SIST EN 71-7:2014+A1:2017
(Main)Safety of toys - Part 7: Finger paints - Requirements and test methods
Safety of toys - Part 7: Finger paints - Requirements and test methods
This part of EN 71 specifies requirements for the substances and materials used in finger paints and applies to finger paints only.
Additional requirements are specified for markings, labelling and containers.
Sicherheit von Spielzeug - Teil 7: Fingermalfarben - Anforderungen und Prüfverfahren
Dieser Teil der EN 71 legt Anforderungen an die in Fingermalfarben verwendeten Stoffe und Materialien fest und gilt nur für Fingermalfarben.
Für Beschriftung, Kennzeichnung und Behälter sind zusätzliche Anforderungen festgelegt.
Sécurité des jouets - Partie 7: Peintures au doigt - Exigences et méthodes d'essai
La présente partie de l'EN 71 fixe des exigences relatives aux substances et produits utilisés dans les peintures au doigt et s’applique uniquement aux peintures au doigt.
Des exigences complémentaires sont données pour le marquage, l'étiquetage et l'emballage.
Varnost igrač - 7. del: Prstne barve - Zahteve in preskusne metode (vključno z dopolnilom A1)
Ta del standarda EN 71 določa zahteve za snovi in materiale, ki se uporabljajo v prstnih barvah in veljajo samo za prstne barve.
Dodatne zahteve so določene za označevanje, etiketiranje in embalažo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 71-7:2014+A1:2017
01-december-2017
1DGRPHãþD
SIST EN 71-7:2014
9DUQRVWLJUDþGHO 3UVWQHEDUYH=DKWHYHLQSUHVNXVQHPHWRGH YNOMXþQR]
GRSROQLORP$
Safety of toys - Part 7: Finger paints - Requirements and test methods
Sicherheit von Spielzeug - Teil 7: Fingermalfarben - Anforderungen und Prüfverfahren
Sécurité des jouets - Partie 7: Peintures au doigt - Exigences et méthodes d'essai
Ta slovenski standard je istoveten z: EN 71-7:2014+A1:2017
ICS:
97.200.50 ,JUDþH Toys
SIST EN 71-7:2014+A1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 71-7:2014+A1:2017
---------------------- Page: 2 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2017
EUROPÄISCHE NORM
ICS 97.200.50 Supersedes EN 71-7:2014
English Version
Safety of toys - Part 7: Finger paints - Requirements and
test methods
Sécurité des jouets - Partie 7: Peintures au doigt - Sicherheit von Spielzeug - Teil 7: Fingermalfarben -
Exigences et méthodes d'essai Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 8 February 2014 and includes Amendment 1 approved by CEN on 31 August
2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 71-7:2014+A1:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
Contents Page
European foreword . 5
Introduction . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Requirements . 9
4.1 General . 9
4.2 Colourants . 9
4.3 Preservatives . 10
4.4 Migration of certain elements . 10
4.5 Limits for impurities . 10
4.5.1 Limits for primary aromatic amines . 10
4.5.2 Limits for other impurities . 11
4.6 Taste and smell . 12
4.7 pH-value . 12
4.8 Binding agents, extenders, humectants and surfactants . 12
4.9 N-Nitrosamines . 12
4.10 Containers . 13
5 Product information . 13
5.1 General . 13
5.2 Marking . 13
5.2.1 Primary packaging . 13
5.2.2 Container . 14
Annex A (informative) Non-exhaustive list of colourants which are commonly used in finger
paints, and need to be in compliance with both the general and specified purity
requirements . 15
Annex B (normative) List of preservatives allowed for use in finger paints . 21
Annex C (informative) Ingredients used in the manufacture of finger paints . 26
Annex D (normative) Method for the detection of certain azo colourants and determination
of free primary aromatic amines . 28
D.1 General . 28
D.2 Reagents . 29
D.3 Apparatus . 30
D.4 Instrumentation . 30
D.5 Sampling procedure . 30
D.6 Procedure. 30
D.7 Calculation . 40
D.8 Precision . 41
D.8.1 Linearity . 41
2
---------------------- Page: 4 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
D.8.2 Limits of Detection (LOD) and Quantification (LOQ) . 41
D.8.3 Repeatability and reproducibility data for soluble aromatic amines . 42
D.8.4 Repeatability and reproducibility data for reductively cleaved aromatic amines . 43
D.8.5 Recovery . 44
D.9 Report . 46
D.10 Additional Information . 46
Annex E (normative) Method for the determination of hexachlorobenzene, polychlorinated
biphenyls and benzo[α]pyrene . 47
E.1 Principle . 47
E.2 Standards, reagents and solvents . 47
E.3 Apparatus . 49
E.4 Instrumentation . 49
E.5 Sampling . 50
E.6 Procedure . 50
E.6.1 General . 50
E.6.2 Sample preparation . 50
E.6.3 Solvent extraction . 50
E.6.4 Solid phase extraction . 51
E.6.5 Sample concentration for determining HCB and PCB congeners . 51
E.6.6 Sample concentration for determining B[α]P . 51
E.6.7 Gas chromatography conditions . 51
E.6.8 Mass spectrometry . 52
E.6.9 SIM mode . 52
E.7 Calculation. 57
E.8 Precision . 59
E.8.1 Linearity . 59
E.8.2 Limits of detection (LOD) and Quantification (LOQ) . 59
E.8.3 Repeatability and reproducibility data for HCB, PCB congeners and B[α]P . 59
E.8.4 Recovery . 60
E.9 Report . 60
E.10 Additional information . 61
Annex F (informative) Rationale . 64
F.1 Finger paints (see 3.1 and 3.2) . 64
F.2 Colourants (see 4.2.1) . 64
F.3 Preservatives (see 4.3) . 64
F.4 Elements (see 4.4) . 64
F.5 Primary aromatic amines (see 4.5.1.2, Tables 1 and 2 and Annex D) . 64
3
---------------------- Page: 5 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
F.6 Limit for Benzo[α]Pyrene (see 4.5.2) . 65
F.7 Embittering agents (see 4.6) . 65
F.8 pH value (see 4.7) . 65
F.9 N-Nitrosamines (see 4.9) . 65
F.10 Container (see 4.10) . 65
F.11 Labelling phrases (see 5.2.1.2) . 66
F.12 List of polychlorinated biphenyl congeners (see Annex E). 66
F.13 Reference materials (see Annex D and E) . 66
F.14 PCB Analytical Method (see E.6) . 67
Annex G (informative) Significant technical changes between this European Standard and
the previous version . 68
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2009/48/EC . 70
Bibliography . 71
4
---------------------- Page: 6 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
European foreword
This document (EN 71-7:2014+A1:2017) has been prepared by Technical Committee CEN/TC 52
“Safety of toys”, the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2018 and conflicting national standards shall be
withdrawn at the latest by March 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes !EN 71-7:2014".
This document includes Amendment 1 approved by CEN on 2017-08-31.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2009/48/EC.
For relationship with EU Directive 2009/48/EC, see informative Annex ZA, which is an integral part of
this document.
EN 71, Safety of toys, consists of the following parts:
— Part 1: Mechanical and physical properties
— Part 2: Flammability
— Part 3: Migration of certain elements
— Part 4: Experimental sets for chemistry and related activities
— Part 5: Chemical toys (sets) other than experimental sets
— Part 7: Finger paints – Requirements and test methods
— Part 8: Activity toys for domestic use
— Part 9: Organic chemical compounds – Requirements
— Part 10: Organic chemical compounds – Sample preparation and extraction
— Part 11: Organic chemical compounds – Methods of analysis
— Part 12: N-Nitrosamines and N-nitrosatable substances
— Part 13: Olfactory board games, cosmetic kits and gustative games
— Part 14: Trampolines for domestic use
5
---------------------- Page: 7 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
!NOTE 1 In addition to the above parts of EN 71, the following guidance documents have been published:
CEN Technical Report CEN/TR 15071, Safety of toys - National translations of warnings and instructions for use in
EN 71 and CEN/TR 15371 (all parts), Safety of toys – Interpretations."
This part 7 of the EN 71 series is intended to be read in conjunction with EN 71, part 1.
NOTE 2 Words in italics are defined in Clause 3 (Terms and definitions).
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
6
---------------------- Page: 8 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
Introduction
This European Standard contains requirements which are intended to reduce the risks to children when
finger paints are used as intended or in a foreseeable way, bearing in mind the behaviour of children. It
is intended to complete the essential safety requirements of Directive 2009/48/EC by providing special
requirements for finger paints.
It is recognized that finger paints when compared to other toy products present different risks because
of the intended use by fingers or hands and the age of the child. For example, prolonged skin contact or
possible ingestion of paint material cannot be ruled out. Therefore, the safety requirements outlined in
other parts of EN 71 needed to be expanded upon for finger paints. In order to address the risks
associated with the use of finger paints by children, this part of EN 71 contains requirements relating to
preservatives as well as other ingredients that may be used in the manufacture of finger paints and
requirements relating to impurities, migration of certain elements and other attributes.
Chemical Abstract Service Registry Number (CAS), European Inventory of Existing Chemical Substances
Number (EINECS) or Colour Index Number given in the tables are provided for information purposes
only.
7
---------------------- Page: 9 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
1 Scope
This part of EN 71 specifies requirements for the substances and materials used in finger paints and
applies to finger paints only.
Additional requirements are specified for markings, labelling and containers.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 71-3, Safety of toys - Part 3: Migration of certain elements
EN 71-12, Safety of toys - Part 12: N-Nitrosamines and N-nitrosatable substances
EN ISO 787-9, General methods of test for pigments and extenders - Part 9: Determination of pH value of
aqueous suspension (ISO 787-9)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
finger paint
aqueous semi-solid or liquid, coloured mixture specially designed for children to apply directly to
suitable surfaces with the fingers and hands
3.2
colourant
pigment or dyestuff
Note 1 to entry: For definitions of pigment and dyestuff, see EN ISO 4618.
3.3
extender
material in granular or powder form, insoluble in the medium and used to modify or influence certain
physical properties
[SOURCE: EN ISO 4618:2006, 2.98]
3.4
humectant
substance that delays the drying process
3.5
binding agent
water soluble or miscible, non-volatile component that binds the paint to the surface to which it has
been applied
3.6
preservative
substance that prevents the growth of undesirable micro-organisms
8
---------------------- Page: 10 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
3.7
surfactant
surface active substance
3.8
embittering agent
substance that gives the product a bitter taste
4 Requirements
NOTE The requirements of this standard apply to finger paints in the form used by the child. In the case of
powdered finger paints (for example to which water might be added before use) the requirements apply to the
finger paint prepared according to the manufacturer's instructions.
4.1 General
Finger paints shall not contain dangerous substances or mixtures in amounts which can harm the health
of children using them.
NOTE 1 For more information, see Directive 1999/45/EC [2] and Regulation No. (EC) 1272/2008 [1].
Finger paints shall not fulfil the criteria of any of the following hazard classes:
— “acute toxicity” (hazard class 3.1),
— “Skin corrosion/irritation” (hazard class 3.2),
— “Serious eye damage/eye irritation” (hazard class 3.3),
— “Respiratory or skin sensitisation” (hazard class 3.4),
— “Germ cell mutagenicity” (hazard class 3.5),
— “Carcinogenicity” (hazard class 3.6),
— “Reproductive toxicity” (hazard class 3.7),
— “Specific target organ toxicity — single exposure” (hazard class 3.8),
— “Specific target organ toxicity — repeated exposure” (hazard class 3.9),
— “Aspiration hazard” (hazard class 3.10).
NOTE 2 The classification is detailed in Regulation (EC) No. 1272/2008 [1] (Annex I, Part 3: Health Hazards).
4.2 Colourants
4.2.1 Only colourants and colouring materials which are not fulfilling the hazard criteria in 4.1 shall
be used in finger paints.
NOTE A non-exhaustive list of commonly used colourants, subject to meeting purity requirements, is given in
Annex A consisting of colourants falling in one or more of the following categories: Colourants permitted for use in
food and/or cosmetics and other pigments which meet the general requirements of 4.1.
9
---------------------- Page: 11 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
4.2.2 Finger paints shall not contain azo colourants that by cleavage of one or more azo groups can
produce the primary aromatic amines listed in Tables 1 and 2 when tested in accordance with the test
method specified in Annex D.
4.3 Preservatives
Finger paints shall be preserved using only the preservatives listed in Annex B. The determination of
preservatives shall be in accordance with the methods approved under EU Cosmetics Legislation, where
available (see Directive 82/434/EEC [6], Directive 83/514/EEC [7], Directive 85/490/EEC [8],
Directive 93/73/EEC [9], Directive 95/32/EC [10], Directive 96/45/EC [11]). When tested in
accordance with these methods, the maximum concentrations specified in the column ”maximum
allowed concentration” of Table B.1 and the limitations and requirements specified in the column
”Limitations and requirements” of Table B.1 shall be observed.
4.4 Migration of certain elements
When tested in accordance with EN 71-3 the concentration of elements shall not exceed the limit values
specified in EN 71-3.
4.5 Limits for impurities
4.5.1 Limits for primary aromatic amines
4.5.1.1 The primary aromatic amines listed in Table 1 shall not be determinable when tested in
accordance with the test method in Annex D.
Table 1 — Primary aromatic amines
Primary aromatic amines CAS number
Benzidine 92–87–5
2-Naphthylamine 91–59–8
95–69–2
4-Chloro-2-methyl-aniline (4-Chloro-o-
toluidine)
4-Aminobiphenyl 92–67–1
4.5.1.2 Finger paints shall not contain carcinogenic primary aromatic amines (see Table 2 for a non-
exhaustive list of relevant substances) in a total amount exceeding 20 mg/kg, with no individual
primary aromatic amine exceeding 10 mg/kg, when tested in accordance with Annex D. The limitation
does not apply to aromatic aminocarboxylic acids or aminosulfonic acids.
10
---------------------- Page: 12 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
Table 2 — Other carcinogenic primary aromatic amines (non-exhaustive list)
Carcinogenic primary aromatic amine CAS number
o-Aminoazotoluene (4-o-tolyazo-o-toluidine) 97–56–3
2-Amino-4-nitro-toluene (5-Nitro-o-toluidine) 99–55–8
4-Chloroaniline 106–47–8
2,4-Diaminoanisole 615–05–4
4,4'-Diaminodiphenylmethane (4,4'-Methylenedianiline) 101–77–9
a
91–94–1
3,3'-Dichlorobenzidine
3,3'-Dimethoxybenzidine 119–90–4
3,3'-Dimethylbenzidine 119–93–7
3,3'-Dimethyl-4,4'-diaminodiphenylmethane 838–88–0
p-Cresidine (6-Methoxy-m-toluidine) 120–71–8
101–14–4
2,2’-Dichloro-4,4’-methylenedianiline
(4,4'-Methylene-bis-2-chloroaniline)
4,4'-Oxydianiline 101–80–4
4,4'-Thiodianiline 139–65–1
o-Toluidine 95–53–4
2,4-Xylidine 95–68–1
2,6-Xylidine 87–62–7
4-Amino-3-fluorophenol 399–95–1
6-Amino-2-ethoxynaphthalene 293733–21–8
2-Methoxyaniline (o-anisidine) 90–04–0
4-Aminoazobenzene 60–09–3
4-Methyl-m-phenylenediamine 95–80–7
(Toluene-2,4-diamine)
2,4,5-Trimethylaniline 137–17–7
Aniline 62–53–3
a
For certain pigments limit values for 3,3’-Dichlorobenzidine are given Annex A.
4.5.2 Limits for other impurities
Finger paints shall not contain the impurities specified in Table 3, column 1 above the limits specified in
column 2 when colourants specified in Table 3, column 3 are used, when tested in accordance with
Annex E.
11
---------------------- Page: 13 ----------------------
SIST EN 71-7:2014+A1:2017
EN 71-7:2014+A1:2017 (E)
Table 3 — Impurities in finger paints
Impurity Limit Finger paints of concern
mg/kg
Polychlorinated 2 Finger paints containing
biphenyls colourant products
containing chlorine or
manufactured in chlorinated
solvents
Hexachlorobenzene 5 Finger paints containing
colourant products
containing chlorine or
manufactured in chlorinated
solvents
Benzo (a) pyrene 0,05 Only for finger paints
containing carbon black
4.6 Taste and smell
Finger paints shall not be sweetened, flavoured or fragranced.
An embittering agent in accordance with the following list (see Table 4) shall be added in order to
discourage and minimize the ingestion of paint. The bitterness shall stay in the product during product
lifetime.
The bitterness should be sensorically detectable in a dilution with water 1:100.
Table 4 — Embittering agents
Embittering agent CAS number
Naringin CAS 10236–47–2
denatonium benzoate CAS 3734–33–6
NOTE The relative bitterness of these substances is approximately 1:3000 (naringin : denatonium benzoate).
The following levels have been found suitable: naringin 1 %; denatonium benzoate 0,0004 % (4 mg/kg).
4.7 pH-value
The pH-value of the finger paint shall be between 4,0 and 10,0 when tested in accordance with
EN I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.