SIST EN IEC 62149-12:2023
(Main)Fibre optic active components and devices - Performance standards - Part 12: Distributed feedback laser diode device for analogue radio over fibre systems (IEC 62149-12:2023)
Fibre optic active components and devices - Performance standards - Part 12: Distributed feedback laser diode device for analogue radio over fibre systems (IEC 62149-12:2023)
IEC 62149-12:2023 This part of IEC 62149 defines performance specifications for distributed feedback laser diode (DFB-LD) devices used in analogue radio over fibre (RoF) systems. It defines product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a “once-off” basis to prove a product’s ability to satisfy the performance requirements.
Aktive Lichtwellenleiterbauelemente und -geräte - Betriebsverhaltensnormen - Teil 12: Laserdiodenbauelemente mit verteilter Rückkopplung für analoge Funksignalübertragung über Glasfasersysteme (IEC 62149-12:2023)
Composants et dispositifs actifs fibroniques – Normes de performances – Partie 12: Dispositif à diode laser à rétroaction répartie pour systèmes radio analogique sur fibre (IEC 62149-12:2023)
IEC 62149-12:2023 définit les spécifications de performances des dispositifs à diode laser à rétroaction répartie (DFB-LD) utilisés dans les systèmes de type radio analogique sur fibre (RoF). Elle définit les exigences de performances du produit, accompagnées d’une série d’essais et de mesures comportant des conditions, des sévérités et des critères d’acceptation/de rejet clairement définis. Les essais sont destinés à être effectués en une seule et unique fois, afin de démontrer la capacité d'un produit donné à satisfaire aux exigences de performances.
Optične aktivne komponente in naprave - Izvedbeni standardi - 12. del: Naprava z lasersko diodo na porazdeljeno povratno vezavo za analogne radijske signale po sistemih optičnih vlaken (IEC 62149-12:2023)
Standard IEC 62149-12:2023 Ta del standarda IEC 62149 določa specifikacije delovanja naprav z distribucijsko povratno lasersko diodo (DFB-LD), ki se uporabljajo v analognih sistemih za prenos radijskih signalov po optičnih kablih (RoF). Določa zahteve glede zmogljivosti za izdelek skupaj z naborom preskusov in meritev z jasno določenimi pogoji, stopnjami zahtevnosti in merili za uspešno/neuspešno opravljen preskus. Preskusi so namenjeni enkratnemu izvajanju, z njimi pa se dokaže, ali lahko izdelek izpolnjuje zahteve glede zmogljivosti.
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 62149-12:2023
01-maj-2023
Optične aktivne komponente in naprave - Izvedbeni standardi - 12. del: Naprava z
lasersko diodo na porazdeljeno povratno vezavo za analogne radijske signale po
sistemih optičnih vlaken (IEC 62149-12:2023)
Fibre optic active components and devices - Performance standards - Part 12:
Distributed feedback laser diode device for analogue radio over fibre systems (IEC
62149-12:2023)
Aktive Lichtwellenleiterbauelemente und -geräte - Betriebsverhaltensnormen - Teil 12:
Laserdiodenbauelemente mit verteilter Rückkopplung für analoge
Funksignalübertragung über Glasfasersysteme (IEC 62149-12:2023)
Composants et dispositifs actifs fibroniques – Normes de performances – Partie 12:
Dispositif à diode laser à rétroaction répartie pour systèmes radio analogique sur fibre
(IEC 62149-12:2023)
Ta slovenski standard je istoveten z: EN IEC 62149-12:2023
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 62149-12:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 62149-12:2023
---------------------- Page: 2 ----------------------
SIST EN IEC 62149-12:2023
EUROPEAN STANDARD EN IEC 62149-12
NORME EUROPÉENNE
EUROPÄISCHE NORM March 2023
ICS 33.180.20
English Version
Fibre optic active components and devices - Performance
standards - Part 12: Distributed feedback laser diode device for
analogue radio over fibre systems
(IEC 62149-12:2023)
Composants et dispositifs actifs fibroniques - Normes de Aktive Lichtwellenleiterbauelemente und -geräte -
performances - Partie 12: Dispositif à diode laser à Betriebsverhaltensnormen - Teil 12:
rétroaction répartie pour systèmes radio analogiques sur Laserdiodenbauelemente mit verteilter Rückkopplung für
fibre analoge Funksignalübertragung über LWL-Systeme
(IEC 62149-12:2023) (IEC 62149-12:2023)
This European Standard was approved by CENELEC on 2023-03-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62149-12:2023 E
---------------------- Page: 3 ----------------------
SIST EN IEC 62149-12:2023
EN IEC 62149-12:2023 (E)
European foreword
The text of document 86C/1808/CDV, future edition 1 of IEC 62149-12, prepared by SC 86C "Fibre
optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 62149-12:2023.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-12-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-03-17
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62149-12:2023 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 62007-1 NOTE Approved as EN 62007-1
IEC 62149-2 NOTE Approved as EN 62149-2
IEC 62149-7 NOTE Approved as EN 62149-7
IEC 62149-8 NOTE Approved as EN 62149-8
IEC 62149-10 NOTE Approved as EN IEC 62149-10
2
---------------------- Page: 4 ----------------------
SIST EN IEC 62149-12:2023
EN IEC 62149-12:2023 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60749-6 - Semiconductor devices - Mechanical and EN 60749-6 -
climatic test methods - Part 6: Storage at high
temperature
IEC 60749-7 - Semiconductor devices - Mechanical and EN 60749-7 -
climatic test methods - Part 7: Internal
moisture content measurement and the
analysis of other residual gases
IEC 60749-10 - Semiconductor devices - Mechanical and EN IEC 60749-10 -
climatic test methods - Part 10: Mechanical
shock - device and subassembly
IEC 60749-11 - Semiconductor devices - Mechanical and EN 60749-11 -
climatic test methods - Part 11: Rapid change
of temperature - Two-fluid-bath method
IEC 60749-12 - Semiconductor devices - Mechanical and EN IEC 60749-12 -
climatic test methods - Part 12: Vibration,
variable frequency
IEC 60749-25 - Semiconductor devices - Mechanical and EN 60749-25 -
climatic test methods - Part 25: Temperature
cycling
IEC 60749-26 - Semiconductor devices - Mechanical and EN IEC 60749-26 -
climatic test methods - Part 26: Electrostatic
discharge (ESD) sensitivity testing - Human
body model (HBM)
IEC 60825-1 - Safety of laser products - Part 1: Equipment EN 60825-1 -
classification and requirements
IEC 60950-1 - Information technology equipment - Safety - - -
Part 1: General requirements
IEC 61300-2-4 - Fibre optic interconnecting devices and EN IEC 61300-2-4 -
passive components - Basic test and
measurement procedures - Part 2-4: Tests -
Fibre or cable retention
3
---------------------- Page: 5 ----------------------
SIST EN IEC 62149-12:2023
EN IEC 62149-12:2023 (E)
Publication Year Title EN/HD Year
IEC 61300-2-19 - Fibre optic interconnecting devices and EN 61300-2-19 -
passive components - Basic test and
measurement procedures - Part 2-19: Tests -
Damp heat (steady state)
IEC 61300-2-48 - Fibre optic interconnecting devices and EN 61300-2-48 -
passive components - Basic test and
measurement procedures - Part 2-48: Tests -
Temperature-humidity cycling
IEC 62149-1 - Fibre optic active components and devices - EN 62149-1 -
Performance standards - Part 1: General and
guidance
4
---------------------- Page: 6 ----------------------
SIST EN IEC 62149-12:2023
IEC 62149-12
®
Edition 1.0 2023-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic active components and devices – Performance standards –
Part 12: Distributed feedback laser diode device for analogue radio over fibre
systems
Composants et dispositifs actifs fibroniques – Normes de performances –
Partie 12: Dispositif à diode laser à rétroaction répartie pour systèmes radio
analogiques sur fibre
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-6473-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 62149-12:2023
– 2 – IEC 62149-12:2023 © IEC 2023
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviated terms . 7
3.1 Terms and definitions . 7
3.2 Symbols . 7
3.3 Abbreviated terms . 8
4 Product parameters . 8
4.1 Absolute limiting ratings . 8
4.2 Operating environment . 8
4.3 Functional specifications . 8
5 Testing . 9
5.1 General . 9
5.2 Characterization testing . 9
5.3 Performance testing . 9
6 Environmental specifications . 9
6.1 General safety . 9
6.2 Laser safety . 9
6.3 Electromagnetic compatibility (EMC) requirements. 9
Annex A (normative) Specifications for DFB-LD devices for analogue RoF systems . 10
A.1 Absolute limiting ratings . 10
A.2 Operating environment . 10
A.3 Functional specifications . 10
A.4 Testing . 11
A.4.1 Characterization testing . 11
A.4.2 Performance testing. 11
Bibliography . 14
Table 1 – Operating case environment . 8
Table A.1 – Absolute limiting ratings . 10
Table A.2 – Operating conditions for functional specifications . 10
Table A.3 – Functional specifications . 11
Table A.4 – Performance test plan . 12
Table A.5 – Recommended performance test failure criteria . 13
---------------------- Page: 8 ----------------------
SIST EN IEC 62149-12:2023
IEC 62149-12:2023 © IEC 2023 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PERFORMANCE STANDARDS –
Part 12: Distributed feedback laser diode device
for analogue radio over fibre systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 62149-12 has been prepared by subcommittee 86C: Fibre optic systems and active devices,
of IEC technical committee 86: Fibre optics. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
86C/1808/CDV 86C/1840/RVC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
---------------------- Page: 9 ----------------------
SIST EN IEC 62149-12:2023
– 4 – IEC 62149-12:2023 © IEC 2023
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts of the IEC 62149 series, published under the general title Fibre op
...
SLOVENSKI STANDARD
SIST EN IEC 62149-12:2023
01-maj-2023
Optične aktivne komponente in naprave - Izvedbeni standardi - 12. del: Naprava z
diodo za porazdeljeno povratno lasersko sevanje za analogne radijske signale po
sistemih optičnih vlaken (IEC 62149-12:2023)
Fibre optic active components and devices - Performance standards - Part 12:
Distributed feedback laser diode device for analogue radio over fibre systems (IEC
62149-12:2023)
Aktive Lichtwellenleiterbauelemente und -geräte - Betriebsverhaltensnormen - Teil 12:
Laserdiodenbauelemente mit verteilter Rückkopplung für analoge
Funksignalübertragung über Glasfasersysteme (IEC 62149-12:2023)
Composants et dispositifs actifs fibroniques – Normes de performances – Partie 12:
Dispositif à diode laser à rétroaction répartie pour systèmes radio analogique sur fibre
(IEC 62149-12:2023)
Ta slovenski standard je istoveten z: EN IEC 62149-12:2023
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 62149-12:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 62149-12:2023
---------------------- Page: 2 ----------------------
SIST EN IEC 62149-12:2023
EUROPEAN STANDARD EN IEC 62149-12
NORME EUROPÉENNE
EUROPÄISCHE NORM March 2023
ICS 33.180.20
English Version
Fibre optic active components and devices - Performance
standards - Part 12: Distributed feedback laser diode device for
analogue radio over fibre systems
(IEC 62149-12:2023)
Composants et dispositifs actifs fibroniques - Normes de Aktive Lichtwellenleiterbauelemente und -geräte -
performances - Partie 12: Dispositif à diode laser à Betriebsverhaltensnormen - Teil 12:
rétroaction répartie pour systèmes radio analogiques sur Laserdiodenbauelemente mit verteilter Rückkopplung für
fibre analoge Funksignalübertragung über LWL-Systeme
(IEC 62149-12:2023) (IEC 62149-12:2023)
This European Standard was approved by CENELEC on 2023-03-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62149-12:2023 E
---------------------- Page: 3 ----------------------
SIST EN IEC 62149-12:2023
EN IEC 62149-12:2023 (E)
European foreword
The text of document 86C/1808/CDV, future edition 1 of IEC 62149-12, prepared by SC 86C "Fibre
optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 62149-12:2023.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-12-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-03-17
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62149-12:2023 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 62007-1 NOTE Approved as EN 62007-1
IEC 62149-2 NOTE Approved as EN 62149-2
IEC 62149-7 NOTE Approved as EN 62149-7
IEC 62149-8 NOTE Approved as EN 62149-8
IEC 62149-10 NOTE Approved as EN IEC 62149-10
2
---------------------- Page: 4 ----------------------
SIST EN IEC 62149-12:2023
EN IEC 62149-12:2023 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60749-6 - Semiconductor devices - Mechanical and EN 60749-6 -
climatic test methods - Part 6: Storage at high
temperature
IEC 60749-7 - Semiconductor devices - Mechanical and EN 60749-7 -
climatic test methods - Part 7: Internal
moisture content measurement and the
analysis of other residual gases
IEC 60749-10 - Semiconductor devices - Mechanical and EN IEC 60749-10 -
climatic test methods - Part 10: Mechanical
shock - device and subassembly
IEC 60749-11 - Semiconductor devices - Mechanical and EN 60749-11 -
climatic test methods - Part 11: Rapid change
of temperature - Two-fluid-bath method
IEC 60749-12 - Semiconductor devices - Mechanical and EN IEC 60749-12 -
climatic test methods - Part 12: Vibration,
variable frequency
IEC 60749-25 - Semiconductor devices - Mechanical and EN 60749-25 -
climatic test methods - Part 25: Temperature
cycling
IEC 60749-26 - Semiconductor devices - Mechanical and EN IEC 60749-26 -
climatic test methods - Part 26: Electrostatic
discharge (ESD) sensitivity testing - Human
body model (HBM)
IEC 60825-1 - Safety of laser products - Part 1: Equipment EN 60825-1 -
classification and requirements
IEC 60950-1 - Information technology equipment - Safety - - -
Part 1: General requirements
IEC 61300-2-4 - Fibre optic interconnecting devices and EN IEC 61300-2-4 -
passive components - Basic test and
measurement procedures - Part 2-4: Tests -
Fibre or cable retention
3
---------------------- Page: 5 ----------------------
SIST EN IEC 62149-12:2023
EN IEC 62149-12:2023 (E)
Publication Year Title EN/HD Year
IEC 61300-2-19 - Fibre optic interconnecting devices and EN 61300-2-19 -
passive components - Basic test and
measurement procedures - Part 2-19: Tests -
Damp heat (steady state)
IEC 61300-2-48 - Fibre optic interconnecting devices and EN 61300-2-48 -
passive components - Basic test and
measurement procedures - Part 2-48: Tests -
Temperature-humidity cycling
IEC 62149-1 - Fibre optic active components and devices - EN 62149-1 -
Performance standards - Part 1: General and
guidance
4
---------------------- Page: 6 ----------------------
SIST EN IEC 62149-12:2023
IEC 62149-12
®
Edition 1.0 2023-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic active components and devices – Performance standards –
Part 12: Distributed feedback laser diode device for analogue radio over fibre
systems
Composants et dispositifs actifs fibroniques – Normes de performances –
Partie 12: Dispositif à diode laser à rétroaction répartie pour systèmes radio
analogiques sur fibre
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-6473-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 62149-12:2023
– 2 – IEC 62149-12:2023 © IEC 2023
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviated terms . 7
3.1 Terms and definitions . 7
3.2 Symbols . 7
3.3 Abbreviated terms . 8
4 Product parameters . 8
4.1 Absolute limiting ratings . 8
4.2 Operating environment . 8
4.3 Functional specifications . 8
5 Testing . 9
5.1 General . 9
5.2 Characterization testing . 9
5.3 Performance testing . 9
6 Environmental specifications . 9
6.1 General safety . 9
6.2 Laser safety . 9
6.3 Electromagnetic compatibility (EMC) requirements. 9
Annex A (normative) Specifications for DFB-LD devices for analogue RoF systems . 10
A.1 Absolute limiting ratings . 10
A.2 Operating environment . 10
A.3 Functional specifications . 10
A.4 Testing . 11
A.4.1 Characterization testing . 11
A.4.2 Performance testing. 11
Bibliography . 14
Table 1 – Operating case environment . 8
Table A.1 – Absolute limiting ratings . 10
Table A.2 – Operating conditions for functional specifications . 10
Table A.3 – Functional specifications . 11
Table A.4 – Performance test plan . 12
Table A.5 – Recommended performance test failure criteria . 13
---------------------- Page: 8 ----------------------
SIST EN IEC 62149-12:2023
IEC 62149-12:2023 © IEC 2023 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PERFORMANCE STANDARDS –
Part 12: Distributed feedback laser diode device
for analogue radio over fibre systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 62149-12 has been prepared by subcommittee 86C: Fibre optic systems and active devices,
of IEC technical committee 86: Fibre optics. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
86C/1808/CDV 86C/1840/RVC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
---------------------- Page: 9 ----------------------
SIST EN IEC 62149-12:2023
– 4 – IEC 62149-12:2023 © IEC 2023
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts of the IEC 62149 series, published under the general title Fibre o
...
SLOVENSKI STANDARD
oSIST prEN IEC 62149-12:2022
01-oktober-2022
Aktivne komponente in naprave optičnih vlaken - Izvedbeni standardi - 12. del:
Naprava z diodo za porazdeljeno povratno lasersko sevanje za analogne radijske
signale po sistemih optičnih vlaken
Fibre optic active components and devices - Performance standards - Part 12:
Distributed feedback laser diode device for analogue radio over fibre systems
Ta slovenski standard je istoveten z: prEN IEC 62149-12:2022
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
oSIST prEN IEC 62149-12:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN IEC 62149-12:2022
---------------------- Page: 2 ----------------------
oSIST prEN IEC 62149-12:2022
86C/1808/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 62149-12 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2022-07-22 2022-10-14
SUPERSEDES DOCUMENTS:
86C/1766/CD, 86C/1794/CC
IEC SC 86C : FIBRE OPTIC SYSTEMS AND ACTIVE DEVICES
SECRETARIAT: SECRETARY:
United States of America Mr Fred Heismann
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
TITLE:
Fibre optic active components and devices – Performance standards – Part 12:
Distributed feedback laser diode device for analogue radio over fibre systems
PROPOSED STABILITY DATE: 2026
NOTE FROM TC/SC OFFICERS:
Copyright © 2022 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 62149-12:2022
IEC CDV 62149-12/Ed1 © IEC:2022 – 2 – 86C/1808/CDV
1 CONTENTS
2 FOREWORD . 3
3 INTRODUCTION . 5
4 1 Scope . 6
5 2 Normative references . 6
6 3 Terms, definitions, symbols and abbreviated terms . 6
7 3.1 Terms and definitions. 6
8 3.2 Symbols . 7
9 3.3 Abbreviated terms . 8
10 4 Product parameters . 8
11 4.1 Absolute limiting ratings . 8
12 4.2 Operating environment . 8
13 4.3 Functional specifications . 8
14 5 Testing . 8
15 5.1 General . 8
16 5.2 Characterization testing . 8
17 5.3 Performance testing . 8
18 6 Environmental specifications . 9
19 6.1 General safety . 9
20 6.2 Laser safety . 9
21 6.3 Electromagnetic compatibility (EMC) requirements . 9
22 Annex A . 10
23 A.1 Absolute limiting ratings . 10
24 A.2 Operating environment . 10
25 A.3 Functional specifications . 10
26 A.4 Testing . 11
27 A.4.1 Characterization testing . 11
28 A.4.2 Performance testing . 11
29 Bibliography . 14
30 Table 1 – Operating case environment . 8
31 Table A.1 – Absolute limiting ratings . 10
32 Table A.2 – Operating conditions for functional specifications . 10
33 Table A.3 – Functional specifications . 11
34 Table A.4 – Performance test plan . 12
35 Table A.5 – Recommended performance test failure criteria . 13
36
37
---------------------- Page: 4 ----------------------
oSIST prEN IEC 62149-12:2022
IEC CDV 62149-12/Ed1 © IEC:2022 – 3 – 86C/1808/CDV
38 INTERNATIONAL ELECTROTECHNICAL COMMISSION
39 ____________
40
41 FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
42 PERFORMANCE STANDARDS –
43
44 Part 12: Distributed feedback laser diode device for analogue radio over
45 fibre systems
46
47 FOREWORD
48 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
49 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
50 international co-operation on all questions concerning standardization in the electrical and electronic fields. To
51 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
52 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
53 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
54 in the subject dealt with may participate in this preparatory work. International, governmental and non-
55 governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
56 with the International Organization for Standardization (ISO) in accordance with conditions determined by
57 agreement between the two organizations.
58 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
59 consensus of opinion on the relevant subjects since each technical committee has representation from all
60 interested IEC National Committees.
61 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
62 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
63 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
64 misinterpretation by any end user.
65 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
66 transparently to the maximum extent possible in their national and regional publications. Any divergence
67 between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
68 the latter.
69 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
70 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
71 services carried out by independent certification bodies.
72 6) All users should ensure that they have the latest edition of this publication.
73 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
74 members of its technical committees and IEC National Committees for any personal injury, property damage or
75 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
76 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
77 Publications.
78 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
79 indispensable for the correct application of this publication.
80 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
81 patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
82 IEC 62149-12 has been prepared by subcommittee 86C: Fibre optic systems and active
83 devices, of IEC technical committee 86: Fibre optics. It is an International Standard.
84 The text of this International Standard is based on the following documents:
Draft Report on voting
XX/XX/FDIS XX/XX/RVD
85
86 Full information on the voting for its approval can be found in the report on voting indicated in
87 the above table.
88 The language used for the development of this International Standard is English.
89 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
90 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement,
---------------------- Page: 5 ----------------------
oSIST prEN IEC 62149-12:2022
IEC CDV 62149-12/Ed1 © IEC:2022 – 4 – 86C/1808/CDV
91 available at www.iec.ch/members_experts/refdocs. The main document types developed by
92 IEC are described in greater detail at www.iec.ch/standardsdev/publications.
93 A list of all parts of the IEC 62149 series, published under the general title Fibre optic active
94 components and devices – Performance standards, can be found on the IEC website.
95 The committee has decided that the contents of this document will remain unchanged until the
96 stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
97 the specific document. At this date, the document will be
98 • reconfirmed,
99 • withdrawn,
100 • replaced by a revised edition, or
101 • amended.
102
103
104
---------------------- Page: 6 ----------------------
oSIST prEN IEC 62149-12:2022
IEC CDV 62149-12/Ed1 © IEC:2022 – 5 – 86C/1808/CDV
105 INTRODUCTION
106 Distributed feedback laser diode (DFB-LD) devices for analogue radio over fibre (A-RoF)
107 systems are used to convert electrical radio signals into optical signals. This part of IEC
108 62149 covers the performance specification for DFB-LD devices in A-RoF systems. The
109 optical and electrical performance criteria are generally well specified for a number of
110 internationally agreed upon application areas, such as ITU-T Recommendation G.9803 and
111 IEC 62149-10. This standard provides optical and electrical performance specifications for
112 RoF transceivers. These transceivers are necessary for operation of A-RoF systems, because
113 the RoF transmitter requires a light source such as a DFB-LD device. DFB-LD devices for RoF
114 transceivers are supplied by different manufacturers. However, they do not guarantee the
115 operation of DFB-LD devices in A-RoF systems. Manufacturers using the standards are
116 responsible for meeting the required performance and/or reliability and quality assurance
117 under a recognized scheme.
118
---------------------- Page: 7 ----------------------
oSIST prEN IEC 62149-12:2022
IEC CDV 62149-12/Ed1 © IEC:2022 – 6 – 86C/1808/CDV
119 FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
120 PERFORMANCE STANDARDS –
121
122 Part 12: Distributed feedback laser diode device for analogue Radio over
123 Fibre systems
124
125 1 Scope
126 This part of IEC 62149 defines performance specifications for distributed feedback laser diode
127 (DFB-LD) devices used in analogue radio over fibre (RoF) systems. It defines product
128 performance requirements together with a series of tests and measurements with clearly
129 defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a
130 “once-off” basis to prove a product’s ability to satisfy the performance requirements.
131 2 Normative references
132 The following documents are referred to in the text in such a way that some or all of their
133 content constitutes requirements of this document. For dated references, only the edition
134 cited applies. For undated references, the latest edition of the referenced document (including
135 any amendments) applies.
136 IEC 60749-6, Semiconductor devices - Mechanical and climatic test methods - Part 6: Storage
137 at high temperature
138 IEC 60749-7, Semiconductor devices - Mechanical and climatic test methods - Part 7: Internal
139 moisture content measurement and the analysis of other residual gases
140 IEC 60749-10, Semiconductor devices - Mechanical and climatic test methods - Part 10:
141 Mechanical shock
142 IEC 60749-11, Semiconductor devices - Mechanical and climatic test methods - Part 11:
143 Rapid ch
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.