SIST EN ISO 4766:2024
(Main)Fasteners - Slotted set screws with flat point (ISO 4766:2024)
Fasteners - Slotted set screws with flat point (ISO 4766:2024)
ISO 4766:2011 specifies the characteristics of slotted set screws with flat point and thread sizes from M1,2 to M12 inclusive and product grade A.
Verbindungselemente - Gewindestifte mit Schlitz und Kegelstumpf (ISO 4766:2024)
Dieses Dokument legt die Eigenschaften von Gewindestiften mit Schlitz und Kegelstumpf aus Stahl und nichtrostendem
Stahl mit Regelgewinden M1,2 bis M12 und mit Produktklasse A fest.
ANMERKUNG Falls in bestimmten Fällen andere Festlegungen benötigt werden, können Härteklassen und nichtrostende
Stahlsorten aus ISO 898-5 oder ISO 3506-3 und maßliche Alternativen aus ISO 888 entnommen werden.
Fixations - Vis sans tête fendues à bout plat (ISO 4766:2024)
L'ISO 4766:2011 spécifie les caractéristiques des vis sans tête fendues à bout plat, de grade A et de diamètre de filetage M1,2 à M12 inclus.
Vezni elementi - Navojni zatiči z zarezo in posneto končino (ISO 4766:2024)
Standard ISO 4766:2011 določa značilnosti navojnih zatičev z zarezo in posneto končino, z velikostmi navojev od M 1,2 do vključno M 12 in razredom izdelave A.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Vezni elementi - Navojni zatiči z zarezo in posneto končino (ISO 4766:2024)
Fasteners - Slotted set screws with flat point (ISO 4766:2024)
Verbindungselemente - Gewindestifte mit Schlitz und Kegelstumpf (ISO 4766:2024)
Fixations - Vis sans tête fendues à bout plat (ISO 4766:2024)
Ta slovenski standard je istoveten z: EN ISO 4766:2024
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 4766
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2024
EUROPÄISCHE NORM
ICS 21.060.10 Supersedes EN ISO 4766:2011
English Version
Fasteners - Slotted set screws with flat point (ISO
4766:2024)
Fixations - Vis sans tête fendues à bout plat (ISO Verbindungselemente - Gewindestifte mit Schlitz und
4766:2024) Kegelstumpf (ISO 4766:2024)
This European Standard was approved by CEN on 17 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4766:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 4766:2024) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2024, and conflicting national standards
shall be withdrawn at the latest by December 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4766:2011.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 4766:2024 has been approved by CEN as EN ISO 4766:2024 without any modification.
International
Standard
ISO 4766
Third edition
Fasteners — Slotted set screws with
2024-06
flat point
Fixations — Vis sans tête fendues à bout plat
Reference number
ISO 4766:2024(en) © ISO 2024
ISO 4766:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 4766:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 2
5 Requirements and reference International Standards . 3
6 Marking and labelling . 4
6.1 Marking on product . .4
6.2 Labelling on package .4
7 Designation . 5
Bibliography . 6
iii
ISO 4766:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.