SIST EN ISO 19062-1:2016

Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19062-1:2015)

ISO 19062-1:2015 establishes a system of designation for acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials, which may be used as the basis for specifications.
The types of ABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties:
a)    Vicat softening temperature;
b)    melt mass-flow rate;
c)    Charpy notched impact strength;
d)    tensile modulus;
and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.
ISO 19062-1:2015 is applicable to all acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene) and acrylonitrile and a dispersed elastomeric phase based mainly on polybutadiene, plus other components, in such quantities as specified in the text.
It applies to ABS materials ready for normal use in the form of powder, granules, pellets or chips, unmodified or modified by colorants, additives, fillers, etc.
ISO 19062-1:2015 does not apply to materials
a)    with a Charpy notched impact strength of less than three kilojoules per square metre,
b)    containing less than 50 % by mass of butadiene in the elastomer of the elastomeric phase, and
c)    containing less than 15 % by mass of acrylonitrile in the continuous phase.
It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19062 does not provide engineering data, performance data, or data on processing conditions which may be required to specify a material for a particular application and/or method of processing.
If such additional properties are required, they will be determined in accordance with the test methods specified in ISO 2580‑2, if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1).

Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 19062-1:2015)

1.1 Der vorliegende Teil von ISO 19062 legt ein System für die Bezeichnung von Acrylnitril-Butadien-Styrol-(ABS-)Formmassen fest, das als Grundlage für Spezifikationen angewendet werden darf.
1.2 ABS-Kunststofftypen werden mit Hilfe eines Einteilungssystems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften
a) Vicat-Erweichungstemperatur,
b) Schmelze-Massefließrate,
c) Charpy-Kerbschlagzähigkeit,
d) Zugmodul
und auf Informationen über die Zusammensetzung, vorgesehene Anwendung und/oder Verarbeitungs-verfahren, wichtige Eigenschaften, Additive (Zusatzstoffe), Farbstoffe, Füll- und Verstärkungsstoffe beruht.
1.3 Dieser Teil von ISO 19062 gilt für alle Acrylnitril-Butadien-Styrol-Formmassen mit einer kontinuierlichen Phase vorwiegend auf Basis von Copolymeren des Styrols (und/oder alkylsubstituierten Styrols) und Acrylnitrils und einer dispersen elastomeren Phase vorwiegend auf Basis von Polybutadien mit Beimischung anderer Komponenten in den im Text festgelegten Mengen.
Er gilt für gebrauchsfertige ABS-Formmassen in Form von Pulver, Granulaten, Pellets oder Chips, die mit Farbstoffen, Zusatzstoffen, Füllstoffen usw. modifiziert sind oder nicht.
Dieser Teil von ISO 19062 gilt nicht für Formmassen
a) mit einer Charpy-Kerbschlagzähigkeit von weniger als 3 kJ/m2;
b) mit einem Massenanteil von weniger als 50 % Butadien im Elastomer der elastomeren Phase;
c) mit einem Massenanteil von weniger als 15 % Acrylnitril in der kontinuierlichen Phase.
1.4 Es soll nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise das Gleiche leisten. Dieser Teil von ISO 19062 enthält keine technischen Daten, Leistungsangaben oder Angaben zu Verarbeitungsbedingungen, die notwendig sein können, um eine Formmasse für eine bestimmte Anwen-dung und/oder Verarbeitungsart zu spezifizieren.
Wenn derartige zusätzliche Eigenschaften erforderlich sind, müssen sie nach den in Teil 2 dieser Inter-nationalen Norm (ISO 2580-2) festgelegten Prüfverfahren, soweit geeignet, bestimmt werden.
1.5 Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, dürfen im Datenblock 5 (siehe 3.1) zusätzliche Anforderungen gestellt werden.

Plastiques - Acrylonitrile-butadiène-styrène (ABS) pour moulage et extrusion - Partie 1: Système de désignation et base de spécifications (ISO 19062-1:2015)

ISO 19062-1:2015 établit un système de désignation des matériaux acrylonitrile-styrène-butadiène (ABS) pour moulage et extrusion, qui peut être utilisé comme base pour les spécifications.
Les types de plastique ABS sont différenciés les uns des autres par un système de classification basé sur des niveaux appropriés de propriétés de désignation:
a)    température de ramollissement Vicat;
b)    indice de fluidité à chaud en masse;
c)    résistance au choc Charpy sur éprouvette entaillée;
d)    module de traction;
et des informations concernant la composition, l'application prévue et/ou la méthode de mise en ?uvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renforcement.
La présente partie de l'ISO 19062 est applicable à tous les matériaux acrylonitrile-butadiène-styrène composés d'une phase continue basée principalement sur des copolymères de styrène (et/ou styrène substitué par des groupements alkyles) et d'acrylonitrile et d'une phase élastomérique dispersée principalement basée sur du polybutadiène avec d'autres composants dans les quantités spécifiées dans le texte.
Elle s'applique aux matériaux ABS prêts à une utilisation normale sous la forme de poudre, de grains, de granulés ou de copeaux, non modifiés ou modifiés par des colorants, additifs, charges, etc.
ISO 19062-1:2015 ne s'applique pas aux matériaux
a)    ayant une résistance au choc Charpy sur éprouvette entaillée inférieure à trois kilojoules par mètre carré;
b)    contenant moins de 50 % en masse de butadiène dans l'élastomère de la phase élastomérique, et
c)    contenant moins de 15 % en masse d'acrylonitrile dans la phase continue.
Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. La présente partie de l'ISO 19062 ne comporte pas de données sur la conception, la performance ou les conditions de mise en ?uvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en ?uvre particulière.
Si de telles caractéristiques additionnelles sont nécessaires, elles seront déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 2580‑2, si appropriée.
Afin de prescrire un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en ?uvre reproductible, des exigences additionnelles peuvent être codées dans le bloc de données 5 (voir 3.1).

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz kopolimerov akrilonitril-butadien-stirena(ABS) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 19062-1:2015)

Ta del standarda ISO 19062 določa sistem označevanja materialov za oblikovanje in ekstrudiranje na osnovi akrilonitril-butadien-stirena (ABS), ki jih je mogoče uporabiti kot podlago za specifikacije. Vrste polimernih materialov na osnovi akrilonitril-butadien-stirena se ločujejo glede na sistem razvrščanja, ki temelji na
ustreznih ravneh označevalnih lastnosti:
a) temperaturi zmehčišča po Vicatu;
b) prostorninskem pretoku taline;
c) zarezni udarni žilavosti po Charpyju;
d) nateznih modulih;
ter na informacijah o sestavi, nameravani uporabi in/ali metodi obdelave, pomembnih lastnostih, aditivih, barvilih, polnilih ter materialih za ojačanje.
Ta del standarda ISO 19062 velja za vse materiale iz akrilonitril-butadien-stirena, sestavljenih iz neprekinjene faze, ki v glavnem temelji na kopolimerih stirena (in/ali stirena, zamenjanega z alkilom) in akrilonitrila ter razpršene elastomerne faze, ki v glavnem temelji na polibutadienu, in druge komponente
v količinah, ki so določene v besedilu.
Uporablja se za materiale na osnovi akrilonitril-butadien-stirena v obliki praška, granul ali peletov, pripravljene za običajno uporabo, nespremenjene ali spremenjene z barvili, aditivi, polnili itd.
Ta del standarda ISO 19062 se ne uporablja za materiale
a) z zarezno udarno žilavostjo po Charpyju, ki znaša manj kot tri kilodžule na kvadratni meter,
b) z masnim deležem butadiena v polnilu v elastomeru elastomerne faze, manjšim od 50 % in
c) z masnim deležem akrilonitrila v neprekinjeni fazi, manjšim od 15 %.
Materiali z enako oznako nimajo nujno tudi enakih lastnosti. Ta del standarda ISO 19062 ne zagotavlja inženirskih podatkov, podatkov o delovanju ali podatkov o pogojih obdelave, ki so lahko potrebni za določitev materiala za določeno uporabo in/ali metodo obdelave.
Če so take dodatne lastnosti zahtevane, bodo določene v skladu s preskusnimi metodami iz standarda ISO 2580-2, če je to primerno. Da bi se določil termoplastični material za določeno uporabo ali da bi se zagotovila obnovljiva obdelava, se lahko v podatkovnem bloku 5 navedejo dodatne zahteve (glej točko 3.1).

General Information

• Status: Published
• Public Enquiry End Date: 29-May-2014
• Publication Date: 20-Dec-2015
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 16-Dec-2015
• Due Date: 20-Feb-2016
• Completion Date: 21-Dec-2015
• Ref Project: EN ISO 19062-1:2015 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19062-1:2015)

Relations

• Replaces: SIST EN ISO 2580-1:2003 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002)
• Effective Date: 01-Feb-2016
• Replaces: SIST EN ISO 2580-1:2003 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19062-1:2016
01-februar-2016
1DGRPHãþD
SIST EN ISO 2580-1:2003
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]NRSROLPHURY
DNULORQLWULOEXWDGLHQVWLUHQD$%6GHO6LVWHPR]QDþHYDQMDLQSRGODJH]D
VSHFLILNDFLMH,62
Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part
1: Designation system and basis for specifications (ISO 19062-1:2015)
Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 19062-1:2015)
Plastiques - Acrylonitrile-butadiène-styrène (ABS) pour moulage et extrusion - Partie 1:
Système de désignation et base de spécifications (ISO 19062-1:2015)
Ta slovenski standard je istoveten z: EN ISO 19062-1:2015
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 19062-1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 19062-1:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 19062-1:2016


EN ISO 19062-1
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2015
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 2580-1:2002
English Version

Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding
and extrusion materials - Part 1: Designation system and
basis for specifications (ISO 19062-1:2015)
Plastiques - Acrylonitrile-butadiène-styrène (ABS) Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-
pour moulage et extrusion - Partie 1 : Système de Formmassen - Teil 1: Bezeichnungssystem und Basis
désignation et base de spécification (ISO 19062- für Spezifikationen (ISO 19062-1:2015)
1:2015)
This European Standard was approved by CEN on 26 September 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19062-1:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 19062-1:2016
EN ISO 19062-1:2015 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 19062-1:2016
EN ISO 19062-1:2015 (E)
European foreword
This document (EN ISO 19062-1:2015) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 2580-1:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19062-1:2015 has been approved by CEN as EN ISO 19062-1:2015 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 19062-1:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 19062-1:2016
INTERNATIONAL ISO
STANDARD 19062-1
First edition
2015-11-15
Plastics — Acrylonitrile-butadiene-
styrene (ABS) moulding and
extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Acrylonitrile-butadiène-styrène (ABS) pour moulage
et extrusion —
Partie 1: Système de désignation et base de spécifications
Reference number
ISO 19062-1:2015(E)
©
ISO 2015

---------------------- Page: 7 ----------------------

SIST EN ISO 19062-1:2016
ISO 19062-1:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 19062-1:2016
ISO 19062-1:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Designation system . 2
3.1 General . 2
3.2 Data block 1 . 2
3.3 Data block 2 . 3
3.4 Data block 3 . 4
3.5 Data block 4 . 5
3.5.1 Vicat softening temperature . 5
3.5.2 Melt mass-flow rate . 6
3.5.3 Charpy notched impact strength. 6
3.5.4 Tensile modulus . 6
3.6 Data block 5 . 7
4 Examples of designations . 7
© ISO 2015 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 19062-1:2016
ISO 19062-1:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 19062-1 cancels and replaces ISO 2580-1:2002, which has been technically
revised to introduce a new designation system.
The revised designation system is published under a new ISO number, as many existing documents
refer to ISO 2580-1. If the existing ISO 2580-1 would be replaced by the new designation system, these
documents would refer to the incorrect designation system.
In order to give users time to switch from ISO 2580-1 to ISO 19062-1, any designation system according
to ISO 2580-1 is to be phased out in 5 to 10 years. During this period, ISO 2580-2 will effectively be Part
2 of this International Standard.
ISO 19062 consists of the following parts, under the general title Plastics — Acrylonitrile-butadiene-
styrene (ABS) moulding and extrusion materials:
— Part 1: Designation system and basis for specifications
iv © ISO 2015 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 19062-1:2016
ISO 19062-1:2015(E)

Introduction
ISO 2580-1 is complex and does not fit with daily practice anymore. In practice, ISO 1043 (all parts)
and ISO 11469 are, in combination, “improperly” being used as a designation system for, e.g. marking.
The aim of this International Standard is to simplify the data block system and to connect more to
ISO 1043 (all parts) and ISO 11469, where the first two blocks are used for generic identification and
marking of products.
© ISO 2015 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 19062-1:2016

---------------------- Page: 12 ----------------------

SIST EN ISO 19062-1:2016
INTERNATIONAL STANDARD ISO 19062-1:2015(E)
Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding
and extrusion materials —
Part 1:
Designation system and basis for specifications
1 Scope
This part of ISO 19062 establishes a system of designation for acrylonitrile-butadiene-styrene (ABS)
moulding and extrusion materials, which may be used as the basis for specifications.
The types of ABS plastic are differentiated from each other by a classification system based on
appropriate levels of the designatory properties:
a) Vicat softening temperature;
b) melt mass-flow rate;
c) Charpy notched impact strength;
d) tensile modulus;
and on information about composition, intended application and/or method of processing, important
properties, additives, colorants, fillers, and reinforcing materials.
This part of ISO 19062 is applicable to all acrylonitrile-butadiene-styrene materi
...