SIST EN ISO/IEC 15426-2:2006

Information technology - Automatic identification and data capture techniques - Bar code verifier conformance specification - Part 2: Two-dimensional symbols (ISO/IEC 15426-2:2005)

This part of ISO/IEC 15426 defines test methods and minimum accuracy criteria applicable to verifiers using the methodologies of ISO/IEC 15415 for multi-row bar code symbols and two-dimensional matrix symbologies, and specifies reference calibration standards against which these should be tested. This part of ISO/IEC 15426 provides for testing of representative samples of the equipment.

Informationstechnik - Automatische Identifikation und Datenerfassungsverfahren - Prüfanforderungen für Strichcodeprüfgeräte - Teil 2: Zweidimensionale Symbologien (ISO/IEC 15426-2:2005)

Technologies de l'information - Techniques d'identification automatique et de capture de données - Spécifications de conformité des vérificateurs de codes a barres - Partie 2: Symboles bidimensionnels (ISO/IEC 15426-2:2005)

Informacijska tehnologija – Tehnike za samodejno razpoznavanje in zajem podatkov – Specifikacija o skladnosti za verifikatorje črtnih kod – 2. del: Dvodimenzionalni simboli (ISO/IEC 15426-2:2005)

Ta del standarda ISO/IEC 15426 določa preskusne metode in kriterije minimalne natančnosti za preverjanje z uporabo metodologije ISO/IEC 15415 za simbole črtne kode v več vrsticah in dvodimenzionalne simbološke matrike ter določa standarde kalibracije referenc, s katerimi bi morali biti preskušeni. Ta del standarda ISO/IEC 15426 je namenjen preskušanju reprezentativnih vzorcev opreme.
OPOMBA: ISO/IEC 15426-1 velja tudi za verifikatorje linearnih simbolov črtnih kod.

General Information

• Status: Published
• Publication Date: 31-May-2006
• ICS: 35.040.50 - Automatic identification and data capture techniques
• Technical Committee: ITC - Information technology
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jun-2006
• Due Date: 01-Jun-2006
• Completion Date: 01-Jun-2006
• Ref Project: EN ISO/IEC 15426-2:2006 - Information technology - Automatic identification and data capture techniques - Bar code verifier conformance specification - Part 2: Two-dimensional symbols (ISO/IEC 15426-2:2005)

Relations

• Corrected By: SIST EN ISO/IEC 15426-2:2006/AC:2013 - Information technology - Automatic identification and data capture techniques - Bar code verifier conformance specification - Part 2: Two-dimensional symbols - Technical Corrigendum 1 (ISO/IEC 15426-2:2005/Cor 1:2008)
• Effective Date: 01-Mar-2013

Standards Content (Sample)

SLOVENSKI SIST EN ISO/IEC 15426-2:2006

STANDARD
junij 2006
Informacijska tehnologija – Tehnike za samodejno razpoznavanje in zajem
podatkov – Specifikacija o skladnosti za verifikatorje črtnih kod – 2. del:
Dvodimenzionalni simboli (ISO/IEC 15426-2:2005)
Information technology – Automatic identification and data capture techniques –
Bar code verifier conformance specification – Part 2: Two-dimensional symbols
(ISO/IEC 15426-2:2005)
ICS 35.040 Referenčna številka
SIST EN ISO/IEC 15426-2:2006(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
FINAL DRAFT
prEN ISO/IEC 15426-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2005
ICS 35.040
English version
Information technology - Automatic identification and data
capture techniques - Bar code verifier conformance specification
- Part 2: Two-dimensional symbols (ISO/IEC 15426-2:2005)
Technologies de l'information - Techniques d'identification
automatique et de capture de données - Spécifications de
conformité des vérificateurs de codes à barres - Partie 2:
Symboles bidimensionnels (ISO/IEC 15426-2:2005)
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 225.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO/IEC 15426-2:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

prEN ISO/IEC 15426-2:2005 (E)






Foreword



The text of ISO/IEC 15426-2:2005 has been prepared by Technical Committee ISO/IEC/JTC 1
"Information technology” of the International Organization for Standardization (ISO) and has
been taken over as prEN ISO/IEC 15426-2:2005 by Technical Committee CEN/TC 225 "AIDC
technologies", the secretariat of which is held by NEN.

This document is currently submitted to the Unique Acceptance Procedure.



Endorsement notice

The text of ISO/IEC 15426-2:2005 has been approved by CEN as prEN ISO/IEC 15426-2:2005
without any modifications.

2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO/IEC
STANDARD 15426-2
First edition
2005-03-15


Information technology — Automatic
identification and data capture
techniques — Bar code verifier
conformance specification —
Part 2:
Two-dimensional symbols
Technologies de l'information — Techniques d'identification
automatique et de capture de données — Spécifications de conformité
des vérificateurs de codes à barres —
Partie 2: Symboles bidimensionnels





Reference number
ISO/IEC 15426-2:2005(E)
©
ISO/IEC 2005

---------------------- Page: 4 ----------------------

ISO/IEC 15426-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO/IEC 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2005 – All rights reserved

---------------------- Page: 5 ----------------------

ISO/IEC 15426-2:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Conformance . 1
3 Normative references . 2
4 Terms and definitions. 2
5 Symbols . 2
6 Functional requirements . 2
6.1 General requirements . 2
6.2 Reflectance calibration. 3
6.3 Mandatory functions. 3
6.3.1 Verifiers for multi-row bar code symbols. 3
6.3.2 Verifiers for two-dimensional matrix symbols. 3
6.4 Optional functions . 4
7 General constructional and operational requirements . 4
7.1 Installation, operation and maintenance . 4
7.2 Power supply. 4
7.3 Temperature . 4
7.3.1 Operating temperature range. 4
7.3.2 Storage temperature range . 4
7.4 Humidity. 4
7.5 Ambient light immunity . 5
8 Test requirements . 5
8.1 Test methods. 5
8.1.1 Selection of equipment for testing. 5
8.1.2 Scanning parameters. 5
8.1.3 Test measurements . 5
8.2 Test environment . 5
8.3 Primary reference test symbols . 5
8.4 Test report. 6
9 Certification and labelling . 7
10 Equipment specification. 7
Annex A (normative) Primary reference test symbols . 8
Annex B (normative) Verification requirements for primary reference test symbols . 13

© ISO/IEC 2005 – All rights reserved iii

---------------------- Page: 6 ----------------------

ISO/IEC 15426-2:2005(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 15426-2 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 31, Automatic identification and data capture techniques.
ISO/IEC 15426 consists of the following parts, under the general title Information technology — Automatic
identification and data capture techniques — Bar code verifier conformance specification:
— Part 1: Linear symbols
— Part 2: Two-dimensional symbols
iv © ISO/IEC 2005 – All rights reserved

---------------------- Page: 7 ----------------------

ISO/IEC 15426-2:2005(E)
Introduction
The technology of bar coding is based on the recognition of patterns encoded, in bars and spaces or in a
matrix of modules of defined dimensions, according to rules defining the translation of characters into such
patterns, known as the symbology specification. Symbology specifications may be categorised into linear
symbols, on the one hand, and two-dimensional symbols on the other; the latter may in turn be sub-divided
into «multi-row bar codes» sometimes referred to as «stacked bar codes», and «two-dimensional matrix
codes».
Multi-row bar codes are constructed graphically as a series of rows of symbol characters, representing data
and overhead components, placed in a defined vertical arrangement to form a (normally) rectangular symbol,
which contains a single data message. Each row of the symbol has the characteristics of a linear bar code
symbol and may be read by linear symbol scanning techniques.
Two-dimensional matrix symbols are usually rectangular arrangements of modules placed at the intersections
of a grid of two (sometimes more) axes; the coordinates of each module need to be known in order to
determine its significance, and the symbol must therefore be analysed two-dimensionally before it can be
decoded.
Unless the context requires otherwise, the term «symbol» in this part of ISO/IEC 15426 may refer to either
type of symbology.
The symbol, as a machine-readable data carrier, must be produced in such a way as to be reliably decoded at
the point of use, if it is to fulfil its basic objective. Standard methodologies have been developed for measuring
and assessing the quality of symbols for process control and quality assurance purposes during symbol
production as well as afterwards.
Manufacturers of bar code equipment, the producers of bar code symbols and the users of bar code
technology require publicly available standard conformance specifications for measuring equipment applying
these methodologies, to ensure the accuracy and consistency of performance of this equipment.
This part of ISO/IEC 15426 is intended to be similar in technical content (mutatis mutandis) to the linear bar
code verifier conformance standard, ISO/IEC 15426-1, on which it has been based. It should be read in
conjunction with the symbology specification applicable to the bar code symbol being tested, which provides
symbology-specific detail necessary for its application.

© ISO/IEC 2005 – All rights reserved v

---------------------- Page: 8 ----------------------

INTERNATIONAL STANDARD ISO/IEC 15426-2:2005(E)

Information technology — Automatic identification and data
capture techniques — Bar code verifier conformance
specification —
Part 2:
Two-dimensional symbols
1 Scope
This part of ISO/IEC 15426 defines test methods and minimum accuracy criteria applicable to verifiers using
the methodologies of ISO/IEC 15415 for multi-row bar code symbols and two-dimensional matrix symbologies,
and specifies reference calibration standards against which these should be tested. This part of
ISO/IEC 15426 provides for testing of representative samples of the equipment.
NOTE ISO/IEC 15426-1 applies to verifiers for linear bar code symbols.
2 Conformance
The instrument shall be considered to conform with this part of ISO/IEC 15426 if it performs the functions
defined in 6.3 and if the results of measurements of primary reference test symbols carried out in accordance
with Clause 8 demonstrate that the arithmetic means of the ten measurements (for multi-row bar code
symbols) or five measurements (for two-dimensional matrix symbols) of individual reported parameters are
within the tolerances shown in Table 1 below.
Table 1 — Tolerances for measured parameter values
Parameter Symbology type Tolerance
R and/or R Both
± 5 % reflectance
max s
R and/or R
Both ± 3 % reflectance
min b
UEC Both
± 0,0
Decodability Multi-row
± 0,08
Defects Multi-row ± 0,08
Codeword Yield Multi-row ± 0,08
Grid Nonuniformity Matrix
± 0,06
Modulation Matrix ± 0,08 of the value
measured for the
reduced dark widow on a
calibrated test symbol
card
Fixed Pattern Damage Matrix Within calibrated grade
boundaries

NOTE The tolerances in Table 1 are additional to any tolerances stated by the supplier of the primary reference test
symbols.
© ISO/IEC 2005 – All rights reserved 1

---------------------- Page: 9 ----------------------

ISO/IEC 15426-2:2005(E)
3 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2859-1:1999, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
ISO 9001:2000, Quality management systems — Requirements
ISO/IEC 15415, Information technology — Automatic identification and data capture techniques — Bar code
print quality test specification — Two-dimensional symbols
ISO/IEC 15416, Information technology — Automatic identification and data capture techniques — Bar code
print quality test specification — Linear symbols
ISO/IEC 15438, Information technology — Automatic identification and data capture techniques — Bar code
symbology specifications — PDF417
ISO/IEC 16022, Information technology — International symbology specification — Data Matrix
ISO/IEC 19762 (all parts), Information technology — Automatic identification and data capture (AIDC)
techniques — Harmonized vocabulary
ISO/IEC 18004, Information technology —Automatic identification and data capture techniques — Bar code
symbology — QR Code
4 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/IEC 15415, ISO/IEC 19762 (all
parts) and the following apply.
4.1
primary reference test symbol
bar code symbol intended for the testing of the accuracy of bar code verifiers and manufactured to close
tolerances, of at least ten times the precision listed in Table 1, by methods traceable to national standards
5 Symbols
R Bar Reflectance, as defined in ISO/IEC 15416
b
R Maximum reflectance, as defined in ISO/IEC 15416
max
R Minimum reflectance, as defined in ISO/IEC 15416
min
R Space Reflectance, as defined in ISO/IEC 15416
s
6 Functional requirements
6.1 General requirements
The general requirement of a two-dimensional symbol verifier is that it shall provide assessments of the
quality of a bar code symbol which are accurate and consistent, both in relation to measurements of a specific
2 © ISO/IEC 2005 – All rights reserved

---------------------- Page: 10 ----------------------

ISO/IEC 15426-2:2005(E)
symbol made with the same instrument over a period of time and in relation to measurements of a specific
symbol made by different instruments. Such consistency is essential to enable valid comparisons to be made
of assessments of a symbol verified at two different times or on two different instruments.
6.2 Reflectance calibration
Verifiers shall have means of calibration and adjustment where necessary of reflectance values against
reference reflectance calibration samples. Two calibration points should be used, one as near the high
reflectance end of the range and the other as near the low reflectance end of the range as possible.
ISO/IEC 15415 defines the reference reflectance material against which these samples shall be calibrated.
6.3 Mandatory functions
6.3.1 Verifiers for multi-row bar code symbols
A verifier for multi-row bar code symbols applying the methodology defined in ISO/IEC 15415 shall be capable
of:
 collecting reflectance measurements from points along multiple scan paths across a bar code symbol;
 establishing scan reflectance profiles from these measurements;
 analysing the scan reflectance profiles;
 reporting individual scan reflectance profile parameter grades and profile grades;
 reporting the Codeword Yield value and grade;
 reporting the Unused Error Correction value and grade;
 determining and reporting an overall symbol grade;
 reporting the decoded data.
6.3.2 Verifiers for two-dimensional matrix symbols
A verifier for two-dimensional matrix symbols applying the methodology defined in ISO/IEC 15415 shall be
capable of:
 collecting reflectance measurements from a sample area framing the test symbol and its quiet zones,
extending for certain symbol sizes 20X beyond the quiet zones (see Clause 10);
 establishing a reference grey-scale image a
...