SIST EN ISO 15527:2013
(Main)Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2010)
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2010)
This International Standard specifies the requirements and test methods for solid flat compression-moulded sheets of polyethylene (PE-UHMW and PE-HD, see ISO 1043-1) without fillers or reinforcing materials. It applies only to thicknesses from 10 mm to 200 mm.
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen und Prüfverfahren (ISO 15527:2010)
Diese Internationale Norm legt die Anforderungen und Prüfverfahren an massive ebene gepresste Tafeln aus Polyethylen (PE UHMW und PE HD, siehe ISO 1043 1) ohne Füll- oder Verstärkungsstoffe fest. Sie gilt nur für Tafeldicken von 10 mm bis 200 mm.
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) - Exigences et méthodes d'essai (ISO 15527:2010)
L'ISO 15527:2010 spécifie les exigences et les méthodes d'essai pour les plaques moulées par compression, compactes et planes, en polyéthylène (PE-UHMW et PE-HD) sans charges ou matériaux de renforcement. Elle s'applique uniquement aux plaques de 10 mm à 200 mm d'épaisseur.
Polimerni materiali - Kompresijsko brizgane polietilenske plošče (PE-UHMW, PE-HD) - Zahteve in preskusne metode (ISO 15527:2010)
Ta mednarodni standard določa zahteve in preskusne metode za masivne ravne kompresijsko brizgane polietilenske plošče (PE-UHMW in PE-HD, glej standard ISO 1043-1) brez polnil ali materialov za ojačanje. Uporablja se le za debeline od 10 mm do 200 mm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15527:2013
01-maj-2013
3ROLPHUQLPDWHULDOL.RPSUHVLMVNREUL]JDQHSROLHWLOHQVNHSORãþH 3(8+0:3(
+' =DKWHYHLQSUHVNXVQHPHWRGH ,62
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) -
Requirements and test methods (ISO 15527:2010)
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen
und Prüfverfahren (ISO 15527:2010)
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) -
Exigences et méthodes d'essai (ISO 15527:2010)
Ta slovenski standard je istoveten z: EN ISO 15527:2013
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 15527:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15527:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 15527:2013
EUROPEAN STANDARD
EN ISO 15527
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2013
ICS 83.140.10
English Version
Plastics - Compression-moulded sheets of polyethylene (PE-
UHMW, PE-HD) - Requirements and test methods (ISO
15527:2010)
Plastiques - Plaques moulées par compression en Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-
polyéthylène (PE-UHMW, PE-HD) - Exigences et méthodes UHMW, PE-HD) - Anforderungen und Prüfverfahren (ISO
d'essai (ISO 15527:2010) 15527:2010)
This European Standard was approved by CEN on 24 February 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15527:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15527:2013
EN ISO 15527:2013 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15527:2013
EN ISO 15527:2013 (E)
Foreword
The text of ISO 15527:2010 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 15527:2013 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2013, and conflicting national standards shall be
withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15527:2010 has been approved by CEN as EN ISO 15527:2013 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15527:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 15527:2013
INTERNATIONAL ISO
STANDARD 15527
Second edition
2010-10-01
Plastics — Compression-moulded sheets
of polyethylene (PE-UHMW, PE-HD) —
Requirements and test methods
Plastiques — Plaques moulées par compression en polyéthylène
(PE-UHMW, PE-HD) — Exigences et méthodes d'essai
Reference number
ISO 15527:2010(E)
©
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 15527:2013
ISO 15527:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15527:2013
ISO 15527:2010(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Material .1
4 Requirements.2
4.1 Appearance .2
4.2 Dimensional tolerances .2
4.3 Properties.3
5 Test methods .4
5.1 Test specimens.4
5.2 Delivery condition .5
5.3 Appearance .5
5.4 Dimensions .5
5.5 Density.5
5.6 Determination of abrasion properties .5
5.7 Tensile stress at yield, σ , and tensile strain at yield, ε .5
y y
5.8 Modulus of elasticity in tension, E .5
t
5.9 Impact strength of notched specimens .6
5.10 Melt mass-flow rate (MFR).6
6 Designation .6
7 Marking.6
Annex A (normative) Requirements for rectangularity.7
Annex B (normative) Determination of abrasion properties .8
Annex C (informative) Example of apparatus for the determination of abrasion properties.10
© ISO 2010 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 15527:2013
ISO 15527:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15527 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This second edition cancels and replaces the first edition (ISO 15527:2007), of which it constitutes a minor
revision (the requirements given in Table 2 for the abrasion properties have been modified and in 5.9.2
ISO 179-1, rather than ISO 11542-2, is now used to determine the Charpy impact strength).
iv © ISO 2010 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 15527:2013
INTERNATIONAL STANDARD ISO 15527:2010(E)
Plastics — Compression-moulded sheets of polyethylene
(PE-UHMW, PE-HD) — Requirements and test methods
1 Scope
This International Standard specifies the requirements and test methods for solid flat compression-moulded
sheets of polyethylene (PE-UHMW and PE-HD, see ISO 1043-1) without fillers or reinforcing materials. It
applies only to thicknesses from 10 mm to 200 mm.
2 Normative references
T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.