SIST EN ISO 4762:2004
(Main)Hexagon socket head cap screws (ISO 4762:2004)
Hexagon socket head cap screws (ISO 4762:2004)
ISO 4762:2004 specifies the characteristics of hexagon socket head cap screws with coarse pitch thread from M1,6 up to and including M64 and product grade A.
Zylinderschrauben mit Innensechskant (ISO 4762:2004)
Diese Internationale Norm legt die Eigenschaften von Zylinderschrauben mit Innensechskant mit Gewinde von M1,6 bis einschließlich M64 in Produktklasse A fest.
Angaben über die ungefähren Gewichte enthält Anhang A.
Werden in besonderen Fällen andere Festlegungen als die in der vorliegenden Internationalen Norm benötigt, so sollten diese den bestehenden Internationalen Normen entnommen werden, z. B. ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 3506-1, ISO 8839 und ISO 4759-1.
Vis a tete cylindrique a six pans creux (ISO 4762:2004)
L'ISO 4762:2004 spécifie les caractéristiques des vis à tête cylindrique à six pans creux, de filetage à pas gros M1,6 à M64 inclus et de grade A. Elle donne également à titre indicatif les masses approximatives de ces vis.
Vijaki z valjasto glavo in notranjim šestkotnikom (ISO 4762:2004)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Vijaki z valjasto glavo in notranjim šestkotnikom (ISO 4762:2004)Zylinderschrauben mit Innensechskant (ISO 4762:2004)Vis a tete cylindrique a six pans creux (ISO 4762:2004)Hexagon socket head cap screws (ISO 4762:2004)21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN ISO 4762:2004SIST EN ISO 4762:2004en01-september-2004SIST EN ISO 4762:2004SLOVENSKI
STANDARDSIST EN ISO 4762:20011DGRPHãþD
SIST EN ISO 4762:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 4762March 2004ICS 21.060.10Supersedes EN ISO 4762:1997English versionHexagon socket head cap screws (ISO 4762:2004)Vis à tête cylindrique à six pans creux (ISO 4762:2004)Zylinderschrauben mit Innensechskant (ISO 4762:2004)This European Standard was approved by CEN on 16 January 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 4762:2004 ESIST EN ISO 4762:2004
EN ISO 4762:2004 (E)2ForewordThis document (EN ISO 4762:2004) has been prepared by Technical Committee ISO/TC 2"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by September 2004, and conflicting nationalstandards shall be withdrawn at the latest by September 2004.This document supersedes EN ISO 4762:1997.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium,Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.Endorsement noticeThe text of ISO 4762:2004 has been approved by CEN as EN ISO 4762:2004 without anymodifications.SIST EN ISO 4762:2004
INTERNATIONALSTANDARDISO4762Fourth edition2004-03-01Reference numberISO4762:2004(E)© ISO2004Hexagon socket head cap screwsVis à tête cylindrique à six pans creux
SIST EN ISO 4762:2004
ISO4762:2004(E)ii© ISO2004–All rights reservedPDF disclaimerThis PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shallnot be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Indownloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariataccepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creationparameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In theunlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.©ISO2004All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below orISO's member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel.+ 41 22 749 01 11Fax+ 41 22 749 09 47E-mailcopyright@iso.orgWebwww.iso.orgPublished in SwitzerlandSIST EN ISO 4762:2004
ISO4762:2004(E)© ISO2004–All rights reservediiiContents Page1Scope . 12Normative references . 13Dimensions . 24Requirements and reference International Standards . 95Designation . 9AnnexA(informative)Masses . 10SIST EN ISO 4762:2004
ISO4762:2004(E)iv© ISO2004–All rights reservedForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the InternationalElectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part2.The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75% of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.ISO4762 was prepared by Technical Committee ISO/TC2, Fasteners.This fourth edition cancels and replaces the third edition (ISO4762:1997), which has been technically revised.SIST EN ISO 4762:2004
INTERNATIONAL STANDARDISO4762:2004(E)© ISO2004–All rights reserved1Hexagon socket head cap screws1ScopeThis International Standard specifies the characteristics of hexagon socket head cap screws with coarse pitchthread from M1,6 up to and including M64 and product gradeA.For approximate masses of screws see AnnexA.If, in special cases, specifications other than those listed in this International Standard are required, they shouldbe selected from existing International Standards, e.g ISO261, ISO888, ISO898-1, ISO965-2. ISO3506-1,ISO8839 and ISO4759-1.2Normative referencesThe following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenced document(including any amendments) applies.ISO225, Fasteners— Bolts, screws, studs and nuts— Symbols and designations of dimensionsISO261, ISO general-purpose metric screw threads— General planISO888, Bolts, screws and studs— Nominal lengths, and thread lengths for general purpose boltsISO898-1, Mechanical properties of fasteners made of carbon steel and alloy steel— Part1: Bolts, screws andstudsISO965-2, ISO general purpose metric screw threads— Tolerances— Part2: Limits of sizes for generalpurpose external and internal screw threads— Medium qualityISO965-3, ISO general purpose metric screw threads— Tolerances— Part3: Deviations for constructionalscrew threadsISO3269, Fasteners— Acceptance inspectionISO3506-1, Mechanical properties of corrosion-resistant stainless-steel fasteners— Part1: Bolts, screws andstudsISO4042, Fasteners— Electroplated coatingsISO4753, Fasteners— Ends of parts with external ISO metric threadISO4759-1, Tolerances for fasteners— Part1: Bolts, screws, studs and nuts— Product grades A, B and CISO6157-1, Fasteners— Surface discontinuities— Part1: Bolts, screws and studs for general requirementsISO6157-3, Fasteners— Surface discon
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.