SIST EN ISO 7436:2024
(Main)Fasteners - Slotted set screws with cup point (ISO 7436:2024)
Fasteners - Slotted set screws with cup point (ISO 7436:2024)
Specifies the characteristics of products with metric dimensions and thread sizes from M 1,6 up to and including M 12 and product grade A; includes specifications with reference to International Standards; tabulates thread sizes M 1,6 up to M 12 with nominal lengths from 2 mm up to 60 mm; gives an example for the designation.
Verbindungselemente - Gewindestifte mit Schlitz und Ringschneide (ISO 7436:2024)
Dieses Dokument legt die Eigenschaften von Gewindestiften mit Schlitz und Ringschneide aus Stahl und nicht
rostendem Stahl mit Regelgewinden M1,6 bis M12 und mit ProduktklasseA fest.
ANMERKUNG Falls in bestimmten Fällen andere Festlegungen benötigt werden, können Härteklassen und nichtros
tende Stahlsorten aus ISO898-5 oder ISO3506-3 und maßliche Alternativen aus ISO888 entnommen werden.
Fixations - Vis sans tête fendues à bout cuvette (ISO 7436:2024)
La présente Norme internationale spécifie les caractéristiques des vis sans tête, fendues, à bout cuvette, de diamètre nominal de filetage M 1,6 à M 12 inclus et de grade A. Si d'autres spécifications sont requises, il est recommandé de les choisir dans les Normes internationales existantes, par exemple ISO 261, ISO 888, ISO 898, ISO 965, ISO 3506, 4759/1.
Vezni elementi - Navojni zatiči z zarezo in končino z obročastim rezilom (ISO 7436:2024)
Standard določa značilnosti izdelkov z metričnimi merami in velikostmi navojev od M 1,6 do vključno M 12 ter razredom izdelave A, vključuje specifikacije s sklicevanjem na mednarodne standarde, v obliki preglednice prikazuje velikosti navojev od M 1,6 do M 12 z nazivno dolžino od 2 mm do 60 mm ter podaja primer za označevanje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Vezni elementi - Navojni zatiči z zarezo in končino z obročastim rezilom (ISO
7436:2024)
Fasteners - Slotted set screws with cup point (ISO 7436:2024)
Verbindungselemente - Gewindestifte mit Schlitz und Ringschneide (ISO 7436:2024)
Fixations - Vis sans tête fendues à bout cuvette (ISO 7436:2024)
Ta slovenski standard je istoveten z: EN ISO 7436:2024
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 7436
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2024
EUROPÄISCHE NORM
ICS 21.060.10 Supersedes EN 27436:1992
English Version
Fasteners - Slotted set screws with cup point (ISO
7436:2024)
Fixations - Vis sans tête fendues à bout cuvette (ISO Verbindungselemente - Gewindestifte mit Schlitz und
7436:2024) Ringschneide (ISO 7436:2024)
This European Standard was approved by CEN on 17 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7436:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 7436:2024) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2024, and conflicting national standards
shall be withdrawn at the latest by December 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 27436:1992.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 7436:2024 has been approved by CEN as EN ISO 7436:2024 without any modification.
International
Standard
ISO 7436
Second edition
Fasteners — Slotted set screws with
2024-06
cup point
Fixations — Vis sans tête fendues à bout cuvette
Reference number
ISO 7436:2024(en) © ISO 2024
ISO 7436:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 7436:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 2
5 Requirements and reference International Standards . 4
6 Marking and labelling . 4
6.1 Marking on product . .4
6.2 Labelling on package .4
7 Designation . 5
Bibliography . 6
iii
ISO 7436:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity as
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.