Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

This European Standard applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2. This European Standard deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.This European Standard is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its function and can be operated adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.This part 1 describes and defines the safety requirements of rear loaded RCV excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) as illustrated in Figure A.1.Safety requirements for the lifting device(s) and the interface with the tailgate/discharge door are defined in prEN 1501-5.This European Standard is not applicable to:- operation in severe conditions e.g. extreme environmental conditions such as:- below - 25 °C and above + 40 °C temperatures;- tropical environment;- wind velocity in excess of 75 km/h;- contaminating environment;- corrosive environment;- operation in potentially explosive atmospheres;- handling of loads the nature of which could lead to dangerous situations (e.g. hot wastes, acids and bases, radioactive materials, contaminated waste, especially fragile loads, explosives);- operation on ships.This European Standard is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

Abfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine Anforderungen und Sicherheitsanforderungen - Teil 1: Hecklader

Bennes de collecte des déchets - Exigences générales et exigences de sécurité - Partie 1 : Bennes à chargement arrière

Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za zbiranje odpadkov z nakladanjem zadaj

General Information

Status
Not Published
Public Enquiry End Date
14-Oct-2014
Technical Committee
Current Stage
98 - Abandoned project (Adopted Project)
Start Date
08-Oct-2019
Due Date
13-Oct-2019
Completion Date
08-Oct-2019

Relations

Buy Standard

Draft
EN 1501-1:2011/kFprA1:2014
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1501-1:2011/kFprA1:2014
01-september-2014
Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za
zbiranje odpadkov z nakladanjem zadaj
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear
loaded refuse collection vehicles
Abfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine
Anforderungen und Sicherheitsanforderungen - Teil 1: Hecklader
Bennes de collecte des déchets - Exigences générales et exigences de sécurité - Partie
1 : Bennes à chargement arrière
Ta slovenski standard je istoveten z: EN 1501-1:2011/FprA1
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
43.160 Vozila za posebne namene Special purpose vehicles
SIST EN 1501-1:2011/kFprA1:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1501-1:2011/kFprA1:2014

---------------------- Page: 2 ----------------------

SIST EN 1501-1:2011/kFprA1:2014

EUROPEAN STANDARD
FINAL DRAFT
EN 1501-1:2011
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
July 2014
ICS 43.160
English Version
Refuse collection vehicles - General requirements and safety
requirements - Part 1: Rear loaded refuse collection vehicles
Bennes de collecte des déchets - Exigences générales et Abfallsammelfahrzeuge und die dazugehörigen
exigences de sécurité - Partie 1 : Bennes à chargement Schüttungen - Allgemeine Anforderungen und
arrière Sicherheitsanforderungen - Teil 1: Hecklader
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 183.

This draft amendment A1, if approved, will modify the European Standard EN 1501-1:2011. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1501-1:2011/FprA1:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1501-1:2011/kFprA1:2014
EN 1501-1:2011/FprA1:2014 (E)
Contents Page
Foreword .3
1 Modification to Clause 2, Normative references .4
2 Modification to 5.2.3.3, Guide flap.4
3 Modifications to 5.2.3.6, Protective devices .4
4 Modifications to 5.10.3.1, Footboards .4
5 Modifications to 5.10.3.3, Provisions for footboard(s).5
6 Modification to 5.15.1, General .5
7 Modification to 7.1.1.2, Visual .5
8 Modifications to Annex B (normative), Open and closed systems – Footboard(s) .5

2

---------------------- Page: 4 ----------------------

SIST EN 1501-1:2011/kFprA1:2014
EN 1501-1:2011/FprA1:2014 (E)
Foreword
This document (EN 1501-1:2011/FprA1:2014) has been prepared by Technical Committee CEN/TC 183
“Waste management”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been pr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.