Plywood — Bonding quality — Part 2: Requirements

ISO 12466-2:2007 specifies requirements for determination of bonding quality class of plywood, blockboard, battenboard, and laminboard, bonded with thermosetting resins, according to their intended end uses.

Contreplaqué — Qualité du collage — Partie 2: Exigences

General Information

Publication Date
Technical Committee
Drafting Committee
Current Stage
9093 - International Standard confirmed
Completion Date
Ref Project


Buy Standard

ISO 12466-2:2007 - Plywood -- Bonding quality
English language
4 pages
sale 15% off
sale 15% off

Standards Content (Sample)

STANDARD 12466-2
Second edition

Plywood — Bonding quality —
Part 2:
Contreplaqué — Qualité du collage —
Partie 2: Exigences

Reference number
ISO 12466-2:2007(E)
ISO 2007

---------------------- Page: 1 ----------------------
ISO 12466-2:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 12466-2:2007(E)
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12466-2 was prepared by Technical Committee ISO/TC 89, Wood based panels, Subcommittee SC 3,
This second edition cancels and replaces the first edition (ISO 12466-2:1999) which has been technically
ISO 12466 consists of the following parts, under the general title Plywood — Bonding quality:
⎯ Part 1:Test methods
⎯ Part 2: Requirements

© ISO 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------

Plywood — Bonding quality —
Part 2:
1 Scope
This part of ISO 12466 specifies requirements for determination of bonding quality class of plywood,
blockboard, battenboard, and laminboard, bonded with thermosetting resins, according to their intended end
NOTE Appropriate test methods are specified in ISO 12466-1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 124

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.