017(E)

Original UPnP Document
Reference may be made in this document to original UPnP documents. These references are
retained in order to maintain consistency between the specifications as published by ISO/IEC
and by UPnP Implementers Corporation and later by UPnP Forum. The following table
indicates the original UPnP document titles and the corresponding part of ISO/IEC 29341:
UPnP Document Title ISO/IEC 29341 Part
UPnP Device Architecture 1.0 ISO/IEC 29341-1:2008
UPnP Device Architecture Version 1.0 ISO/IEC 29341-1:2011
UPnP Device Architecture 1.1 ISO/IEC 29341-1-1:2011
UPnP Device Architecture 2.0 ISO/IEC 29341-1-2
UPnP Basic:1 Device ISO/IEC 29341-2
UPnP AV Architecture:1 ISO/IEC 29341-3-1:2008
UPnP AV Architecture:1 ISO/IEC 29341-3-1:2011
UPnP AVTransport:1 Service ISO/IEC 29341-3-10
UPnP ConnectionManager:1 Service ISO/IEC 29341-3-11
UPnP ContentDirectory:1 Service ISO/IEC 29341-3-12
UPnP RenderingControl:1 Service ISO/IEC 29341-3-13
UPnP MediaRenderer:1 Device ISO/IEC 29341-3-2
UPnP MediaRenderer:2 Device ISO/IEC 29341-3-2:2011
UPnP MediaServer:1 Device ISO/IEC 29341-3-3
UPnP AVTransport:2 Service ISO/IEC 29341-4-10:2008
UPnP AVTransport:2 Service ISO/IEC 29341-4-10:2011
UPnP ConnectionManager:2 Service ISO/IEC 29341-4-11:2008
UPnP ConnectionManager:2 Service ISO/IEC 29341-4-11:2011
UPnP ContentDirectory:2 Service ISO/IEC 29341-4-12
UPnP RenderingControl:2 Service ISO/IEC 29341-4-13:2008
UPnP RenderingControl:2 Service ISO/IEC 29341-4-13:2011
UPnP ScheduledRecording:1 ISO/IEC 29341-4-14
UPnP ScheduledRecording:2 ISO/IEC 29341-4-14:2011
UPnP MediaRenderer:2 Device ISO/IEC 29341-4-2
UPnP MediaServer:2 Device ISO/IEC 29341-4-3
UPnP AV Datastructure Template:1 ISO/IEC 29341-4-4:2008
UPnP AV Datastructure Template:1 ISO/IEC 29341-4-4:2011
UPnP DigitalSecurityCamera:1 Device ISO/IEC 29341-5-1
UPnP DigitalSecurityCameraMotionImage:1 Service ISO/IEC 29341-5-10
UPnP DigitalSecurityCameraSettings:1 Service ISO/IEC 29341-5-11
UPnP DigitalSecurityCameraStillImage:1 Service ISO/IEC 29341-5-12
UPnP HVAC_System:1 Device ISO/IEC 29341-6-1
UPnP ControlValve:1 Service ISO/IEC 29341-6-10
UPnP HVAC_FanOperatingMode:1 Service ISO/IEC 29341-6-11
UPnP FanSpeed:1 Service ISO/IEC 29341-6-12
UPnP HouseStatus:1 Service ISO/IEC 29341-6-13
UPnP HVAC_SetpointSchedule:1 Service ISO/IEC 29341-6-14
UPnP TemperatureSensor:1 Service ISO/IEC 29341-6-15
UPnP TemperatureSetpoint:1 Service ISO/IEC 29341-6-16
UPnP HVAC_UserOperatingMode:1 Service ISO/IEC 29341-6-17
UPnP HVAC_ZoneThermostat:1 Device ISO/IEC 29341-6-2
 ISO/IEC 2017 – All rights reserved vii

---------------------- Page: 7 ----------------------
ISO/IEC 29341-30-2:2017(E)

UPnP BinaryLight:1 Device ISO/IEC 29341-7-1
UPnP Dimming:1 Service ISO/IEC 29341-7-10
UPnP SwitchPower:1 Service ISO/IEC 29341-7-11
UPnP DimmableLight:1 Device ISO/IEC 29341-7-2
UPnP InternetGatewayDevice:1 Device ISO/IEC 29341-8-1
UPnP LANHostConfigManagement:1 Service ISO/IEC 29341-8-10
UPnP Layer3Forwarding:1 Service ISO/IEC 29341-8-11
UPnP LinkAuthentication:1 Service ISO/IEC 29341-8-12
UPnP RadiusClient:1 Service ISO/IEC 29341-8-13
UPnP WANCableLinkConfig:1 Service ISO/IEC 29341-8-14
UPnP WANCommonInterfaceConfig:1 Service ISO/IEC 29341-8-15
UPnP WANDSLLinkConfig:1 Service ISO/IEC 29341-8-16
UPnP WANEthernetLinkConfig:1 Service ISO/IEC 29341-8-17
UPnP WANIPConnection:1 Service ISO/IEC 29341-8-18
UPnP WANPOTSLinkConfig:1 Service ISO/IEC 29341-8-19
UPnP LANDevice:1 Device ISO/IEC 29341-8-2
UPnP WANPPPConnection:1 Service ISO/IEC 29341-8-20
UPnP WLANConfiguration:1 Service ISO/IEC 29341-8-21
UPnP WANDevice:1 Device ISO/IEC 29341-8-3
UPnP WANConnectionDevice:1 Device ISO/IEC 29341-8-4
UPnP WLANAccessPointDevice:1 Device ISO/IEC 29341-8-5
UPnP Printer:1 Device ISO/IEC 29341-9-1
UPnP ExternalActivity:1 Service ISO/IEC 29341-9-10
UPnP Feeder:1.0 Service ISO/IEC 29341-9-11
UPnP PrintBasic:1 Service ISO/IEC 29341-9-12
UPnP Scan:1 Service ISO/IEC 29341-9-13
UPnP Scanner:1.0 Device ISO/IEC 29341-9-2
UPnP QoS Architecture:1.0 ISO/IEC 29341-10-1
UPnP QosDevice:1 Service ISO/IEC 29341-10-10
UPnP QosManager:1 Service ISO/IEC 29341-10-11
UPnP QosPolicyHolder:1 Service ISO/IEC 29341-10-12
UPnP QoS Architecture:2 ISO/IEC 29341-11-1
UPnP QosDevice:2 Service ISO/IEC 29341-11-10
UPnP QosManager:2 Service ISO/IEC 29341-11-11
UPnP QosPolicyHolder:2 Service ISO/IEC 29341-11-12
UPnP QOS v2 Schema Files ISO/IEC 29341-11-2
UPnP RemoteUIClientDevice:1 Device ISO/IEC 29341-12-1
UPnP RemoteUIClient:1 Service ISO/IEC 29341-12-10
UPnP RemoteUIServer:1 Service ISO/IEC 29341-12-11
UPnP RemoteUIServerDevice:1 Device ISO/IEC 29341-12-2
UPnP DeviceSecurity:1 Service ISO/IEC 29341-13-10
UPnP SecurityConsole:1 Service ISO/IEC 29341-13-11
UPnP ContentDirectory:3 Service ISO/IEC 29341-14-12:2011
UPnP MediaServer:3 Device ISO/IEC 29341-14-3:2011
UPnP ContentSync:1 ISO/IEC 29341-15-10:2011
UPnP Low Power Architecture:1 ISO/IEC 29341-16-1:2011
UPnP LowPowerProxy:1 Service ISO/IEC 29341-16-10:2011
viii   ISO/IEC 2017 – All rights reserved

---------------------- Page: 8 ----------------------
ISO/IEC 29341-30-2:2017(E)

UPnP LowPowerDevice:1 Service ISO/IEC 29341-16-11:2011
UPnP QoS Architecture:3 ISO/IEC 29341-17-1:2011
UPnP QosDevice:3 Service ISO/IEC 29341-17-10:2011
UPnP QosManager:3 Service ISO/IEC 29341-17-11:2011
UPnP QosPolicyHolder:3 Service ISO/IEC 29341-17-12:2011
UPnP QosDevice:3 Addendum ISO/IEC 29341-17-13:2011
UPnP RemoteAccessArchitecture:1 ISO/IEC 29341-18-1:2011
UPnP InboundConnectionConfig:1 Service ISO/IEC 29341-18-10:2011
UPnP RADAConfig:1 Service ISO/IEC 29341-18-11:2011
UPnP RADASync:1 Service ISO/IEC 29341-18-12:2011
UPnP RATAConfig:1 Service ISO/IEC 29341-18-13:2011
UPnP RAClient:1 Device ISO/IEC 29341-18-2:2011
UPnP RAServer:1 Device ISO/IEC 29341-18-3:2011
UPnP RADiscoveryAgent:1 Device ISO/IEC 29341-18-4:2011
UPnP SolarProtectionBlind:1 Device ISO/IEC 29341-19-1:2011
UPnP TwoWayMotionMotor:1 Service ISO/IEC 29341-19-10:2011
UPnP AV Architecture:2 ISO/IEC 29341-20-1
UPnP AVTransport:3 Service ISO/IEC 29341-20-10
UPnP ConnectionManager:3 Service ISO/IEC 29341-20-11
UPnP ContentDirectory:4 Device ISO/IEC 29341-20-12
UPnP RenderingControl:3 Service ISO/IEC 29341-20-13
UPnP ScheduledRecording:2 Service ISO/IEC 29341-20-14
UPnP MediaRenderer:3 Service ISO/IEC 29341-20-2
UPnP MediaServer:4 Device ISO/IEC 29341-20-3
UPnP AV Datastructure Template:1 ISO/IEC 29341-20-4
UPnP InternetGatewayDevice:2 Device ISO/IEC 29341-24-1
UPnP WANIPConnection:2 Service ISO/IEC 29341-24-10
UPnP WANIPv6FirewallControl:1 Service ISO/IEC 29341-24-11
UPnP WANConnectionDevice:2 Service ISO/IEC 29341-24-2
UPnP WANDevice:2 Device ISO/IEC 29341-24-3
UPnP Telephony Architecture:2 ISO/IEC 29341-26-1
UPnP CallManagement:2 Service ISO/IEC 29341-26-10
UPnP MediaManagement:2 Service ISO/IEC 29341-26-11
UPnP Messaging:2 Service ISO/IEC 29341-26-12
UPnP PhoneManagement:2 Service ISO/IEC 29341-26-13
UPnP AddressBook:1 Service ISO/IEC 29341-26-14
UPnP Calendar:1 Service ISO/IEC 29341-26-15
UPnP Presense:1 Service ISO/IEC 29341-26-16
UPnP TelephonyClient:2 Device ISO/IEC 29341-26-2
UPnP TelephonyServer:2 Device ISO/IEC 29341-26-3
UPnP Friendly Info Update:1 Service ISO/IEC 29341-27-1
UPnP MultiScreen MultiScreen Architecture:1
ISO/IEC 29341-28-1
UPnP MultiScreen Application Management:1 Service
ISO/IEC 29341-28-10
UPnP MultiScreen Screen:1 Device
ISO/IEC 29341-28-2
UPnP MultiScreen Application Management:2 Service
ISO/IEC 29341-29-10
UPnP MultiScreen Screen:2 Device
ISO/IEC 29341-29-2
UPnP IoT Management and Control Architecture Overview:1
ISO/IEC 29341-30-1
 ISO/IEC 2017 – All rights reserved ix

---------------------- Page: 9 ----------------------
ISO/IEC 29341-30-2:2017(E)

UPnP DataStore:1 Service
ISO/IEC 29341-30-10
UPnP IoT Management and Control Data Model:1 Service
ISO/IEC 29341-30-11
UPnP IoT Management and Control Transport Generic:1
Service ISO/IEC 29341-30-12
UPnP IoT Management and Control:1 Device
ISO/IEC 29341-30-2
UPnP Energy Management:1 Service ISO/IEC 29341-31-1


x   ISO/IEC 2017 – All rights reserved

---------------------- Page: 10 ----------------------
ISO/IEC 29341-30-2:2017(E)

1 Scope
This document defines the device for IOT Management and Control, which identifies Level 1
of the device named IOT Management and Control. This Publicly Available Specification is
applicable to Standardized DCPs of the UPnP Forum which include this device.
This device definition is complia
...