ISO 2426-4:2018

Plywood — Classification by surface appearance — Part 4: Palm-plywood

This document specifies the nature and limits of characteristics inherent in palm-plywood and manufacturing defects enabling the visual assessment of the plywood for allocation to an appearance class. This document applies to palm-plywood, the surface veneers of which are made from oil palm trunk.

Contreplaqué — Classification selon l'aspect des faces — Partie 4: Contreplaqué de palmier

General Information

• Status: Published
• Publication Date: 18-Sep-2018
• ICS: 79.060.10 - Plywood
• Technical Committee: ISO/TC 89/SC 3 - Plywood
• Drafting Committee: ISO/TC 89/SC 3 - Plywood
• Current Stage: 9060 - Close of review
• Start Date: 04-Mar-2029

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2426-4
First edition
2018-09
Plywood — Classification by surface
appearance —
Part 4:
Palm-plywood
Contreplaqué — Classification selon l'aspect des faces —
Partie 4: Contreplaqué de palmier
Reference number
ISO 2426-4:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 2426-4:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 2426-4:2018(E)

Contents  Page
Foreword .iv
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Classification by surface appearance . 2
4.1 Appearance classes . 2
4.2 Permissible characteristics and defects . 2
4.2.1 General. 2
4.2.2 Characteristics inherent in palm-plywood . 2
4.2.3 Manufacturing defects . 4
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 2426-4:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Tra
...