SIST EN ISO 8986-1:2010
(Main)Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8986-1:2009)
Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8986-1:2009)
This part of ISO 8986 establishes a system of designation for polybutene-1 (PB-1) thermoplastic materials which may be used as the basis for specifications. For the sake of simplicity, the designation polybutene and the abbreviation PB are used in both parts of ISO 8986. The types of polybutene plastics are differentiated from each other by a classification system based on appropriate levels of the designatory property melt volume-flow rate and on information about basic polymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. This part of ISO 8986 is applicable to all butene homopolymers and to copolymers of butene with a maximum content of other 1-olefinic monomers of less than 50 % by mass and with a content of non-olefinic monomers with functional groups up to a maximum of 1 % by mass. It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc. It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 8986 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1).
Kunststoffe - Polybuten-1 (PB-1)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 8986-1:2009)
1.1 In diesem Teil von ISO 8986 wird ein Bezeichnungssystem für thermoplastische Polybuten-1 (PB 1) Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann. Der Einfachheit halber wird in diesem Dokument die Bezeichnung Polybuten mit der Abkürzung PB verwendet.
1.2 PB Formmasse Typen werden mit Hilfe eines Einteilungssystems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaft
a) Schmelze Massefließrate
und Informationen über grundlegende Polymer Parameter, vorgesehene Anwendung und/oder Verarbeitungsverfahren, wichtige Eigenschaften, Additive, Farbstoffe, Füll und Verstärkungsstoffe beruht.
1.3 Dieser Teil von ISO 8986 ist anwendbar für alle Buten Homopolymere und Copolymere des Butens mit einem Massenanteil anderer 1 Olefine von weniger als 50 % und einem Massenanteil an nichtolefinischen Monomeren mit funktionellen Gruppen von maximal 1 %.
Er gilt für gebrauchsfertige Formmassen in der Form von Pulver, Grieß oder Granulat, modifiziert oder nicht modifiziert mit Farbstoffen, Additiven, Füllstoffen usw.
1.4 Es soll nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise auch Gleiches leisten. Dieser Teil von ISO 8986 enthält keine technischen Daten, Leistungsangaben oder Verarbeitungsbedingungen, die notwendig sein können, um eine Formmasse für eine spezielle Anwendung und/oder eine bestimmte Verarbeitungsart zu spezifizieren.
Ein Teil 2 dieser Internationalen Norm, der zur Herstellung der Probekörper und der Bestimmung von Eigenschaften dient, steht zur Verfügung.
1.5 Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, dürfen zusätzliche Anforderungen im Daten Block 5 festgelegt werden (siehe Abschnitt 3, einleitender Absatz).
Plastiques - Matériaux à base de polybutène-1 (PB-1) pour moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO 8986-1:2009)
L'ISO 8986-1:2009 établit un système de désignation des matériaux thermoplastiques polybutène (PB-1) qui peut être utilisé comme base pour les spécifications.
Les types de plastiques polybutène sont différenciés les uns des autres par un système de classification basé sur des niveaux appropriés de la propriété de désignation indice de fluidité à chaud en volume et sur des informations concernant certains paramètres du polymère de base, l'application prévue et/ou la méthode de mise en œuvre, les propriétés importantes, les additifs, colorants, matériaux de charge et de renforcement.
L'ISO 8986-1:2009 est applicable à tous les homopolymères de butène et aux copolymères de butène contenant moins de 50 % en masse d'autres monomères 1-oléfiniques et moins de 1 % en masse d'autres monomères non oléfiniques avec des groupes fonctionnels.
Elle s'applique aux matériaux prêts à l'emploi sous forme de poudres, grains ou granulés, non modifiés ou modifiés par des colorants, additifs, charges, etc.
Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz polibutena-1 (PB-1) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 8986-1:2009)
Ta del ISO 8986 vzpostavlja sistem označevanja za termoplastne materiale iz polibutena-1 (PB-1), ki se lahko uporablja kot osnova za specifikacije. Zaradi enostavnosti se v obeh delih ISO 8986 uporabljata oznaka polibuten in okrajšava PB. Vrste polimernih materialov iz polibutena se med seboj ločijo s sistemom razvrščanja na osnovi ustreznih ravni označevalne lastnosti volumskega pretoka taline in podatkov o osnovnih polimernih parametrih, po namenu uporabe in/ali metodi obdelave, po pomembnih lastnosti, aditivih, barvilih, polnilih in ojačitvenih materialih. Ta del ISO 8986 velja za vse homopolimere iz butena in kopolimere iz butena z največjo vsebnostjo drugih 1-olefinskih monomerov pod 50 % masnega deleža in z vsebnostjo neolefinskih monomerov s funkcionalnimi skupinami do največ 1 % masnega deleža. Velja za materiale, pripravljene za običajno uporabo v obliki praška, granul ali peletov, in za materiale, ki so nespremenjeni ali spremenjeni z barvili, aditivi, polnili itd. Ne pomeni, da imajo materiali z enako oznako nujno tudi enake zmogljivosti. Ta del ISO 8986 ne zagotavlja podatkov o inženiringu, podatkov o zmogljivosti ali podatkov o pogojih obdelave, ki so morda potrebni za specifikacijo materiala za določeno uporabo in/ali metodo obdelave. Za specifikacijo termoplastnega materiala za določeno uporabo ali za zagotavljanje ponovljive obdelave so v podatkovnem sklopu 5 (glej točko 3.1) lahko podane dodatne zahteve.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8986-1:2010
01-februar-2010
1DGRPHãþD
SIST EN ISO 8986-1:2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]SROLEXWHQD 3%
GHO 6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH ,62
Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation
system and basis for specifications (ISO 8986-1:2009)
Kunststoffe - Polybuten-1 (PB-1)-Formmassen - Teil 1: Bezeichnungssystem und Basis
für Spezifikationen (ISO 8986-1:2009)
Plastiques - Matériaux à base de polybutène-1 (PB-1) pour moulage et extrusion - Partie
1: Système de désignation et base de spécification (ISO 8986-1:2009)
Ta slovenski standard je istoveten z: EN ISO 8986-1:2009
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 8986-1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8986-1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 8986-1:2010
EUROPEAN STANDARD
EN ISO 8986-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2009
ICS 83.080.20 Supersedes EN ISO 8986-1:1999
English Version
Plastics - Polybutene-1 (PB-1) moulding and extrusion materials
- Part 1: Designation system and basis for specifications (ISO
8986-1:2009)
Plastiques - Matériaux à base de polybutène-1 (PB-1) pour Kunststoffe - Polybuten-1 (PB-1)-Formmassen - Teil 1:
moulage et extrusion - Partie 1: Système de désignation et Bezeichnungssystem und Basis für Spezifikationen (ISO
base de spécification (ISO 8986-1:2009) 8986-1:2009)
This European Standard was approved by CEN on 21 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8986-1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8986-1:2010
EN ISO 8986-1:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8986-1:2010
EN ISO 8986-1:2009 (E)
Foreword
This document (EN ISO 8986-1:2009) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the
latest by May 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8986-1:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 8986-1:2009 has been approved by CEN as a EN ISO 8986-1:2009 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8986-1:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 8986-1:2010
INTERNATIONAL ISO
STANDARD 8986-1
Second edition
2009-11-15
Plastics — Polybutene-1 (PB-1) moulding
and extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux à base de polybutène-1 (PB-1) pour moulage
et extrusion —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 8986-1:2009(E)
©
ISO 2009
---------------------- Page: 7 ----------------------
SIST EN ISO 8986-1:2010
ISO 8986-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8986-1:2010
ISO 8986-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8986-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This second edition cancels and replaces the first edition (ISO 8986-1:1993), which has been technically
revised. The main changes are as follows:
⎯ it has been made clear that the standard concerns polybutene-1 as opposed to its isomer polyisobutene;
⎯ density has been deleted as a designatory property;
⎯ the only other designatory property, melt mass-flow rate (MFR), has been replaced by melt volume-flow
rate (MVR);
⎯ 190 °C/5,0 kg has been added to the sets of conditions which can be used for the measurement of MVR.
ISO 8986 consists of the following parts, under the general title Plastics — Polybutene-1 (PB-1) moulding and
extrusion materials:
⎯ Part 1: Designation system and basis for specifications
⎯ Part 2: Preparation of test specimens and determination of properties
© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 8986-1:2010
---------------------- Page: 10 ----------------------
SIST EN ISO 8986-1:2010
INTERNATIONAL STANDARD ISO 8986-1:2009(E)
Plastics — Polybutene-1 (PB-1) moulding and extrusion
materials —
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of ISO 8986 establishes a system of designation for polybutene-1 (PB-1) thermoplastic
materials which may be used as the basis for specifications. For the sake of simplicity, the designation
polybutene and the abbreviation PB are used in both parts of ISO 8986.
1.2 The types of polybutene plastics are differentiated from each other by a classification system based on
appropriate levels of the designatory property melt volume-fl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.