SIST EN 1715-2:2008
(Main)Aluminium and aluminium alloys - Drawing stock - Part 2: Specific requirements for electrical applications
Aluminium and aluminium alloys - Drawing stock - Part 2: Specific requirements for electrical applications
This Part of EN 1715 applies to drawing stock of aluminium and aluminium alloys for electrical conductor and cables and specifies characteristics and specific technical conditions for inspection and delivery of the products. The general requirements and technical conditions for inspection and delivery are specified in prEN 1715-1.
The standard does not apply to drawn wire.
Aluminium und Aluminiumlegierungen - Vordraht - Teil 2: Besondere Anforderungen für elektrotechnische Anwendungen
Diese Europäische Norm legt die besonderen Anforderungen an Vordraht aus Aluminium und
Aluminiumlegierungen für elektrotechnische Anwendungen fest.
Die allgemeinen Anforderungen und Technischen Lieferbedingungen sind in EN 1715-1 festgelegt.
Diese Europäische Norm gilt nicht für gezogenen Draht.
Aluminium et alliages d'aluminium - Fil machine - Partie 2: Exigences spécifiques pour les applications électriques
Ce document (prEN 1715-2:2006) spécifie les exigences spécifiques pour le fil machine en aluminium et alliages d'aluminium pour applications électriques. Il s'applique aux conducteurs électriques et aux câbles.
Les conditions générales de contrôle et de livraison sont spécifiées dans le prEN 1715-1.
Cette norme ne s'applique pas au fil étiré.
Aluminij in aluminijeve zlitine – Valjana žica – 2. del: Posebne zahteve za uporabo v elektrotehniki
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1715-2:2008
01-julij-2008
Nadomešča:
SIST EN 1715-2:1998
SIST EN 1715-2:1998/AC:2004
Aluminij in aluminijeve zlitine – Valjana žica – 2. del: Posebne zahteve za uporabo
v elektrotehniki
Aluminium and aluminium alloys - Drawing stock - Part 2: Specific requirements for
electrical applications
Aluminium und Aluminiumlegierungen - Vordraht - Teil 2: Besondere Anforderungen für
elektrotechnische Anwendungen
Aluminium et alliages d'aluminium - Fil machine - Partie 2: Exigences spécifiques pour
les applications électriques
Ta slovenski standard je istoveten z: EN 1715-2:2008
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 1715-2:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1715-2:2008
---------------------- Page: 2 ----------------------
SIST EN 1715-2:2008
EUROPEAN STANDARD
EN 1715-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 77.150.10 Supersedes EN 1715-2:1997
English Version
Aluminium and aluminium alloys - Drawing stock - Part 2:
Specific requirements for electrical applications
Aluminium et alliages d'aluminium - Fil machine - Partie 2: Aluminium und Aluminiumlegierungen - Vordraht - Teil 2:
Exigences spécifiques relatives aux applications électriques Besondere Anforderungen für elektrotechnische
Anwendungen
This European Standard was approved by CEN on 14 March 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1715-2:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1715-2:2008
EN 1715-2:2008 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Requirements.4
3.1 Chemical composition .4
3.2 Temper for delivery.5
4 Product inspection and testing methods.6
4.1 Chemical composition .6
4.2 Mechanical properties.6
4.3 Specific electrical resistivity (or conductivity) .6
5 Delivery documents and inspection documents.6
6 Marking and packaging.7
Annex A (normative) Chemical composition of aluminium alloys EN AW-1110, EN AW-8030 and
EN AW-8176.8
2
---------------------- Page: 4 ----------------------
SIST EN 1715-2:2008
EN 1715-2:2008 (E)
Foreword
This document (EN 1715-2:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by October 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document will supersede EN 1715-2:1997.
Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 "Wires and
drawing stock" to revise EN 1715-2:1997.
Besides editorial adjustments in the text and update of normative references, the following changes have
been made:
Clause 3: amended; Table 1 inclusion of alloys EN AW-1110, EN AW-5005, EN AW-8030 and
EN AW-8176;
Clause 4: amended.
EN 1715 comprises the following parts under the general title: "Aluminium and aluminium alloys – Drawing
stock":
Part 1: General requirements and technical conditions for inspection and delivery
Part 2: Specific requirements for electrical applications
Part 3: Specific requirements for mechanical uses (excluding welding)
Part 4: Specific requirements for welding applications
1)
Part 5: Specific requirements for aluminium food packaging
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
CEN/TC 132 affirms that it is its policy that in the case when a patentee refuses to grant licenses on
standardised standard products under reasonable and not discriminatory conditions, then this product is
removed from the corresponding standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sl
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Drawing stock - Part 2: Specific requirements for electrical applicationsAluminium et alliages d'aluminium - Fil machine - Partie 2: Exigences spécifiques pour les applications électriquesAluminium und Aluminiumlegierungen - Vordraht - Teil 2: Besondere Anforderungen für elektrotechnische Anwendungen77.150.10Aluminijski izdelkiAluminium productsICS:SIST EN 1715-2:2008en,fr,deTa slovenski standard je istoveten z:EN 1715-2:200801-julij-2008SIST EN 1715-2:2008SLOVENSKI
STANDARDSIST EN 1715-2:1998/AC:2004SIST EN 1715-2:19981DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1715-2April 2008ICS 77.150.10Supersedes EN 1715-2:1997
English VersionAluminium and aluminium alloys - Drawing stock - Part 2:Specific requirements for electrical applicationsAluminium et alliages d'aluminium - Fil machine - Partie 2:Exigences spécifiques relatives aux applications électriquesAluminium und Aluminiumlegierungen - Vordraht - Teil 2:Besondere Anforderungen für elektrotechnischeAnwendungenThis European Standard was approved by CEN on 14 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1715-2:2008: E
EN 1715-2:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Requirements.4 3.1 Chemical composition.4 3.2 Temper for delivery.5 4 Product inspection and testing methods.6 4.1 Chemical composition.6 4.2 Mechanical properties.6 4.3 Specific electrical resistivity (or conductivity).6 5 Delivery documents and inspection documents.6 6 Marking and packaging.7 Annex A (normative)
Chemical composition of aluminium alloys EN AW-1110, EN AW-8030 and EN AW-8176.8
EN 1715-2:2008 (E) 3 Foreword This document (EN 1715-2:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document will supersede EN 1715-2:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 "Wires and drawing stock" to revise EN 1715-2:1997. Besides editorial adjustments in the text and update of normative references, the following changes have been made: Clause 3: amended; Table 1 inclusion of alloys EN AW-1110, EN AW-5005, EN AW-8030 and EN AW-8176; Clause 4: amended. EN 1715 comprises the following parts under the general title: "Aluminium and aluminium alloys – Drawing stock": Part 1: General requirements and technical conditions for inspection and delivery Part 2: Specific requirements for electrical applications Part 3: Specific requirements for mechanical uses (excluding welding) Part 4: Specific requirements for welding applications Part 5: Specific requirements for aluminium food packaging1) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lux
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Drawing stock - Part 2: Specific requirements for electrical applicationsAluminium et alliages d'aluminium - Fil machine - Partie 2: Exigences spécifiques pour les applications électriquesAluminium und Aluminiumlegierungen - Vordraht - Teil 2: Besondere Anforderungen für elektrotechnische AnwendungenTa slovenski standard je istoveten z:EN 1715-2:2008kSIST prEN 1715-2:2008en77.150.10ICS:SIST EN 1715-2:1998/AC:2004SIST EN 1715-2:19981DGRPHãþDSLOVENSKI
STANDARDkSIST prEN 1715-2:200801-julij-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMFINAL DRAFTprEN 1715-2December 2007ICS 77.150.10Will supersede EN 1715-2:1997
English VersionAluminium and aluminium alloys - Drawing stock - Part 2:Specific requirements for electrical applicationsAluminium et alliages d'aluminium - Fil machine - Partie 2:Exigences spécifiques relatives aux applications électriquesAluminium und Aluminiumlegierungen - Vordraht - Teil 2:Besondere Anforderungen für elektrotechnischeAnwendungenThis draft European Standard is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC132.If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations whichstipulate the conditions for giving this European Standard the status of a national standard without any alteration.This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other languagemade by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has thesame status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice andshall not be referred to as a European Standard.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. prEN 1715-2:2007: E
prEN 1715-2:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Requirements.4 3.1 Chemical composition.4 3.2 Temper for delivery.5 4 Product inspection and testing methods.6 4.1 Chemical composition.6 4.2 Mechanical properties.6 4.3 Specific electrical resistivity (or conductivity).6 5 Delivery documents and inspection documents.6 6 Marking and packaging.7 Annex A (normative)
Chemical composition of aluminium alloys EN AW-1110, EN AW-8030 and EN AW-8176.8
prEN 1715-2:2007 (E) 3 Foreword This document (prEN 1715-2:2007) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This document is currently submitted to the Formal Vote. This document will supersede EN 1715-2:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 "Wires and drawing stock" to revise EN 1715-2:1997. Besides editorial adjustments in the text and update of normative references, the following changes have been made: Clause 3: amended; Table 1 inclusion of alloys EN AW-1110, EN AW-5005, EN AW-8030 and EN AW-8176; Clause 4: amended. EN 1715 comprises the following parts under the general title: "Aluminium and aluminium alloys – Drawing stock": Part 1: General requirements and technical conditions for inspection and delivery Part 2: Specific requirements for electrical applications Part 3: Specific requirements for mechanical uses (excluding welding) Part 4: Specific requirements for welding applications Part 5: Specific requirements for aluminium food packaging1) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard.
1) Under preparation.
prEN 1715-2:2007 (E) 4 1 Scope This European Standard specifies requirements for drawing stock of aluminium and aluminium alloys for electrical applications. The general requirements and technical conditions for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.