iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN 10379:2024

(Main)

Steel sheet piles - Test methods

Steel sheet piles - Test methods

This document specifies the requirement for testing of special properties of hot-rolled steel sheet piles.

Spundbohlen aus Stahl - Prüfverfahren

Dieses Dokument legt die Anforderungen an spezielle Prüfverfahren für warmgewalzte Spundbohlen fest.

Palplanches en acier - Méthodes d’essais

Le présent document spécifie les prescriptions relatives aux essais des propriétés spéciales des palplanches en acier laminées à chaud.

Jeklene zagatnice – preskusne metode

General Information

Status
Not Published
Public Enquiry End Date
28-May-2024
ICS
77.140.50 - Flat steel products and semi-products
77.140.70 - Steel profiles
Technical Committee
IFEK - Ferrous metals
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
25-Mar-2024
Due Date
12-Aug-2024
Completion Date
30-May-2024
Ref Project
prEN 10379 - Steel sheet piles - Test methods

Buy Standard

prEN 10379:2024prEN 10379:2024
PreviousNext
Draft
prEN 10379:2024
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 10379:2024
01-maj-2024
Jeklena obešala - Preskusne metode
Steel sheet piles - Test methods
Spundbohlen aus Stahl - Prüfverfahren
Palplanches en acier - Méthodes d’essais
Ta slovenski standard je istoveten z: prEN 10379
ICS:
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
77.140.70 Jekleni profili Steel profiles
oSIST prEN 10379:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 10379:2024

---------------------- Page: 2 ----------------------
oSIST prEN 10379:2024


DRAFT
EUROPEAN STANDARD
prEN 10379
NORME EUROPÉENNE

EUROPÄISCHE NORM

March 2024
ICS 77.140.50
English Version

Steel sheet piles - Test methods
 Spundbohlen aus Stahl - Prüfverfahren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 3.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10379:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 10379:2024
prEN 10379:2024 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 General requirements . 4
5 Test of the resistance of crimped points of U-shaped sheet piles . 4
5.1 General. 4
5.2 Test specimen . 5
5.3 Testing and evaluation. 7
6 Test of the interlock resistance of straight web sheet piles . 8
6.1 General. 8
6.2 Test specimen . 8
6.3 Testing and evaluation. 9
7 Test of interlock performance of U-shaped and Z-shaped sheet piles . 10
7.1 General.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 10163-1:2005/AC:2007(Corrigendum)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
EN 10163-1:2004/AC:2007

CMC - Modification to Clause 2

  • Corrigendum
    2 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10163-3:2005(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
EN 10163-3:2004

This Part 3 in addition to Part 1 of this European Standard specifies the delivery requirements for surface condition of sections to which the European Standards mentioned in clause 2 apply and applies to all surfaces excluding edges.
NOTE   In this European Standard section toes (see EN 10055) are considered as part of the surfaces of a section.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10163-2:2005(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
EN 10163-2:2004

This Part 2 in addition to Part 1 of this European Standard specifies the delivery requirements which apply to the surface condition of hot-rolled plates and surface condition of the faces of wide flats with thicknesses of 3 mm = t = 400 mm.
NOTE   For plates with a thickness > 400 mm special agreements should be made at the time of the order.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10163-1:2005(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
EN 10163-1:2004

1.1   This European Standard specifies the general requirements for the surface condition of hot-rolled steel plates, wide flats and sections. It covers the requirements on the type, the permissible depth and the permissible size of the surface area affected by:
3 discontinuities (imperfections ant defects) and
3 repairs by grinding and/or welding.
1.2   This European Standard shall be applied so far as no other requirements for the surface condition exist in the appropriate material or product standard. The requirements laid down in the appropriate material or product standard shall always prevail.
1.3   This Part 1 of this European Standard covers the general delivery requirements for the surface condition of hot-rolled steel products such as:
3 plates and wide flats, see Part 2;
3 sections, see Part 3;

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10163-1:2005/AC:2007(Corrigendum)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
EN 10163-1:2004/AC:2007

CMC - Modification to Clause 2

  • Corrigendum
    2 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10163-3:2005(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
EN 10163-3:2004

This Part 3 in addition to Part 1 of this European Standard specifies the delivery requirements for surface condition of sections to which the European Standards mentioned in clause 2 apply and applies to all surfaces excluding edges.
NOTE   In this European Standard section toes (see EN 10055) are considered as part of the surfaces of a section.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10163-2:2005(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
EN 10163-2:2004

This Part 2 in addition to Part 1 of this European Standard specifies the delivery requirements which apply to the surface condition of hot-rolled plates and surface condition of the faces of wide flats with thicknesses of 3 mm = t = 400 mm.
NOTE   For plates with a thickness > 400 mm special agreements should be made at the time of the order.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10163-1:2005(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
EN 10163-1:2004

1.1   This European Standard specifies the general requirements for the surface condition of hot-rolled steel plates, wide flats and sections. It covers the requirements on the type, the permissible depth and the permissible size of the surface area affected by:
3 discontinuities (imperfections ant defects) and
3 repairs by grinding and/or welding.
1.2   This European Standard shall be applied so far as no other requirements for the surface condition exist in the appropriate material or product standard. The requirements laid down in the appropriate material or product standard shall always prevail.
1.3   This Part 1 of this European Standard covers the general delivery requirements for the surface condition of hot-rolled steel products such as:
3 plates and wide flats, see Part 2;
3 sections, see Part 3;

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62841-4-6:2024/A11:2024(Amendment)
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 4-6: Particular requirements for garden blowers, garden vacuums and garden blower/vacuums
EN IEC 62841-4-6:2024/A11:2024

2021-05-14: This prAA includes CMs to EN IEC (PR=72116), both PRs to be circulated simultaneously
D164/C043: DOW=DOR+48 months

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50726-1:2024(Main)
Emergency and danger systems - Part 1: Emergency and danger response systems (EDRS) - Basic requirements, duties, responsibilities and activities
EN 50726-1:2024

This document applies to the planning, installation, commissioning, operation and maintenance of an emergency and danger response system. An emergency and danger response system is part of an overall solution for dealing with specific events such as emergencies or crises.
This document
-   specifies:
-   technical processes and responsibilities for supporting all procedures from the registration of an event (emergency, danger) up to its final processing;
-   the technical risk management including the definition of safety/security goals and the workflow organization as well as the necessary specifications regarding a technical risk management file;
-   associated duties, responsibilities and activities as parts of an integrated overall risk management process to achieve the safety and security goals, effectiveness and efficiency as well as data and system safety/security;
-   three different grades of safety/security, with the respective product functionalities required to achieve them;
-   the basic requirements for emergency and danger response systems (EDRS) in public buildings such as education facilities (e.g. schools, universities), government facilities, kindergartens and similar facilities;
-   the responsibilities under applicable national law about Safety and Health at Work Laws and thus particularly addresses the responsibility of employers;
-   describes:
-   the process of establishing, maintaining and updating a risk management file in which, inter alia, the technical risks are listed and evaluated and the residual technical risks are defined, resulting in the grade and structure of the EDRS;
-   is intended to support the implementation of:
-   National legal and other provisions (e.g. Act on Equal Opportunities for People with Disabilities, Safety and Health at Work Laws, education laws);
-   gives relevant guidance on:
-   the organizational risk management;
-   does not replace the specifications of standards to the following systems:
-   fire safety systems including, but not limited to, fire detection and fire alarm systems, fixed firefighting systems, smoke and heat control systems,
-   security systems including, but not limited to, intrusion and hold-up alarm systems, electronic access control systems, external perimeter security systems and video surveillance systems,
-   applicable national standards on call systems.
All such systems can, however, be integrated into an emergency and danger response system (EDRS), taking into account the relevant provisions made in the respective standards for such products and systems.
Other products and systems from the entire field of standardization, such as alarm systems, danger warning and danger alarm systems, escape routing systems, public address systems used to respond to a danger, can also be used in or integrated into an emergency and danger response system if the relevant requirements of the standards for such products or systems are met.
This document does not specify any risk levels, in particular no acceptable residual risks. Technical risk management and organizational risk management are equal parts of the overall risk management.
This document is also applicable to non-public buildings with a similar risk and requirement for protection.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day