SIST EN ISO 21003-2:2009/A1:2011
(Amendment)Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes - Amendment 1 (ISO 21003-2:2008/Amd 1:2011)
Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes - Amendment 1 (ISO 21003-2:2008/Amd 1:2011)
This part of ISO 21003 specifies the characteristics of pipes for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 21003-1).The stress designed plastic materials are: PE-RT, PE-X, PB, PP, PVC-C.
This standard covers a range of service conditions (application classes) and design pressure classes. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with the other parts of ISO 21003 it is applicable to multilayer pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation innerhalb von Gebäuden - Teil 2: Rohre - Änderung 1 (ISO 21003-2:2008/Amd 1:2011)
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à l'intérieur des bâtiments - Partie 2: Tubes - Amendement 1 (ISO 21003-2:2008/Amd 1:2011)
Večslojni cevni sistemi za napeljave z vročo in hladno vodo v stavbah - 2. del: Cevi - Dopolnilo A1 (ISO 21003-2:2008/Amd 1:2011)
Ta del ISO 21003 določa značilnosti cevi za večslojne cevne sisteme, ki se uporabljajo za napeljave z vročo in hladno vodo v stavbah za prenos vode, ne glede na to, ali je namenjena prehrani ljudi (gospodinjski sistemi), in za grelne sisteme, pod računskimi tlaki in pri temperaturah v skladu z razredom uporabe (glej preglednico 1 iz ISO 21003-1). Polimerni materiali, načrtovani za obremenitve, so: PE-RT, PE-X, PB, PP, PVC-C.
Ta standard zajema razpon pogojev delovanja (razrede uporabe) in razrede računskega tlaka. Določa tudi preskusne parametre za preskusne metode, navedene v tem standardu. V povezavi z drugimi deli ISO 21003 velja za večslojne cevi, fitinge in njihove spoje ter spoje s komponentami iz drugih polimernih in nepolimernih materialov, ki se uporabljajo za napeljave z vročo in hladno vodo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 21003-2:2009/oprA1:2010
01-maj-2010
9HþVORMQLFHYQLVLVWHPL]DQDSHOMDYH]YURþRLQKODGQRYRGRYVWDYEDKGHO &HYL
,62 '$0
Multilayer piping systems for hot and cold water installations inside buildings - Part 2:
Pipes (ISO 21003-2:2008/DAM 1:2010)
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation
innerhalb von Gebäuden - Teil 2: Rohre - Änderung 1 (ISO 21003-2:2008/DAM 1:2010)
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à
l'intérieur des bâtiments - Partie 2: Tubes (ISO 21003-2:2008/DAM 1:2010)
Ta slovenski standard je istoveten z: EN ISO 21003-2:2008/prA1
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 21003-2:2009/oprA1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 21003-2:2009/oprA1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 21003-2:2009/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN ISO 21003-2:2008
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
March 2010
ICS 91.140.60; 23.040.20
English Version
Multilayer piping systems for hot and cold water installations
inside buildings - Part 2: Pipes (ISO 21003-2:2008/DAM 1:2010)
Systèmes de canalisations multicouches pour installations Mehrschichtverbund-Rohrleitungssysteme für die Warm-
d'eau chaude et froide à l'intérieur des bâtiments - Partie 2: und Kaltwasserinstallation innerhalb von Gebäuden - Teil 2:
Tubes (ISO 21003-2:2008/DAM 1:2010) Rohre - Änderung 1 (ISO 21003-2:2008/DAM 1:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
This draft amendment A1, if approved, will modify the European Standard EN ISO 21003-2:2008. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21003-2:2008/prA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 21003-2:2009/oprA1:2010
EN ISO 21003-2:2008/prA1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 21003-2:2009/oprA1:2010
EN ISO 21003-2:2008/prA1:2010 (E)
Foreword
This document (EN ISO 21003-2:2008/prA1:2010) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 21003-2:2008/DAM 1:2010 has been approved by CEN as a EN ISO 21003-2:2008/prA1:2010
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 21003-2:2009/oprA1:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 21003-2:2009/oprA1:2010
DRAFT AMENDMENT ISO 21003-2:2008/DAmd 1
ISO/TC 138/SC 2 Secretariat: SNV
Voting begins on: Voting terminates on:
2010-03-25 2010-08-25
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Multilayer piping systems for hot and cold water installations
inside buildings —
Part 2:
Pipes
AMENDMENT 1
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à l'intérieur des bâtiments —
Partie 2: Tubes
AMENDEMENT 1
ICS 23.040.20; 91.140.60
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-
...
SLOVENSKI STANDARD
SIST EN ISO 21003-2:2009/A1:2011
01-december-2011
9HþVORMQLFHYQLVLVWHPL]DQDSHOMDYH]YURþRLQKODGQRYRGRYVWDYEDKGHO &HYL
'RSROQLOR$ ,62 $PG
Multilayer piping systems for hot and cold water installations inside buildings - Part 2:
Pipes - Amendment 1 (ISO 21003-2:2008/Amd 1:2011)
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation
innerhalb von Gebäuden - Teil 2: Rohre - Änderung 1 (ISO 21003-2:2008/Amd 1:2011)
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à
l'intérieur des bâtiments - Partie 2: Tubes - Amendement 1 (ISO 21003-2:2008/Amd
1:2011)
Ta slovenski standard je istoveten z: EN ISO 21003-2:2008/A1:2011
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 21003-2:2009/A1:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 21003-2:2009/A1:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 21003-2:2009/A1:2011
EUROPEAN STANDARD
EN ISO 21003-2:2008/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 91.140.60; 23.040.20
English Version
Multilayer piping systems for hot and cold water installations
inside buildings - Part 2: Pipes - Amendment 1 (ISO 21003-
2:2008/Amd 1:2011)
Systèmes de canalisations multicouches pour installations Mehrschichtverbund-Rohrleitungssysteme für die Warm-
d'eau chaude et froide à l'intérieur des bâtiments - Partie 2: und Kaltwasserinstallation innerhalb von Gebäuden - Teil 2:
Tubes - Amendement 1 (ISO 21003-2:2008/Amd 1:2011) Rohre - Änderung 1 (ISO 21003-2:2008/Amd 1:2011)
This amendment A1 modifies the European Standard EN ISO 21003-2:2008; it was approved by CEN on 14 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21003-2:2008/A1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 21003-2:2009/A1:2011
EN ISO 21003-2:2008/A1:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 21003-2:2009/A1:2011
EN ISO 21003-2:2008/A1:2011 (E)
Foreword
This document (EN ISO 21003-2:2008/A1:2011) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.