ISO 14317:2006
(Main)Sintered metal materials excluding hardmetals — Determination of compressive yield strength
Sintered metal materials excluding hardmetals — Determination of compressive yield strength
ISO 14317:2006 specifies a method for the determination of the compressive yield strength of sintered metal materials, excluding hardmetals. This method is applicable to sintered materials, excluding hardmetals, that may or may not have been subjected to heat treatment after sintering, and also to materials that have been sized or coined after sintering.
Matériaux métalliques frittés, à l'exclusion des métaux-durs — Détermination de la limite d'élasticité en compression
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 14317
First edition
2006-11-01
Sintered metal materials excluding
hardmetals — Determination of
compressive yield strength
Matériaux métalliques frittés, à l'exclusion des métaux-durs —
Détermination de la limite d'élasticité en compression
Reference number
ISO 14317:2006(E)
©
ISO 2006
---------------------- Page: 1 ----------------------
ISO 14317:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14317:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14317 was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee SC 3,
Sampling and testing methods for sintered metal materials (excluding hardmetals).
© ISO 2006 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 14317:2006(E)
Sintered metal materials excluding hardmetals — Determination
of compressive yield strength
1 Scope
This International Standard specifies a method for the determination of the compressive yield strength of
sintered metal materials, excluding hardmetals.
This method is applicable to sintered materials, excluding hardmetals, that may or may not have been
subjected to heat treatment after sintering, and also to materials that have been sized or coined after sintering.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 7500-1, Metallic
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.