IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 18: E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)

The present document applies to the following radio equipment type:
1) Multi-Standard Radio capable Base stations (E-UTRA, UTRA, GSM/EDGE).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
NOTE 1: For BS capable of multi-band operation, the supported operating bands may belong to different Band Categories.The present document covers requirements for multi-RAT capable E-UTRA, UTRA and GSM/EDGE MSR Base Stations for 3GPP™ Release 9, 10 and 11. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) [i.2], Article 3.2, which states that "….. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive may apply to equipment within the scope of the present document. NOTE 2: A list of such ENs is included on the web site http://www.newapproach.org.

Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 18. del: Multi-Standard Radio (E-UTRA, UTRA in GSM/EDGE) bazne postaje (BS)

Ta dokument se uporablja za radijsko opremo naslednje vrste:
1. Bazne postaje, ki podpirajo multi standard radio (E-UTRA, UTRA, GSM/EDGE).
Radijska oprema teh vrst lahko deluje v vseh delih frekvenčnih pasov iz tabele 1-1.
OPOMBA 1: Pri baznih postajah, ki lahko delujejo v več pasovih, lahko podprti pasovi spadajo v različne kategorije pasov. V tem dokumentu so zajete zahteve za bazne postaje E-UTRA, UTRA in GSM/EDGE z multi tehnologijo radijskega dostopa za izdaje 9, 10 in 11 standarda 3GPP™. Ta dokument zajema določbe člena 3.2 Direktive 1999/5/ES [i.2] (direktive R&TTE) [i.2], ki navaja, da »[...] mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja«. Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE. OPOMBA 2: Seznam tovrstnih evropskih standardov je na voljo na spletnem mestu http://www.newapproach.org.

General Information

Status
Published
Publication Date
13-Jul-2014
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
07-Jul-2014
Due Date
11-Sep-2014
Completion Date
14-Jul-2014
Mandate

Buy Standard

Standard
EN 301 908-18 V7.1.2:2014
English language
62 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 301 908-18 V7.1.2 (2014-07) - IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 18: E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)
English language
62 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.*60('*(IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 18: E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-18 Version 7.1.2SIST EN 301 908-18 V7.1.2:2014en01-september-2014SIST EN 301 908-18 V7.1.2:2014SLOVENSKI
STANDARD



SIST EN 301 908-18 V7.1.2:2014



bqéf=bk=màk=sàr-kr=sq.k.l=blàk4-àqc=IMT cellular networks; Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive; Part 18: E-UTRA, UTRA and GSM/EDGE
Multi-Standard Radio (MSR) Base Station (BS) =
=HARMONIZED EUROPEAN STANDARD SIST EN 301 908-18 V7.1.2:2014



ETSI ETSI EN 301 908-18 V7.1.2 (2014-07)2
Reference obkiàéd-qcbé-àkk-kra=Keywords mdf=mdmmf=cellularf=digitalf=badbf=b-rqoAf=déàf=fàqf=fàq-Advancedf=fàq-làààf=iqbf=mobilef=àéof=radiof=regulationf=ràqéf=rqoAf=tCaàA=ETSI éoà=ooute=des=iucioles=c-àéslk=éoéhia=Antiéolis=Cedex=-=coAkCb =qel.t=emm=4=sl=s4=4l=àà===caxt=emm=4=sm=éo=4q=ké==éiret=k°=m4r=élm=oél=àààkq=-=kAc=q4l=C=Association=à=but=non=lucratif=enregistrée=à=la=éous-mréfecture=de=drasse=bàéc=k°=qràmirr==Important notice qhe=éresent=document=can=be=downloaded=fromt=httétiiwww.etsi.org=qhe=éresent=document=may=be=made=available=in=electronic=versions=andior=in=érint.=qhe=content=of=any=electronic=andior=érint=versions=of=the=éresent=document=shall=not=be=modified=without=the=érior=written=authorization=of=bqéf.=fn=case=of=any=existing=or=éerceived=difference=in=contents=between=such=versions=andior=in=érintf=the=only=érevailing=document=is=the=érint=of=the=mortable=aocument=cormat=bmacc=version=keét=on=a=séecific=network=drive=within=bqéf=éecretariat.=rsers=of=the=éresent=document=should=be=aware=that=the=document=may=be=subàect=to=revision=or=change=of=status.=fnformation=on=the=current=status=of=this=and=other=bqéf=documents=is=available=at=httétiiéortal.etsi.orgitbistatusistatus.asé=ff=you=find=errors=in=the=éresent=documentf=élease=send=your=comment=to=one=of=the=following=servicest=httétiiéortal.etsi.orgichaircoribqéf_suééort.asé=Copyright Notification ko=éart=may=be=reéroduced=or=utilized=in=any=form=or=by=any=meansf=electronic=or=mechanicalf=including=éhotocoéying=and=microfilm=exceét=as=authorized=by=written=éermission=of=bqéf.=qhe=content=of=the=mac=version=shall=not=be=modified=without=the=written=authorization=of=bqéf.=qhe=coéyright=and=the=foregoing=restriction=extend=to=reéroduction=in=all=media.==©=buroéean=qelecommunications=étandards=fnstitute=làk4.=All=rights=reserved.==DECTqàf=PLUGTESTSqàf=UMTSqà=and=the=bqéf=logo=are=qrade=àarks=of=bqéf=registered=for=the=benefit=of=its=àembers.=3GPPqà=and=LTE™=are=qrade=àarks=of=bqéf=registered=for=the=benefit=of=its=àembers=and=of=the=mdmm=lrganizational=martners.=GSM®=and=the=déà=logo=are=qrade=àarks=registered=and=owned=by=the=déà=Association.=SIST EN 301 908-18 V7.1.2:2014



ETSI ETSI EN 301 908-18 V7.1.2 (2014-07)3Contents=Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 Introduction . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 8 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 11 3.3 Abbreviations . 12 4 Technical requirements specifications . 13 4.1 Environmental profile . 13 4.2 Conformance requirements . 13 4.2.1 Introduction. 13 4.2.2 Operating band unwanted emissions . 15 4.2.2.1 Definition . 15 4.2.2.2 Limits . 16 4.2.2.2.1 Limits for Band Categories 1 and 3 . 16 4.2.2.2.2 Limits for Band Category 2 . 20 4.2.2.2.3 Limits for GSM/EDGE single-RAT operation . 25 4.2.2.2.4 Limits for protection of DTT . 25 4.2.2.2.5 Limits for co-existence with services in adjacent frequency bands . 25 4.2.2.3 Conformance . 26 4.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 26 4.2.3.1 Definition . 26 4.2.3.2 Limits . 26 4.2.3.2.1 E-UTRA limits . 26 4.2.3.2.2 UTRA FDD limits . 26 4.2.3.2.3 UTRA TDD limits . 26 4.2.3.2.4 Cumulative ACLR requirement in non-contiguous spectrum . 27 4.2.3.3 Conformance . 28 4.2.4 Transmitter spurious emissions . 28 4.2.4.1 Limits . 28 4.2.4.1.1 Spurious emissions . 28 4.2.4.1.2 Additional spurious emissions requirement for BC2 . 28 4.2.4.1.3 Co-existence with other systems . 29 4.2.4.1.4 Protection of the BS receiver of own or different BS . 30 4.2.4.2 Conformance . 31 4.2.5 Base station maximum output power . 31 4.2.5.1 Definition . 31 4.2.5.2 Limits . 31 4.2.5.3 Conformance . 31 4.2.6 Transmit intermodulation . 31 4.2.6.1 Definition . 31 4.2.6.2 Limits . 32 4.2.6.2.1 General limits . 32 4.2.6.2.2 Additional limits (BC1 and BC2) . 32 4.2.6.2.3 Additional limits (BC3) . 33 4.2.6.3 Conformance . 33 4.2.7 Receiver spurious emissions . 33 4.2.7.1 Definition . 33 SIST EN 301 908-18 V7.1.2:2014



ETSI ETSI EN 301 908-18 V7.1.2 (2014-07)44.2.7.2 Limits . 34 4.2.7.2.1 General limits . 34 4.2.7.2.2 Additional limits for BC2 . 34 4.2.7.3 Conformance . 34 4.2.8 In-band blocking . 34 4.2.8.1 Definition . 34 4.2.8.2 Limits . 35 4.2.8.2.1 General limits . 35 4.2.8.2.2 Additional BC3 blocking limits . 36 4.2.8.3 Conformance . 36 4.2.9 Out-of-band blocking . 36 4.2.9.1 Definition . 36 4.2.9.2 Limits . 36 4.2.9.3 Conformance . 37 4.2.10 Receiver intermodulation characteristics . 37 4.2.10.1 Definition . 37 4.2.10.2 Limits . 37 4.2.10.2.1 General intermodulation limits . 37 4.2.10.2.2 General narrowband intermodulation limits . 38 4.2.10.2.3 Additional narrowband intermodulation limits for GSM/EDGE . 40 4.2.10.3 Conformance . 40 4.2.11 Narrowband blocking . 40 4.2.11.1 Definition . 40 4.2.11.2 Limits . 40 4.2.11.2.1 General limits . 40 4.2.11.2.2 Additional limits for GSM/EDGE . 41 4.2.11.2.3 GSM/EDGE limits for AM suppression . 41 4.2.11.3 Conformance . 41 5 Testing for compliance with technical requirements . 41 5.1 Environmental conditions for testing . 41 5.2 Interpretation of the measurement results . 41 5.3 Essential radio test suites . 43 5.3.1 Operating band unwanted emissions . 43 5.3.1.1 Initial conditions . 43 5.3.1.2 Procedure . 44 5.3.1.3 Test requirement . 44 5.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 44 5.3.2.1 Initial conditions . 44 5.3.2.2 Procedure . 45 5.3.2.3 Test requirement . 45 5.3.3 Transmitter spurious emissions . 45 5.3.3.1 Initial conditions . 45 5.3.3.2 Procedure . 46 5.3.3.3 Test requirement . 46 5.3.4 Base station maximum output power . 46 5.3.4.1 Initial conditions . 46 5.3.4.2 Procedure . 46 5.3.4.3 Test requirement . 46 5.3.5 Transmit intermodulation . 47 5.3.5.1 Initial conditions . 47 5.3.5.2 Procedure . 47 5.3.5.2.1 General minimum requirement test procedure . 47 5.3.5.2.2 Additional minimum requirement (BC1 and BC2) test procedure . 48 5.3.5.2.3 Additional minimum requirement (BC3) test procedure . 49 5.3.5.3 Test requirement . 49 5.3.6 Receiver spurious emissions . 49 5.3.6.1 Initial conditions . 49 5.3.6.2 Procedure . 50 5.3.6.3 Test requirement . 50 5.3.7 In-band blocking . 50 5.3.7.1 Initial conditions . 50 SIST EN 301 908-18 V7.1.2:2014



ETSI ETSI EN 301 908-18 V7.1.2 (2014-07)55.3.7.2 Procedure . 50 5.3.7.2.1 Procedure for general blocking . 50 5.3.7.2.2 Procedure for additional BC3 blocking requirement . 51 5.3.7.3 Test requirement . 51 5.3.8 Out-of-band blocking . 51 5.3.8.1 Initial conditions . 51 5.3.8.2 Procedure . 52 5.3.8.3 Test requirement . 52 5.3.9 Receiver intermodulation characteristics . 52 5.3.9.1 Initial conditions . 52 5.3.9.2 Procedure . 53 5.3.9.2.1 Procedure for general and narrowband intermodulation . 53 5.3.9.2.2 Procedure for additional narrowband intermodulation for GSM/EDGE . 53 5.3.9.3 Test requirement . 53 5.3.10 Narrowband blocking . 53 5.3.10.1 Initial conditions . 53 5.3.10.2 Procedure . 54 5.3.10.2.1 Procedure for narrowband blocking . 54 5.3.10.2.2 Procedure for additional narrowband blocking for GSM/EDGE . 54 5.3.10.2.3 Procedure for GSM/EDGE AM suppression . 54 5.3.10.3 Test requirement . 54 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 55 Annex B (normative): Base Station configurations . 57 B.1 Reception with multiple receiver antenna connectors and receiver diversity . 57 B.2 Duplexers . 57 B.3 Power supply options . 57 B.4 Ancillary RF amplifiers . 57 B.5 BS using antenna arrays . 58 B.5.1 Receiver tests . 58 B.5.2 Transmitter tests . 59 B.6 Transmission with multiple transmitter antenna connectors . 59 B.7 BS with integrated Iuant BS modem . 59 Annex C (informative): Environmental profile specification . 60 Annex D (informative): Bibliography . 61 History . 62
SIST EN 301 908-18 V7.1.2:2014



ETSI ETSI EN 301 908-18 V7.1.2 (2014-07)6fntellectual=mroéerty=oights=IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. coreword=This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A. The present document is part 18 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.7].
National transposition dates Date of adoption of this EN: 30 June 2014 Date of latest announcement of this EN (doa): 30 September 2014 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 March 2015 Date of withdrawal of any conflicting National Standard (dow): 31 March 2016
àodal=verbs=terminology=In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. fntroduction=The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-18 V7.1.2:2014



ETSI ETSI EN 301 908-18 V7.1.2 (2014-07)7k=écoée=The present document applies to the following radio equipment type: 1) Multi-Standard Radio capable Base stations (E-UTRA, UTRA, GSM/EDGE). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: Base station operating bands Band designation and Band Category Direction of transmission MSR Base Station operating bands k=b_Ckc=qransmit==l=kkà=àez=to=l=kqà=àez=oeceive==k=slà=àez=to=k=srà=àez=m=b_Clc=qran
...

ETSI EN 301 908-18 V7.1.2 (2014-07)






HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 18: E-UTRA, UTRA and GSM/EDGE
Multi-Standard Radio (MSR) Base Station (BS)

---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-18 V7.1.2 (2014-07)



Reference
REN/MSG-TFES-011-18a
Keywords
3G, 3GPP, cellular, digital, EDGE, E-UTRA,
GSM, IMT, IMT-Advanced, IMT-2000, LTE,
mobile, MSR, radio, regulation, UMTS, UTRA,
WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-18 V7.1.2 (2014-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 11
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Environmental profile . 13
4.2 Conformance requirements . 13
4.2.1 Introduction. 13
4.2.2 Operating band unwanted emissions . 15
4.2.2.1 Definition . 15
4.2.2.2 Limits . 16
4.2.2.2.1 Limits for Band Categories 1 and 3 . 16
4.2.2.2.2 Limits for Band Category 2 . 20
4.2.2.2.3 Limits for GSM/EDGE single-RAT operation . 25
4.2.2.2.4 Limits for protection of DTT . 25
4.2.2.2.5 Limits for co-existence with services in adjacent frequency bands . 25
4.2.2.3 Conformance . 26
4.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 26
4.2.3.1 Definition . 26
4.2.3.2 Limits . 26
4.2.3.2.1 E-UTRA limits . 26
4.2.3.2.2 UTRA FDD limits . 26
4.2.3.2.3 UTRA TDD limits . 26
4.2.3.2.4 Cumulative ACLR requirement in non-contiguous spectrum . 27
4.2.3.3 Conformance . 28
4.2.4 Transmitter spurious emis sions . 28
4.2.4.1 Limits . 28
4.2.4.1.1 Spurious emissions . 28
4.2.4.1.2 Additional spurious emissions requirement for BC2 . 28
4.2.4.1.3 Co-existence with other systems . 29
4.2.4.1.4 Protection of the BS receiver of own or different BS . 30
4.2.4.2 Conformance . 31
4.2.5 Base station maximum output power . 31
4.2.5.1 Definition . 31
4.2.5.2 Limits . 31
4.2.5.3 Conformance . 31
4.2.6 Transmit intermodulation . 31
4.2.6.1 Definition . 31
4.2.6.2 Limits . 32
4.2.6.2.1 General limits . 32
4.2.6.2.2 Additional limits (BC1 and BC2) . 32
4.2.6.2.3 Additional limits (BC3) . 33
4.2.6.3 Conformance . 33
4.2.7 Receiver spurious emissions . 33
4.2.7.1 Definition . 33
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-18 V7.1.2 (2014-07)
4.2.7.2 Limits . 34
4.2.7.2.1 General limits . 34
4.2.7.2.2 Additional limits for BC2 . 34
4.2.7.3 Conformance . 34
4.2.8 In-band blocking . 34
4.2.8.1 Definition . 34
4.2.8.2 Limits . 35
4.2.8.2.1 General limits . 35
4.2.8.2.2 Additional BC3 blocking limits . 36
4.2.8.3 Conformance . 36
4.2.9 Out-of-band blocking . 36
4.2.9.1 Definition . 36
4.2.9.2 Limits . 36
4.2.9.3 Conformance . 37
4.2.10 Receiver intermodulation characteristics . 37
4.2.10.1 Definition . 37
4.2.10.2 Limits . 37
4.2.10.2.1 General intermodulation limits . 37
4.2.10.2.2 General narrowband intermodulation limits . 38
4.2.10.2.3 Additional narrowband intermodulation limits for GSM/EDGE . 40
4.2.10.3 Conformance . 40
4.2.11 Narrowband blocking . 40
4.2.11.1 Definition . 40
4.2.11.2 Limits . 40
4.2.11.2.1 General limits . 40
4.2.11.2.2 Additional limits for GSM/EDGE . 41
4.2.11.2.3 GSM/EDGE limits for AM suppression . 41
4.2.11.3 Conformance . 41
5 Testing for compliance with technical requirements . 41
5.1 Environmental conditions for testing . 41
5.2 Interpretation of the measurement results . 41
5.3 Essential radio test suites . 43
5.3.1 Operating band unwanted emissions . 43
5.3.1.1 Initial conditions . 43
5.3.1.2 Procedure . 44
5.3.1.3 Test requirement . 44
5.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 44
5.3.2.1 Initial conditions . 44
5.3.2.2 Procedure . 45
5.3.2.3 Test requirement . 45
5.3.3 Transmitter spurious emis sions . 45
5.3.3.1 Initial conditions . 45
5.3.3.2 Procedure . 46
5.3.3.3 Test requirement . 46
5.3.4 Base station maximum output power . 46
5.3.4.1 Initial conditions . 46
5.3.4.2 Procedure . 46
5.3.4.3 Test requirement . 46
5.3.5 Transmit intermodulation . 47
5.3.5.1 Initial conditions . 47
5.3.5.2 Procedure . 47
5.3.5.2.1 General minimum requirement test procedure . 47
5.3.5.2.2 Additional minimum requirement (BC1 and BC2) test procedure . 48
5.3.5.2.3 Additional minimum requirement (BC3) test procedure . 49
5.3.5.3 Test requirement . 49
5.3.6 Receiver spurious emissions . 49
5.3.6.1 Initial conditions . 49
5.3.6.2 Procedure . 50
5.3.6.3 Test requirement . 50
5.3.7 In-band blocking . 50
5.3.7.1 Initial conditions . 50
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-18 V7.1.2 (2014-07)
5.3.7.2 Procedure . 50
5.3.7.2.1 Procedure for general blocking . 50
5.3.7.2.2 Procedure for additional BC3 blocking requirement . 51
5.3.7.3 Test requirement . 51
5.3.8 Out-of-band blocking . 51
5.3.8.1 Initial conditions . 51
5.3.8.2 Procedure . 52
5.3.8.3 Test requirement . 52
5.3.9 Receiver intermodulation characteristics . 52
5.3.9.1 Initial conditions . 52
5.3.9.2 Procedure . 53
5.3.9.2.1 Procedure for general and narrowband intermodulation . 53
5.3.9.2.2 Procedure for additional narrowband intermodulation for GSM/EDGE . 53
5.3.9.3 Test requirement . 53
5.3.10 Narrowband blocking . 53
5.3.10.1 Initial conditions . 53
5.3.10.2 Procedure . 54
5.3.10.2.1 Procedure for narrowband blocking . 54
5.3.10.2.2 Procedure for additional narrowband blocking for GSM/EDGE . 54
5.3.10.2.3 Procedure for GSM/EDGE AM suppression . 54
5.3.10.3 Test requirement . 54
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 55
Annex B (normative): Base Station configurations . 57
B.1 Reception with multiple receiver antenna connectors and receiver diversity . 57
B.2 Duplexers . 57
B.3 Power supply options . 57
B.4 Ancillary RF amplifiers . 57
B.5 BS using antenna arrays . 58
B.5.1 Receiver tests . 58
B.5.2 Transmitter tests . 59
B.6 Transmission with multiple transmitter antenna connectors . 59
B.7 BS with integrated Iuant BS modem . 59
Annex C (informative): Environmental profile specification . 60
Annex D (informative): Bibliography . 61
History . 62

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-18 V7.1.2 (2014-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 18 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.7].

National transposition dates
Date of adoption of this EN: 30 June 2014
Date of latest announcement of this EN (doa): 30 September 2014
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2015
Date of withdrawal of any conflicting National Standard (dow): 31 March 2016

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-18 V7.1.2 (2014-07)
1 Scope
The present document applies to the following radio equipment type:
1) Multi-Standard Radio capable Base stations (E-UTRA, UTRA, GSM/EDGE).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: Base station operating bands
Band Direction of transmission MSR Base Station operating bands
designation and
Band Category
1 (BC1) Transmit 2 110 MHz to 2 170 MHz
Receive 1 920 MHz to 1 980 MHz
3 (BC2) Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
7 (BC1) Transmit 2 620 MHz to 2 690 MHz
Receive 2 500 MHz to 2 570 MHz
8 (BC2) Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
20 (BC1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.