ISO 5892:2013
(Main)Rubber building gaskets — Materials for preformed solid vulcanized structural gaskets — Specification
Rubber building gaskets — Materials for preformed solid vulcanized structural gaskets — Specification
ISO 5892:2013 specifies material requirements for preformed, solid vulcanized rubber structural gaskets in sealing and supporting applications for buildings.
Profilés en caoutchouc pour le bâtiment — Matériaux pour profilés de structure compacts préformés vulcanisés — Spécifications
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 5892
Second edition
2013-06-15
Rubber building gaskets — Materials
for preformed solid vulcanized
structural gaskets — Specification
Profilés en caoutchouc pour le bâtiment — Matériaux pour profilés de
structure compacts préformés vulcanisés — Spécifications
Reference number
©
ISO 2013
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Types of material . 2
5 Working temperature range. 2
6 Material and workmanship . 2
7 Dimensions and tolerances . 2
8 General requirements . 2
8.1 Test pieces . 2
8.2 Hardness . 3
8.3 Tensile strength and elongation at break . 3
8.4 Compression set . . 3
8.5 Accelerated ageing . 3
8.6 Ozone resistance. 3
9 Specific requirements . 4
9.1 General . 4
9.2 High-density ozone resistance . 4
9.3 Holding force . 4
9.4 Watertightness . 4
9.5 Flammability . 4
9.6 Contact and migration staining . 4
9.7 Low-temperature brittleness . 4
9.8 Low-temperature compression set . 4
Annex A (informative) Holding force test . 6
Bibliography . 9
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 4, Products (other than hoses).
This second edition cancels and replaces the first edition (ISO 5892:1981), which has been technically revised.
iv © ISO 2013 – All rights reserved
INTERNATIONAL STANDARD ISO 5892:2013(E)
Rubber building gaskets — Materials for preformed solid
vulcanized structural gaskets — Specification
1 Scope
This International Standard specifies material requirements for preformed, solid vulcanized rubber
structural gaskets in sealing and supporting applications for buildings.
NOTE Specifications for non-supporting gaskets are given in ISO 3934.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 812:2011, Rubber, vulcanized or thermoplastic — Determination of low-temperature brittleness
ISO 815-1, Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient
or elevated temperatures
ISO 815-2, Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low
temperatures
ISO 1382, Rubber — Vocabulary
ISO 1431-1, Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and
dynamic strain testing
ISO 3302-1, Rubber — Tolerances for products — Part 1: Dimensional tolerances
ISO 3865, Rubber, vulcanized or thermoplastic — Methods of test for staining in contact with organic material
ISO 7619-1, Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 1:
Durometer method (Shore hardness)
ISO 15821, Doorsets and windows — Water-tightness test under dynamic pressure — Cyclonic aspects
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1382 and the following apply.
3.1
structural gasket
building gasket that directly supports glasses, etc. and make
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.