SIST EN 3819:2008
(Main)Aerospace series - Clearance for wrenches and sockets
Aerospace series - Clearance for wrenches and sockets
This standard defines the minimum clearance area required around nuts and bolt heads when using either double hexagon box or socket wrenches defined in AECMA standard.
Luft- und Raumfahrt - Platzbedarf für Schraubwerkzeuge
Diese Norm legt den Mindestplatzbedarf rund um Muttern und Schraubenköpfe bei der Anwendung von Ringschlüsseln oder Steckschlüsseleinsätzen mit Doppelsechskant nach AECMA-Normen fest.
Série aérospatiale - Dégagements pour clés et douilles
Aeronavtika - Prost prostor za vijačno orodje
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 3819:2008
01-september-2008
$HURQDYWLND3URVWSURVWRU]DYLMDþQRRURGMH
Aerospace series - Clearance for wrenches and sockets
Luft- und Raumfahrt - Platzbedarf für Schraubwerkzeuge
Série aérospatiale - Dégagements pour clés et douilles
Ta slovenski standard je istoveten z: EN 3819:2008
ICS:
49.030.99 Drugi vezni elementi Other fasteners
SIST EN 3819:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 3819
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2008
ICS 49.030.99
English Version
Aerospace series - Clearance for wrenches and sockets
Série aérospatiale - Dégagements pour clés et douilles Luft- und Raumfahrt - Platzbedarf für Schraubwerkzeuge
This European Standard was approved by CEN on 12 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3819:2008: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 3819:2008 (E)
Contents Page
Foreword.3
1 Scope.4
2 Normative references.4
3 Clearance for box wrench according to EN 3711.4
4 Clearance for socket wrench according to EN 3710.5
Figures
Figure 1 . 4
Figure 2 . 4
Figure 3 . 4
Figure 4 . 5
Figure 5 . 5
Tables
Table 1. 5
Table 2. 6
2
---------------------- Page: 3 ----------------------
EN 3819:2008 (E)
Foreword
This document (EN 3819:2008) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn
at the latest by November 2008.
Attention is drawn to the possi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.